shadeslayer
Newbie
Offline
Activity: 10
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 18, 2022, 08:51:55 AM |
|
Does --lock-mclock 8400 work on Linux? Seem like anything below base memory clock works, but anything above still gets stuck at GPU base memory.
Example if I set --locl-mclock to 5000, it works and sets at 5000, but if I set at 8000 it gets stuck at 6500.
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 18, 2022, 02:12:42 PM |
|
Does --lock-mclock 8400 work on Linux? Seem like anything below base memory clock works, but anything above still gets stuck at GPU base memory.
Doesn't work on the highest clocks. If you set the gpu in P0 mode with nvidia-smi it can go abit higher. but not to 8400. Use another program to set the memclock.
|
|
|
|
KillrBee
Jr. Member
Offline
Activity: 139
Merit: 3
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 27, 2022, 11:32:33 PM |
|
We need to shorten the time between when a card 'times out' and when the miner restarts. I've never seen a card recover from a timeout and often times 3-4 will all timeout at the same time which drops my average hashrate significantly, which also affects my poolside share of a given round.
I mean ideally the AMD cards wouldn't just randomly time out, but if they do, I'd rather just have the process restart than wait for the inevitable crash while hashing at a low rate.
|
|
|
|
KillrBee
Jr. Member
Offline
Activity: 139
Merit: 3
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 28, 2022, 02:19:41 PM |
|
After a lot of head-scratching and tuning with many crashes and poor hash rates, I finally have found a combination of clocks and intensity that allows the 3090Ti to perform well. In the following screenshots -- WhiteFang is the 3090Ti and it has been running for about 10 hours now without any crashes. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FhzPGRrml.png&t=665&c=jc6971u4iFXrHw) ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FWgB8kTnl.png&t=665&c=XTzwCUqb5OwdvQ)
|
|
|
|
Dr_Victor
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
April 28, 2022, 07:18:52 PM |
|
In 8-card-rig of GTX 1080Ti the first card drops down hash from 43 to 10 and even 3 Mh periodically.
|
yobit.net is banned from signatures
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 04, 2022, 02:34:14 PM |
|
In the following screenshots -- WhiteFang is the 3090Ti and it has been running for about 10 hours now without any crashes. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FhzPGRrml.png&t=665&c=jc6971u4iFXrHw) ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FWgB8kTnl.png&t=665&c=XTzwCUqb5OwdvQ) Can you try v1.63 please? If you still get problems, try the SSL port. We have rewritten the code here. SSL Should work on all the supported pools.
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 05, 2022, 04:29:32 PM |
|
On other 2 rigs i'm running NVIDIA ( RTX 2000 series and rtx 3000 seris ) with TBM with same settings for ETH + ZIL and they are running stable and well, just got this error in AMD cards i have 6800XT and 6600XT.
Our AMD test rigs is running without any issues on v1.63. Please test the latest version.
|
|
|
|
KillrBee
Jr. Member
Offline
Activity: 139
Merit: 3
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 06, 2022, 05:10:26 PM Last edit: May 06, 2022, 05:25:26 PM by KillrBee |
|
On other 2 rigs i'm running NVIDIA ( RTX 2000 series and rtx 3000 seris ) with TBM with same settings for ETH + ZIL and they are running stable and well, just got this error in AMD cards i have 6800XT and 6600XT.
Our AMD test rigs is running without any issues on v1.63. Please test the latest version. I've been running 1.63 with different cards running different intensities and the rig has been stable, no GPU timeouts. Overall average hashrate on the AMD cards is 62 MH/s, reported average is 65 Mh/s, so in general the reported and actuals are close -- how the peaks and valleys align with the 2miners reporting window has a more significant effect on the hashrate than anything -- I wish they had a more controllable window, but the ETH earned per day is aligning with the values coming out of various hashrate profit calculators based on the miner reported values. I do notice that once in a while, one of the cards will drop its hashrate for a minute from 65-66 MH/s to 40-something and go back to its previous rate a minute later, but that's not really an issue, just some funny behaviour. I'm super impressed with how the 3090Ti is working with the miner software. I am running 9992 intensity with zero stale or invalid hashes -- I set it to autotune and notice that it seems to switch between kernel 2 and kernel 13, any idea why it's only those two kernels that are putting up 100's vs. 99's for the others (aside from kernel 0 which is like 70)? Performance is 136-137 MH/s from the miner and 135-136 at the pool. Temperatures on the 3090Ti are great!! probably the coolest card in all my rigs running no hotter than 52/68 Degrees (Core/Memory) @ 337 watts.
|
|
|
|
KillrBee
Jr. Member
Offline
Activity: 139
Merit: 3
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 08, 2022, 12:19:06 AM |
|
Update: I did get a timeout on the AMD GPU about 5 1/2 hours after a reboot. Cards crashed (still showed as hashing for about 4 minutes, but the calculated Hashrate/W jumped up):
00:05:26 [2022-05-07 17:36:30.130] GPU5 3090 CUDA 2 6800 43/0 95 1500 11275 333 00:05:26 [2022-05-07 17:36:30.130] 919 00:05:26 [2022-05-07 17:36:30.130] 00:05:26 [2022-05-07 17:36:30.130] ID BOARD HASHRATE/W HASHRATE AVERAGE SHARES RATE 00:05:26 [2022-05-07 17:36:30.130] GPU0 gfx1030 1947.58 kH/W 66.22 MH/s 66.14 MH/s 133/0/0 100.00% 00:05:26 [2022-05-07 17:36:30.130] GPU1 gfx1030 2285.92 kH/W 66.29 MH/s 66.29 MH/s 128/0/0 100.00% 00:05:26 [2022-05-07 17:36:30.130] GPU2 gfx1030 2269.47 kH/W 65.81 MH/s 65.82 MH/s 144/0/1 100.00% 00:05:26 [2022-05-07 17:36:30.130] GPU3 gfx1030 1882.83 kH/W 65.90 MH/s 65.90 MH/s 135/0/0 100.00% 00:05:26 [2022-05-07 17:36:30.130] GPU4 gfx1030 2456.14 kH/W 66.32 MH/s 66.28 MH/s 137/0/0 100.00% 00:05:26 [2022-05-07 17:36:30.130] GPU5 3090 399.57 kH/W 133.06 MH/s 133.05 MH/s 296/0/0 100.00% 00:05:26 [2022-05-07 17:36:30.130] 1873.58 kH/W 463.59 MH/s 463.47 MH/s 973/0/1 100.00% 00:05:26 [2022-05-07 17:36:30.130] 00:05:26 [2022-05-07 17:36:30.130] SHARES PER MINUTE: 2.98 POOL HASHRATE: 434.08 MH/s
Then they posted the failure:
00:05:29 [2022-05-07 17:39:30.159] GPU2: has timed out, trying to restart.. 00:05:29 [2022-05-07 17:39:30.159] GPU4: has timed out, trying to restart.. 00:05:29 [2022-05-07 17:39:30.160] 00:05:29 [2022-05-07 17:39:30.160] 00:05:29 [2022-05-07 17:39:30.160] us-eth.2miners.com (ethash) PING: 36ms DIFFICULTY: 2.03 EPOCH: 491 00:05:29 [2022-05-07 17:39:30.160] 00:05:29 [2022-05-07 17:39:30.160] 00:05:29 [2022-05-07 17:39:30.160] ID BOARD TYPE KERN XINT TEMP FAN CORE MEM WATT 00:05:29 [2022-05-07 17:39:30.160] GPU0 gfx1030 OpenCL 0 693 27/0 89 1500 1069 114 00:05:29 [2022-05-07 17:39:30.160] GPU1 gfx1030 OpenCL 0 693 25/0 89 1500 1069 104 00:05:29 [2022-05-07 17:39:30.160] GPU2 gfx1030 OpenCL 0 949 26/0 89 1500 1059 120 00:05:29 [2022-05-07 17:39:30.160] GPU3 gfx1030 OpenCL 0 660 24/0 89 1650 1069 124 00:05:29 [2022-05-07 17:39:30.160] GPU4 gfx1030 OpenCL 0 963 25/0 89 1500 1069 109 00:05:29 [2022-05-07 17:39:30.160] GPU5 3090 CUDA 2 6800 42/0 95 1500 11275 333 00:05:29 [2022-05-07 17:39:30.160] 904 00:05:29 [2022-05-07 17:39:30.160] 00:05:29 [2022-05-07 17:39:30.160] ID BOARD HASHRATE/W HASHRATE AVERAGE SHARES RATE 00:05:29 [2022-05-07 17:39:30.160] GPU0 gfx1030 1947.58 kH/W 66.22 MH/s 66.14 MH/s 133/0/0 100.00% 00:05:29 [2022-05-07 17:39:30.160] GPU1 gfx1030 2367.56 kH/W 66.29 MH/s 66.29 MH/s 128/0/0 100.00% 00:05:29 [2022-05-07 17:39:30.160] GPU2 gfx1030 0.00 H/W 0.00 H/s 0.00 H/s 144/0/1 100.00% 00:05:29 [2022-05-07 17:39:30.160] GPU3 gfx1030 1830.53 kH/W 65.90 MH/s 65.90 MH/s 135/0/0 100.00% 00:05:29 [2022-05-07 17:39:30.160] GPU4 gfx1030 0.00 H/W 0.00 H/s 0.00 H/s 137/0/0 100.00% 00:05:29 [2022-05-07 17:39:30.160] GPU5 3090 399.57 kH/W 133.06 MH/s 133.05 MH/s 297/0/0 100.00% 00:05:29 [2022-05-07 17:39:30.160] 1090.87 kH/W 331.46 MH/s 331.37 MH/s 974/0/1 100.00% 00:05:29 [2022-05-07 17:39:30.160] 00:05:29 [2022-05-07 17:39:30.160] SHARES PER MINUTE: 2.96 POOL HASHRATE: 430.56 MH/s 00:05:29 [2022-05-07 17:39:30.160] 00:05:29 [2022-05-07 17:39:33.624] Job d52cb 00:05:29 [2022-05-07 17:39:40.329] GPU5 Solution found in 0.19s (Submit every 21.29 seconds) 00:05:29 [2022-05-07 17:39:40.329] Job d52cc 00:05:29 [2022-05-07 17:39:40.361] Accepted (975/975/1) Reply: 32ms 00:05:29 [2022-05-07 17:39:47.034] Job d52ce 00:05:29 [2022-05-07 17:39:49.273] Job d52d1 00:05:29 [2022-05-07 17:39:51.508] Job d52d2 00:05:29 [2022-05-07 17:39:58.213] Job d52d4 00:05:29 [2022-05-07 17:40:04.919] Job d52d6 00:05:29 [2022-05-07 17:40:11.624] Job d52d9 00:05:30 [2022-05-07 17:40:13.859] Job d52dc 00:05:30 [2022-05-07 17:40:18.329] GPU5 Solution found in 4.60s (Submit every 21.31 seconds) 00:05:30 [2022-05-07 17:40:18.369] Accepted (976/976/1) Reply: 40ms 00:05:30 [2022-05-07 17:40:20.564] Job d52de 00:05:30 [2022-05-07 17:40:29.504] Job d52df 00:05:30 [2022-05-07 17:40:30.163] GPU0: has timed out, trying to restart.. 00:05:30 [2022-05-07 17:40:30.163] GPU1: has timed out, trying to restart.. 00:05:30 [2022-05-07 17:40:30.163] GPU3: has timed out, trying to restart.. 00:05:30 [2022-05-07 17:40:30.163]
Then eventually the miner just stopped
00:05:32 [2022-05-07 17:42:30.171] us-eth.2miners.com (ethash) PING: 36ms DIFFICULTY: 2.03 EPOCH: 491 00:05:32 [2022-05-07 17:42:30.171] 00:05:32 [2022-05-07 17:42:30.171] 00:05:32 [2022-05-07 17:42:30.171] ID BOARD TYPE KERN XINT TEMP FAN CORE MEM WATT 00:05:32 [2022-05-07 17:42:30.171] GPU0 gfx1030 OpenCL 0 693 26/0 89 1500 1069 111 00:05:32 [2022-05-07 17:42:30.171] GPU1 gfx1030 OpenCL 0 693 26/0 89 1500 1069 102 00:05:32 [2022-05-07 17:42:30.171] GPU2 gfx1030 OpenCL 0 949 26/0 89 1500 1059 117 00:05:32 [2022-05-07 17:42:30.171] GPU3 gfx1030 OpenCL 0 660 24/0 89 1650 1069 121 00:05:32 [2022-05-07 17:42:30.171] GPU4 gfx1030 OpenCL 0 963 25/0 89 1500 1069 106 00:05:32 [2022-05-07 17:42:30.171] GPU5 3090 CUDA 2 6800 43/0 95 1500 11275 333 00:05:32 [2022-05-07 17:42:30.171] 890 00:05:32 [2022-05-07 17:42:30.171] 00:05:32 [2022-05-07 17:42:30.171] ID BOARD HASHRATE/W HASHRATE AVERAGE SHARES RATE 00:05:32 [2022-05-07 17:42:30.171] GPU0 gfx1030 0.00 H/W 0.00 H/s 0.00 H/s 133/0/0 100.00% 00:05:32 [2022-05-07 17:42:30.171] GPU1 gfx1030 0.00 H/W 0.00 H/s 0.00 H/s 128/0/0 100.00% 00:05:32 [2022-05-07 17:42:30.171] GPU2 gfx1030 0.00 H/W 0.00 H/s 0.00 H/s 144/0/1 100.00% 00:05:32 [2022-05-07 17:42:30.171] GPU3 gfx1030 0.00 H/W 0.00 H/s 0.00 H/s 135/0/0 100.00% 00:05:32 [2022-05-07 17:42:30.171] GPU4 gfx1030 0.00 H/W 0.00 H/s 0.00 H/s 137/0/0 100.00% 00:05:32 [2022-05-07 17:42:30.171] GPU5 3090 399.58 kH/W 133.06 MH/s 133.05 MH/s 299/0/0 100.00% 00:05:32 [2022-05-07 17:42:30.171] 66.60 kH/W 133.06 MH/s 133.05 MH/s 976/0/1 100.00% 00:05:32 [2022-05-07 17:42:30.171] 00:05:32 [2022-05-07 17:42:30.171] SHARES PER MINUTE: 2.94 POOL HASHRATE: 427.55 MH/s 00:05:32 [2022-05-07 17:42:30.171] root@red-ether:/var/log/miner/teamblackminer# cat teamblackminer.2.log |grep -i -B 15 -A 250 '1873.58' > ~/StillTimimgOut_163.txt
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 09, 2022, 10:40:34 PM |
|
Update: I did get a timeout on the AMD GPU about 5 1/2 hours after a reboot. Cards crashed (still showed as hashing for about 4 minutes, but the calculated Hashrate/W jumped up):
Try to run all the AMD cards in once instance, and the nvidia cards in one instance of the miner. ------------ TBM 100% LHR unlock is coming soon.. My testcard's core clock is dropping to 900 when I boost the memory clock, and this is hurting the performance. I read that others have the same problem, but perhaps I can tweak the kernel to use lower memory temps. edit: Stable test. Will let it run over night. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.ibb.co%2Fw4M85GL%2FLHR-UNLOCK-MAY10.png&t=665&c=CL5pss2TaLPw3g) Shitty clocks on my 3080ti card because it trottle, but managed to tune it abit better. Kernel 0 with 9991 intensity.
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 10, 2022, 01:37:04 PM |
|
The lhr-unlock is pretty much done on windows. the next test is running with AMD/NVIDIA cards in a mix with high intensities on the ssl Port. Linux tomorrow. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.ibb.co%2FNZMy3wb%2Flhr-unlock-10-may.png&t=665&c=0rJ5cB5Fpkl8Xg)
|
|
|
|
sxemini
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 1558
Merit: 69
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 11, 2022, 09:45:11 AM |
|
Update: I did get a timeout on the AMD GPU about 5 1/2 hours after a reboot. Cards crashed (still showed as hashing for about 4 minutes, but the calculated Hashrate/W jumped up):
Try to run all the AMD cards in once instance, and the nvidia cards in one instance of the miner. ------------ TBM 100% LHR unlock is coming soon.. My testcard's core clock is dropping to 900 when I boost the memory clock, and this is hurting the performance. I read that others have the same problem, but perhaps I can tweak the kernel to use lower memory temps. edit: Stable test. Will let it run over night. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.ibb.co%2Fw4M85GL%2FLHR-UNLOCK-MAY10.png&t=665&c=CL5pss2TaLPw3g) Shitty clocks on my 3080ti card because it trottle, but managed to tune it abit better. Kernel 0 with 9991 intensity. If core drops when you raise the mem clock - you run into the powerlimit - increase it. I have seen similiar things on 1 of my 2060S, all of this cards run at 45mh, on 1 card, if i raise the mem - the coreclocks drops to 750. For me it makes no sense because the card only use around 120w, but the powerlimit in the bios is a little bit lower than all other cards and i can´t increase the pl over 100% it is kept there.
|
|
|
|
KillrBee
Jr. Member
Offline
Activity: 139
Merit: 3
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 11, 2022, 02:07:33 PM |
|
If core drops when you raise the mem clock - you run into the powerlimit - increase it. I have seen similiar things on 1 of my 2060S, all of this cards run at 45mh, on 1 card, if i raise the mem - the coreclocks drops to 750. For me it makes no sense because the card only use around 120w, but the powerlimit in the bios is a little bit lower than all other cards and i can´t increase the pl over 100% it is kept there.
When the core drops to 750 on that one card, if you're using HiveOS or linux, run "nvidia-info" and it will report if the card is being throttled and the reason for it. If the card isn't reporting any throttle but you can't manually push it above 750 MHz then it most likely is a power problem and that particular card is sensing decreased amperage which will cause it to limit without reporting. I've seen 1000 watt PSUs that can only supply 700 watts consistently and will run into issues when loaded beyond that -- it can run 1000 watts transiently to provide power for a rapid spike load, but just not for more than a few seconds.
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 11, 2022, 09:12:59 PM |
|
Our 100% LHR unlock is running at full speed on the latest driver. 511.65 (windows) and works on all memory algos.
So I guess we do it a bit different than the other teams.. Linux version is delayed some more days..
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 13, 2022, 03:05:45 PM Last edit: May 13, 2022, 03:37:47 PM by sp_ |
|
Check out new The Black Pill enlargement tool 100% LHR unlocker for NVIDIA LHR cards. https://bitcointalk.org/index.php?topic=5398536.0Unlock your LHR cards and hash at fullspeed with the Team Black Miner, Phoenixminer, Srbminer, Miniz, ethminer etc..
|
|
|
|
PsKminer
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 118
Merit: 11
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 15, 2022, 01:16:14 AM |
|
Try the pill with your v1.27 and thank me later.
|
|
|
|
wasarianta
Newbie
Offline
Activity: 40
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 15, 2022, 03:07:22 PM |
|
Check out new The Black Pill enlargement tool 100% LHR unlocker for NVIDIA LHR cards. https://bitcointalk.org/index.php?topic=5398536.0Unlock your LHR cards and hash at fullspeed with the Team Black Miner, Phoenixminer, Srbminer, Miniz, ethminer etc.. how to install and run third-party s/w in hiveos ? Is it same like adding custom miner?
|
|
|
|
|
KillrBee
Jr. Member
Offline
Activity: 139
Merit: 3
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 16, 2022, 02:06:00 PM |
|
Getting a runtime error on HiveOS: ./TheBlackPill.x: /lib/x86_64-linux-gnu/libc.so.6: version `GLIBC_2.33' not found (required by ./TheBlackPill.x) ./TheBlackPill.x: /lib/x86_64-linux-gnu/libc.so.6: version `GLIBC_2.34' not found (required by ./TheBlackPill.x) What version of Linux did you compile this on? HiveOS is still using Ubuntu Version 16.04 LTS and I can't seem to upgrade the system to use any GLIBC_ past 2.29. There are probably some third party ppa: repos that would fix it, but I'm not comfortable using unverified external ppa: repos published by some random on the net. Alternatively I could probably compile/build the GLIBC_## packages and go through the process of relinking things, but it might be at the expense of disabling part of the main kernel, since the libc is so tightly integrated with the kernel, any changes can mess a lot of things up -- and besides, as soon as an upgrade comes along that updates the kernel for the HiveOS distro, I'll have to do it all over again. **** gcc-9 and using the ppa: for ubuntu-toolchain-r/r-test is where I can get GLIBC_2.29 functioning, installing gcc-10 -> gcc-11 don't make a difference and my entire package repo is up to date and upgraded.
|
|
|
|
|