Lottery Solo Pool Miner Race on ckpool

[willi9974]

If that is your goal than yes you can do that.
If you find a block, in the share time on our address we are all happy
And if you find a Block on your private address, than gratulation for your hack

Best regards and have fun and now welcome on my ignore list
Willi

[Sledge0001]

PI1 is now down to a single Compac F (1 of the 2 is now showing 0 chips...)
P12 has 1 Compac F and 4 2PAC's (I had mislabeled them as new pacs)

[kkmonte]

Username: kkmonte_5
Device type: S9_custom
Normal speed: 1100 GH/s

i'll have one more, _6 coming at some point in the next week, then once the bitaxe shows up from china, that will be the end and my miners should be stable and just work away!

Thanks, have update the list.
Did you user the s9 as a heater for your home?

Have sean that kind of heater some times, but the power cost in germany is terrable for that, cant do it.

Best regards from the cold germany
Willi

Hi Willi, you can update kkmonte_4, kkmonte_5, and kkmonte_6 to be S9 miners.  They are running one hashboard so output 1.11 th/s.  I did a bunch of power tests, playing with voltage and mhz of the board to determine the most efficient and cheapest miner for solo mining using my old s9's that I had.  The past 4 winters, I used them to help heat my house, I had them set up around my basement (which is insulated and sealed well) and they made the basement 70 deg F in the winter, which then, the heat made its way up into the main floor.  I ended up saving about 400 gallons of heating oil, which is about $1200-$1300 USD in oil, a small savings with using electric for miners but I was earning btc. 

As you said, for this solo pool miner, it's best to use least amount of electricity, and sacrifice some hashrate since our odds are basically the same whether my miner is running at 1100 gh/s or 3300 gh/s, odds are more or less the same.

Thanks, maybe 2024 will be our lucky year!  have you done any block parties lately?

[willi9974]

Thanks, maybe 2024 will be our lucky year!  have you done any block parties lately?

I run the Blockparty runs every one / two weeks. The last was done yesterday and we start organizing the next one this or latest beginning next week.

I can post the link here or have a look at the cksolo pool topic.

UPDATE: here is the next Blockparty number 57 https://bitcointalk.org/index.php?topic=5237323.msg63523593#msg63523593

Best regards,
Willi


################

new Firmware Version

https://github.com/skot/ESP-Miner/releases

v2.0.6 Latest
What's Changed
revert the order of mining.configure and mining.subscribe by @skot in #81
Full Changelog: v2.0.5...v2.0.6

Known Issues
Some pools complain about the ordering of mining.configure and mining.subscribe but should still work. We are still investigating this issue in #80


Quelle: https://github.com/skot/ESP-Miner/releases


Best regards
Willi

[100knot2dae]

Hello Willi, nice idea with the miner race!

I just configured my 4 NewPacs to mine to your willipool address:

Username: 100knot2dae
Device type: 4x NewPac
Normal speed: 352 GH/s

[se7en6301]

Hello everyone!
I want too join too i just point my miner to solo ck pool

username : se7en6301
Miner : r909 gekko
Hash avg : 1.7 t or more


Good luck TO US !

[willi9974]

Hello everyone!
I want too join too i just point my miner to solo ck pool

username : se7en6301
Miner : r909 gekko
Hash avg : 1.7 t or more


Good luck TO US !

Hello Willi, nice idea with the miner race!

I just configured my 4 NewPacs to mine to your willipool address:

Username: 100knot2dae
Device type: 4x NewPac
Normal speed: 352 GH/s

Welcome and cross our fingers for a big big bestshare to crack maybe a block in the future

Amazing how many miner come inter the small idea from me. It makes fun and if you have time, take photo and share it with us how your mining setup looks like. I love that Kinde of pics…

Best regards,
Willi

[kkmonte]

Hey Willi, here are two pics of my setup.  The S9's were old and the previous person who owned them ran them hot and didn't clean them, they were so dirty when i got them, I had to task them all apart, and the control boards won't work with more than 1 hashboard connected so as you see on the left i had to use 3 control boards to control each hashboard.  But having them in one enclosure saves me on the number of fans being run (control board 2 and 3 are set up in immersion mode) and I just let one control board run the fan at 8% speed (that is enough).  I also am using two modular 1000w power supplies that I had, that are completely silent.  Both of these miners don't make hardly any sound, but produce a little bit of heat.  They are only pulling about 680 watts at the wall.


https://i.postimg.cc/FHggZSmS/20240121-153149.jpg

https://i.postimg.cc/nhtGB28Z/20240121-153215.jpg

[willi9974]

There is a new firmware for the small Bitaxe


v2.0.7 Latest
Power management will now use the board version to distinguish capabilities
New Stratum password field
Version rolling now properly configured by stratum server

I have updated the list of miners and added a few pictures I got from one or the other miner here in the topic.

Happy Mining
Willi

[Teraz08]

Good day! I would like to join the pool 

I just setup my device and so don't have 7 days in CKpool yet, but I understand the payout rules. I've pointed my miner at the address as of today!

Username: Teraz08_1
Device type: Bitaxe ULTRA BM1366
Normal speed: 400 GH/s

[willi9974]

Good day! I would like to join the pool 

I just setup my device and so don't have 7 days in CKpool yet, but I understand the payout rules. I've pointed my miner at the address as of today!

Username: Teraz08_1
Device type: Bitaxe ULTRA BM1366
Normal speed: 400 GH/s

Welcome on our small pool.
Cross our fingers to find a block.

With the statistic link you can see your and all the other miner and also have a look to the 7day rule.

https://solorun.lima.zone/ (simple overview)

Best regards,
Willi

[Marslander]

hello, I am new, I have just acquired: mars lander (bitcoin merch) with 3 gekko science key (BM 1397)

I should provide between 925 and 960 GH/s.

I will have a question, as I participate if there is a gain (I would see it on the PI zero Wh which manages the mining software has an oled)

how I would be paid, because the mining address is that of our team (I have a personal BTC address). Thank you for your answers .

[Sledge0001]

hello, I am new, I have just acquired: mars lander (bitcoin merch) with 3 gekko science key (BM 1397)

I should provide between 925 and 960 GH/s.

I will have a question, as I participate if there is a gain (I would see it on the PI zero Wh which manages the mining software has an oled)

how I would be paid, because the mining address is that of our team (I have a personal BTC address). Thank you for your answers .

You will need to mine to the BTC address listed bc1qeuupt2tgerfum8jclt8aklu9cdmzzkwml9lg7c as seen in his example on the first page of this thread:

https://bitcointalk.org/index.php?topic=5478927.0
Example:

User "Willi9974" with 2 miners

configure the first miner with: bc1qeuupt2tgerfum8jclt8aklu9cdmzzkwml9lg7c.willi9974_1
configure the second miner with: bc1qeuupt2tgerfum8jclt8aklu9cdmzzkwml9lg7c.willi9974_2


I can personally attest to Willii9974's honesty and trust.

[Marslander]

thank you for your return, I have correctly put the BTC address provided (I currently provide 941 GH/s) it is necessary to leave a few hours for stability (GH/s)

[willi9974]

thank you for your return, I have correctly put the BTC address provided (I currently provide 941 GH/s) it is necessary to leave a few hours for stability (GH/s)

Welcome Marslander,

i have nothing to add, Sledge0001 has all explained, thanks for that.
But i have one wish, we would collect some pictures of our miner here. if you have time take a picture and link it in a posting, so i can add it on our first page.

Thanks and best regards,
Willi

[Marslander]

I have a picture, but I don't know how to publish it (the picture is on my PC).

[kkmonte]

I whispered to all of my miners today, that I only want them to submit work that results in at least 1T+ best shares, so we'll see if they listen...

[paid2]

I have a picture, but I don't know how to publish it (the picture is on my PC).

You can use this service: https://www.talkimg.com/

You just need to copy/paste the link provided in your reply

[0id1d]

Hi @willi8874, my Compac F has been having some problems so I'm pointing this at the pool for now until I get it running again:

Device: Apollo BTC
Speed: 2 TH/s

Danke!

[willi9974]

Hi @willi8874, my Compac F has been having some problems so I'm pointing this at the pool for now until I get it running again:

Device: Apollo BTC
Speed: 2 TH/s

Danke!

Hi 0id1d

thanks for the information, if it is only for some days, i let the old device in the table. is it for longer or ever, i can edit your device type, no problem.

i have also update the miner list on page one and nice to the the new miner and the new bestshares in the top 10 list...

very nice and a block would be even nicer 

Best regards and a nice weekend, happy mining.
Willi