topminingcontracts
|
|
March 31, 2014, 10:07:01 PM |
|
^in a month or two time is a different story. my point was just that switching today would be a bad decision with regards to profitability. Sometimes, I forgot that I don't have to argue with people who agree with my standpoint. +1. I thought you were crazy enough to underclock your farm today - doing it in a month from now would be much more reasonable (though you might have better luck selling the hardware to buy 28nm gear at that point in time) Well even if may void guarantee.... The guy is a genius. Congrats
|
▄████▄ ▄████████▄ ▄████████████▄ ▄████████████████▄ ████████████████████ ▄█▄ ▄███▄ ▄███▄ ▄████████████████▀ ▄██████████ ▄▄▄▀█████▀▄▄▄▄▀█████▀▄▄▄ ▀██▄ ▄██▀ ▀██▄ ▄██▀ ▀██▄ ▄██▀ ██ ▄█████▄▀▀▀▄██████▄▀▀▀▄█████▄ ▀██▄ ▄██▀ ▀██▄ ▄██▀ ▀██▄ ▄██▀ ▄█▄ ▀██████████████▄ ████████████████████████████ ▀██▄ ▄██▀ ▀██▄ ▄██▀ ▀██▄ ▄██▀ ▀█▀ ██ ▀████████████████████████▀ ▀██▄ ▄██▀ ▀██▄ ▄██▀ ▄█▄ ▀██▄ ▄██▀ ██ ▀████████████████████▀ ▀███▀ ▀███▀ ▀█▀ ▀███▀ ▄███████████████████████████████████▀ ▀████████████████▀ ▀████████████▀ ▀████████▀ ▀████▀
| ║║ ║█ ║█ ║║ | .
| .
║║ ██ ║║
| .
| .
║║ ██ ║║
| .
| ║║ █║ █║ ║║ | |
|
|
|
Threader
|
|
March 31, 2014, 10:29:47 PM |
|
awsome mod.
I applied it and set the clock at 325.
165 Gh pulling 277watts at the wall
normally 190gh pulls 380watts
Good to know. This mod makes the S1s theoretically cheaper per Ghash than the S2 without sacrificing much power consumption.
According to Jim above's volt mod experience S2 are still much better for power consumption for not much more BTC which i foresee batch 3 to be priced around $3000. 1000gh / 165 = 6.061 x 277 wall watts = 1678 watts 6.061 x S1's = 5.41 BTC Now add the cost of all the power supplies needed for 6 x S1's and the S2 batch 3 will clearly be the smarter option by far.
|
|
|
|
klondike_bar
Legendary
Offline
Activity: 2128
Merit: 1005
ASIC Wannabe
|
|
April 01, 2014, 04:52:39 AM |
|
awsome mod.
I applied it and set the clock at 325.
165 Gh pulling 277watts at the wall
normally 190gh pulls 380watts
Good to know. This mod makes the S1s theoretically cheaper per Ghash than the S2 without sacrificing much power consumption.
According to Jim above's volt mod experience S2 are still much better for power consumption for not much more BTC which i foresee batch 3 to be priced around $3000. 1000gh / 165 = 6.061 x 277 wall watts = 1678 watts 6.061 x S1's = 5.41 BTC Now add the cost of all the power supplies needed for 6 x S1's and the S2 batch 3 will clearly be the smarter option by far. only keep in mind that for the next 2-3 month window, having 1.2TH/2.4kW is better than 1TH/1kW.
|
|
|
|
SVK
|
|
April 01, 2014, 08:58:33 AM |
|
Many thanks for a guide. I see that yous are modifying S1 left and right I have one spare blade with half of the chips not working and was wondering if there is any way I can use this half broken board ? It's the board which didn't have controller board attached to it. Is there any way to connect that board to RPi or even to existing and working S1 ? Thank you very much
|
|
|
|
klondike_bar
Legendary
Offline
Activity: 2128
Merit: 1005
ASIC Wannabe
|
|
April 01, 2014, 03:13:37 PM |
|
Many thanks for a guide. I see that yous are modifying S1 left and right I have one spare blade with half of the chips not working and was wondering if there is any way I can use this half broken board ? It's the board which didn't have controller board attached to it. Is there any way to connect that board to RPi or even to existing and working S1 ? Thank you very much there may be a way to connect it to an upcoming S2 unit if they simply modified the voltage/clocks on the current blade design.
|
|
|
|
SVK
|
|
April 01, 2014, 03:51:53 PM |
|
Many thanks for a guide. I see that yous are modifying S1 left and right I have one spare blade with half of the chips not working and was wondering if there is any way I can use this half broken board ? It's the board which didn't have controller board attached to it. Is there any way to connect that board to RPi or even to existing and working S1 ? Thank you very much there may be a way to connect it to an upcoming S2 unit if they simply modified the voltage/clocks on the current blade design. Many thanks for response Klondike I'm incapable to try anything like this on my own so thought it might be useful to ask on here. So many gurus on here Well I will keep board just in case
|
|
|
|
klondike_bar
Legendary
Offline
Activity: 2128
Merit: 1005
ASIC Wannabe
|
|
April 01, 2014, 06:50:22 PM |
|
Many thanks for a guide. I see that yous are modifying S1 left and right I have one spare blade with half of the chips not working and was wondering if there is any way I can use this half broken board ? It's the board which didn't have controller board attached to it. Is there any way to connect that board to RPi or even to existing and working S1 ? Thank you very much there may be a way to connect it to an upcoming S2 unit if they simply modified the voltage/clocks on the current blade design. Many thanks for response Klondike I'm incapable to try anything like this on my own so thought it might be useful to ask on here. So many gurus on here Well I will keep board just in case Yeah, i cant think of anyway that you could connect it to an S1. AFAIK neither: a) cgminer settings are capable of detecting more than 2 boards b) 2 cards cannot share a dataline for double hashrate. you would either see a lot of duplicate throwaways or HW errors. I do not think it is a 'shared comms' type of connection where multiple boards in parallel would be capable of sharing instructions or hashing 'n-times' faster
|
|
|
|
SVK
|
|
April 01, 2014, 07:50:29 PM |
|
Many thanks for a guide. I see that yous are modifying S1 left and right I have one spare blade with half of the chips not working and was wondering if there is any way I can use this half broken board ? It's the board which didn't have controller board attached to it. Is there any way to connect that board to RPi or even to existing and working S1 ? Thank you very much there may be a way to connect it to an upcoming S2 unit if they simply modified the voltage/clocks on the current blade design. Many thanks for response Klondike I'm incapable to try anything like this on my own so thought it might be useful to ask on here. So many gurus on here Well I will keep board just in case Yeah, i cant think of anyway that you could connect it to an S1. AFAIK neither: a) cgminer settings are capable of detecting more than 2 boards b) 2 cards cannot share a dataline for double hashrate. you would either see a lot of duplicate throwaways or HW errors. I do not think it is a 'shared comms' type of connection where multiple boards in parallel would be capable of sharing instructions or hashing 'n-times' faster I was looking at possibility to solder USB on it or something else and then run it through RPi.
|
|
|
|
vodic62
Newbie
Offline
Activity: 11
Merit: 0
|
|
April 05, 2014, 03:43:40 PM Last edit: April 05, 2014, 04:04:35 PM by vodic62 |
|
I have undervolted my Antminer to 1,0V (R3 = 3.9kOhm) and I am really happy with results. Before mod my antminer was consuming 348W on the wall on 180GH/s but now it takes only 260W on 165GH/s. So 8,3% performance decrease means 25.3% power input decrease. Nice I am running about hour now and no HW errors at all. I also tried 180GH/s with lowered voltage, but a lot of HW errors resulted in 170GH/s output performance too. Mod was really easy. 10 minutes of work and everything worked on the first try. Thanks for the guide.
|
|
|
|
klondike_bar
Legendary
Offline
Activity: 2128
Merit: 1005
ASIC Wannabe
|
|
April 05, 2014, 03:57:31 PM |
|
Has nobody overclocked or overvolted an S2 yet?
640 chips (an S1 has 64 chips), 16 chips per TPS53355 regulator (S1 has 8 per) S1 was forcing around 30A through the regulator at stock speeds, and up to 40A with overclocking and some overvolting (based on some of the 210GH+ reports in this thread) S2 is putting about 22-24A on the regulator at stock. Presumably with a bit of voltage modding and overclocking the regulators could handle up to about 1.4TH/2kW
only issues: 1) power. To seriously overclock, adding a 600W+ PSU will be necessary 2) cooling. More fans and/or individual chip heatsinks are necessary to properly exhaust any extra heat since the units read 50C+ temperatures stock 2b) PCI entenders. Looks like the boards are all mounted using PCI (PCIe 16x?) slots. if you used some risers (with a nice pair of 14AWG power cables to protect the risers) you could get the boards up out of the case and arrange them with airflow directly aimed at the heatsinks for better cooling.
I can't wait for my batch 2 unit to arrive - if noone overclocks by then I might have to be the first. (donations will be accepted in case i kill my miner :p)
|
|
|
|
Zetler
Newbie
Offline
Activity: 42
Merit: 0
|
|
April 08, 2014, 07:20:24 AM |
|
What are the risks of undervolting? I don't know the physics of it, so please excuse my ignorance 1. If I undervolt but do not underclock, what will happen? Will HW errors simply increase, or do I risk the antminer getting damaged? 2. If I both undervolt and underclock, but it turns out I undervolted too much, the same logic applies as in #1? 3. I do not have a volt meter (and I dont know how to use one). Can I simply try with a little bit? The risk is applying too much graphite, not too little, right?
|
|
|
|
lowerjerzey
Member
Offline
Activity: 106
Merit: 10
🤖UBEX.COM 🤖
|
|
April 08, 2014, 03:15:57 PM |
|
Thanks for the guide, OP. I plan on sucking every last ounce out of profitability out of my S1s. This will definitely come in handy in a couple months.
Instead of pencil, I plan on a more permanent solution by soldering a 9.1K ohm resistor in parallel. I'm very new to soldering, so I won't dare to try to replace the flat resistor. I plan on just tinning the ends of the 9.1k resistor, hold it to the side of the flat resistor, then hitting the flat resistor with the iron to get it to tack. Then, repeat for the other side. Is this correct? Any suggestions would be appreciated.
Also, is a 9.1K ohm resistor correct?
r2 = (r1 * rtotal)/(r1 - rtotal) r2 = (4.47K * 3K)/(4.47K - 3K) r2 = 9.12K ohms
Thanks
|
|
|
|
Threader
|
|
April 08, 2014, 03:28:47 PM |
|
if you are going to trouble yourself to soldering a solid resistor then it would make more sense to solder A POTentiometer and have the flexibility of adjustable resistor settings.
|
|
|
|
Trends
Member
Offline
Activity: 119
Merit: 10
|
|
April 08, 2014, 04:42:48 PM Last edit: April 09, 2014, 08:26:35 PM by Trends |
|
If you are going to pull off the resistors you had better have one big ass magnifying glass. I've just completed this on one of my S1's to play with (able to put 0.6V to 1.2V to VDD of Bitmains chip now). I took some pictures and I'll try to get them on later today.
|
|
|
|
lowerjerzey
Member
Offline
Activity: 106
Merit: 10
🤖UBEX.COM 🤖
|
|
April 08, 2014, 04:50:12 PM |
|
if you are going to trouble yourself to soldering a solid resistor then it would make more sense to solder A POTentiometer and have the flexibility of adjustable resistor settings.
That would be ideal for fine tuning but for being novice at soldering, wiring in a pot adds more difficulty than I am comfortable with. Tacking on a resistor to the sides of the existing resistor seems a little more doable for my skill level. And it's only $5 vs about $55 for the pots. But, now that I think about it more, pencil would work just fine. I wanted to add the resistor so I wouldn't have to worry about the graphite potentially flaking off. But even if it did, having them hooked to a kill a watt would show a rise in electricity use. Then I would just have to check each voltage to find the culprit and just add more pencil.
|
|
|
|
klondike_bar
Legendary
Offline
Activity: 2128
Merit: 1005
ASIC Wannabe
|
|
April 08, 2014, 08:24:57 PM |
|
if you are going to trouble yourself to soldering a solid resistor then it would make more sense to solder A POTentiometer and have the flexibility of adjustable resistor settings.
That would be ideal for fine tuning but for being novice at soldering, wiring in a pot adds more difficulty than I am comfortable with. Tacking on a resistor to the sides of the existing resistor seems a little more doable for my skill level. And it's only $5 vs about $55 for the pots. But, now that I think about it more, pencil would work just fine. I wanted to add the resistor so I wouldn't have to worry about the graphite potentially flaking off. But even if it did, having them hooked to a kill a watt would show a rise in electricity use. Then I would just have to check each voltage to find the culprit and just add more pencil. go with a pencil mod - i did it for my bitfury cards (exact same regulator with 2 voltage-controlling resisters) and it works great. It isnt worth the effort and risks of desoldering pcb components and swapping in new resistors when a few rubs with a pencil works fine. tips: 1) get an artist pencil such as a 3B instead of a 2. It is a bit softer and leaves a tiny bit more soft graphite for a rub - a little bit easier to tweak the resistance this way 2) start small. Over time, the pencil mod will 'age' and slightly decrease the resistance even frther than when it was first applied, as the graphite is baked by the hot pcb. leave a little bit of headroom when you do a mod, and expect the resulting voltage to drift a little bit over a 4-12 hour period. (drifts up if overvolting and down if undervolting)
|
|
|
|
Trends
Member
Offline
Activity: 119
Merit: 10
|
|
April 09, 2014, 04:46:45 PM |
|
Added link to my pictures of the 10k pot addition to S1's. http://imgur.com/a/8SUO8
|
|
|
|
lowerjerzey
Member
Offline
Activity: 106
Merit: 10
🤖UBEX.COM 🤖
|
|
April 09, 2014, 06:31:23 PM |
|
Nice job! *looks for a pencil*
|
|
|
|
tzortz
|
|
April 09, 2014, 09:10:12 PM |
|
Now looks better.
|
All is Mine!
1H7LUdfx9AFTMSXPsCBror3RDk57zgnc2R
|
|
|
Trends
Member
Offline
Activity: 119
Merit: 10
|
|
April 09, 2014, 11:12:44 PM |
|
Thanks couldn't see how to post the picture directly in the reply.
|
|
|
|
|