BitAxe Gamma 601 - 100% Hash Error Starting Firmware v2.14.1 & v2.14.2

[ohio_jaunt]

I have done about everything in the book, and flashed all of these Bitaxes (3x), but they refuse to connect to my Umbrel.local node and show any hashrate whatsoever.  Any ideas?

Originally, I thought it might be my ASUS router, but everything that COULD be a problem has been disabled now, and it was working for years previously.

Any idea why the system would work for years, and now all of the sudden, refuse to hash whatsoever on my solo node?

[ohio_jaunt]

Umbrel.Local seems to be the issue, because the errors return normal when I set my Pool to "public-pool.io"

Has something changed recently that affected the Umbrel node systems on a local configuration?

Does anyone have any insights or idea?  It was working normally for years, so I have no idea what could have changed.

[FP91G]

There's an old rule: if the hardware is working perfectly, there's no need to change the firmware. If you decide to change the firmware, do it on one device for testing. After checking functionality, change the firmware on the remaining devices.

Is it possible to publish the logs?

[ohio_jaunt]

Yea, noted, but I'm not even sure if the firmware update is the precise cause.  It seems to be working fine on Public-Pool.io, but I'd like to use my node if possible...

Nevertheless, how do I attach my log file to this forum?  It doesn't seem to accept standard attached files.  Can I email it?

[FP91G]

Yea, noted, but I'm not even sure if the firmware update is the precise cause.  It seems to be working fine on Public-Pool.io, but I'd like to use my node if possible...

Nevertheless, how do I attach my log file to this forum?  It doesn't seem to accept standard attached files.  Can I email it?

You can use any online service for txt files or publish logs on this forum using the tag

Code:

If the log is too large, it's better to use online services. I'll look at the log and send you a response. Did your custom mining pool work on the old firmware too?

[BitMaxz]

Maybe the Umbrel.Local is refusing to connect to BitAxe.

How do you set up your BitAxe? What URL do you use? Did you just put umbrel.local on the pool URL, or did you put a local IP? Without Stratum protocol?

The logs should give you hints. You can post them here using code tag or follow the FP91G instruction above.

[ohio_jaunt]

I uploaded the logs here:

https://www.dropbox.com/scl/fi/omsudqb8wyo30ls950rc1/bitaxe-logs.txt?rlkey=cbytojrpry62odpd135k0l160&st=6n2vhtru&dl=0

---

But the firmware doesn't have to do with the issue.  I merely have had the issue on 2.14.1/2.  The issue happened suddenly of no correlation to a firmware update.

The umbrel node was hashing for a year with just umbrel.local in the domain, but now it only works if I set it to public pool, even the non-bitaxe products won't connect to the Umbrel node any longer it seems.

[FP91G]

I uploaded the logs here:

https://www.dropbox.com/scl/fi/omsudqb8wyo30ls950rc1/bitaxe-logs.txt?rlkey=cbytojrpry62odpd135k0l160&st=6n2vhtru&dl=0

---

But the firmware doesn't have to do with the issue.  I merely have had the issue on 2.14.1/2.  The issue happened suddenly of no correlation to a firmware update.

The umbrel node was hashing for a year with just umbrel.local in the domain, but now it only works if I set it to public pool, even the non-bitaxe products won't connect to the Umbrel node any longer it seems.

I don't see any errors in these logs, the device is working normally.
The miner connects to stratum+tcp://umbrel.local:2018
error": null

Could you show me the logs where the error occurs?
A few dozen lines would be enough for me, not several thousand.

[philipma1957]

okay I delete the first 90% of the logs.

below is what came after the restart this issue should be here somewhere.

Code:

--- SYSTEM RESTART ---
I (1045) bitaxe: Welcome to the bitaxe - FOSS || GTFO!
I (1051) bitaxe: I2C initialized successfully
I (1056) bitaxe: RST pin initialized to low
I (1160) adc: calibration scheme version is Curve Fitting
I (1160) adc: Calibration Success
I (1190) nvs_config: Used entries: 305
I (1191) nvs_config: Free entries: 451
I (1191) nvs_config: Available entries: 325
I (1193) nvs_config: Total entries: 756
I (1215) device_config: Device Model: Gamma
I (1215) device_config: Board Version: 601
I (1215) device_config: ASIC: 1x BM1370 (128 cores)
I (1219) system: Initial overheat_mode value: 0
I (1227) pp: pp rom version: e7ae62f
I (1229) net80211: net80211 rom version: e7ae62f
I (1235) wifi:wifi driver task: 3fcbe808, prio:23, stack:6656, core=0
I (1250) wifi:wifi firmware version: 4df78f2
I (1250) wifi:wifi certification version: v7.0
I (1250) wifi:config NVS flash: enabled
I (1251) wifi:config nano formatting: disabled
I (1256) wifi:Init data frame dynamic rx buffer num: 32
I (1261) wifi:Init static rx mgmt buffer num: 5
I (1265) wifi:Init management short buffer num: 32
I (1270) wifi:Init static tx buffer num: 16
I (1274) wifi:Init tx cache buffer num: 32
I (1277) wifi:Init static tx FG buffer num: 2
I (1281) wifi:Init static rx buffer size: 1600
I (1285) wifi:Init static rx buffer num: 16
I (1289) wifi:Init dynamic rx buffer num: 32
I (1294) wifi_init: rx ba win: 16
I (1297) wifi_init: accept mbox: 6
I (1301) wifi_init: tcpip mbox: 32
I (1305) wifi_init: udp mbox: 6
I (1309) wifi_init: tcp mbox: 6
I (1313) wifi_init: tcp tx win: 5760
I (1317) wifi_init: tcp rx win: 5760
I (1322) wifi_init: tcp mss: 1440
I (1326) wifi_init: WiFi/LWIP prefer SPIRAM
I (1330) wifi_init: WiFi IRAM OP enabled
I (1335) wifi_init: WiFi RX IRAM OP enabled
I (1345) connect: ESP_WIFI_MODE_STA
I (1346) connect: Wi-Fi Password provided, using WPA2
I (1350) connect: wifi_init_sta finished.
I (1354) wifi:Set ps type: 0, coexist: 0

I (1358) connect: ESP_WIFI setting hostname to: bitaxe_left
I (1365) phy_init: phy_version 711,97bcf0a2,Aug 25 2025,19:04:10
I (1410) wifi:mode : sta (30:ed:a0:17:b6:70) + softAP (30:ed:a0:17:b6:71)
I (1411) wifi:enable tsf
I (1411) wifi:Total power save buffer number: 8
I (1412) wifi:Init max length of beacon: 752/752
I (1417) wifi:Init max length of beacon: 752/752
I (1421) connect: Connecting...
I (1426) connect: wifi_init_sta finished.
I (1427) connect: Configuration Access Point enabled
I (1436) esp_netif_lwip: DHCP server started on interface WIFI_AP_DEF with IP: 192.168.4.1
I (1436) display: SSD1306 (128x32)
I (1448) display: Install panel IO
I (1452) display: Install panel driver
I (1458) display: Initialize LVGL
I (1461) LVGL: Starting LVGL task
I (1482) display: Rotation: 0
I (1583) display: Display init success!
I (1583) input: Install button driver
I (1667) system: Existing overheat_mode value: 0
I (1797) filesystem: Partition size: total: 2884241, used: 756012
I (1798) TPS546: Initializing the core voltage regulator
I (1814) TPS546: Device ID: 54 49 54 6d 24 41
I (1814) TPS546: Power config-OPERATION: 00
I (1815) TPS546: Power config-ON_OFF_CONFIG: 1F
I (1818) TPS546: Reading MFR info
I (1823) TPS546: MFR_ID: 00 00 00
I (1826) TPS546: MFR_MODEL: 00 00 00
I (1831) TPS546: MFR_REVISION: 00 00 00
I (1835) TPS546: Writing new config values
I (1840) TPS546: VOUT_MODE: 97
I (1844) TPS546: ---Writing new config values to TPS546---
I (1850) TPS546: Setting ON_OFF_CONFIG: 1B
I (1855) TPS546: Setting STACK_CONFIG: 0000
I (1860) TPS546: Setting SYNC_CONFIG: 10
I (1864) TPS546: Setting PHASE: 00
I (1868) TPS546: Setting FREQUENCY: 650MHz
I (1873) TPS546: Setting VIN_ON: 4.80V
I (1878) TPS546: Setting VIN_OFF: 4.50V
I (1882) TPS546: Setting VIN_OV_FAULT_LIMIT: 6.50V
I (1888) TPS546: Setting VIN_OV_FAULT_RESPONSE: B7
I (1893) TPS546: Setting VOUT SCALE: 0.25
I (1898) TPS546: Setting VOUT_COMMAND: 1.20V
I (1903) TPS546: Setting VOUT_MAX: 2.00V
I (1908) TPS546: Setting VOUT_MIN: 1.00V
I (1912) TPS546: Setting VOUT_OV_FAULT_LIMIT: 1.25
I (1918) TPS546: Setting VOUT_OV_WARN_LIMIT: 1.16
I (1923) TPS546: Setting VOUT_MARGIN_HIGH: 1.10
I (1928) TPS546: Setting VOUT_MARGIN_LOW: 0.90
I (1933) TPS546: Setting VOUT_UV_WARN_LIMIT: 0.90
I (1939) TPS546: Setting VOUT_UV_FAULT_LIMIT: 0.75
I (1944) TPS546: ----- IOUT
I (1947) TPS546: Setting IOUT_OC_WARN_LIMIT: 25.00A
I (1953) TPS546: Setting IOUT_OC_FAULT_LIMIT: 30.00A
I (1959) TPS546: Setting IOUT_OC_FAULT_RESPONSE: c0
I (1964) TPS546: ----- TEMPERATURE
I (1968) TPS546: Setting OT_WARN_LIMIT: 105C
I (1973) TPS546: Setting OT_FAULT_LIMIT: 145C
I (1978) TPS546: Setting OT_FAULT_RESPONSE: ff
I (1983) TPS546: ----- TIMING
I (1987) TPS546: Setting TON_DELAY: 0ms
I (1991) TPS546: Setting TON_RISE: 3ms
I (1996) TPS546: Setting TON_MAX_FAULT_LIMIT: 0ms
I (2001) TPS546: Setting TON_MAX_FAULT_RESPONSE: 3b
I (2007) TPS546: Setting TOFF_DELAY: 0ms
I (2011) TPS546: Setting TOFF_FALL: 0ms
I (2016) TPS546: Setting PIN_DETECT_OVERRIDE
I (2021) TPS546: -----------VOLTAGE---------------------
I (2027) TPS546: read VIN_ON: 4.80V
I (2032) TPS546: read VIN_OFF: 4.50V
I (2035) TPS546: read VIN_OV_FAULT_LIMIT: 6.50V
I (2041) TPS546: read VIN_UV_WARN_LIMIT: 2.50V
I (2046) TPS546: read VIN_OV_FAULT_RESPONSE: B7
I (2051) TPS546: read VOUT_MAX: 2.00V
I (2055) TPS546: read VOUT_OV_FAULT_LIMIT: 1.50V
I (2061) TPS546: read VOUT_OV_WARN_LIMIT: 1.39V
I (2066) TPS546: read VOUT_MARGIN_HIGH: 1.32V
I (2071) TPS546: read VOUT_COMMAND: 1.20V
I (2076) TPS546: read VOUT_MARGIN_LOW: 1.08V
I (2081) TPS546: read VOUT_UV_WARN_LIMIT: 1.08V
I (2086) TPS546: read VOUT_UV_FAULT_LIMIT: 0.90V
I (2091) TPS546: read VOUT_MIN: 1.00 V
I (2095) TPS546: read STATUS_WORD: 0842
I (2099) TPS546: -----------VOLTAGE/CURRENT---------------------
I (2106) TPS546: read READ_VIN: 5.62V
I (2111) TPS546: read READ_IOUT: -0.26A
I (2115) TPS546: read READ_VOUT: 0.03V
I (2119) TPS546: -----------TIMING---------------------
I (2126) TPS546: read TON_DELAY: 0ms
I (2130) TPS546: read TON_RISE: 3ms
I (2134) TPS546: read TON_MAX_FAULT_LIMIT: 0ms
I (2139) TPS546: read TON_MAX_FAULT_RESPONSE: 3b
I (2144) TPS546: read TOFF_DELAY: 0ms
I (2149) TPS546: read TOFF_FALL: 0ms
I (2153) TPS546: ---------CONFIG--------------------
I (2159) TPS546: read PHASE: 00
I (2162) TPS546: read STACK_CONFIG: 0000
I (2168) TPS546: read SYNC_CONFIG: 10
I (2183) TPS546: read INTERLEAVE: 0020
I (2184) TPS546: read CAPABILITY: d0
I (2184) TPS546: ---------OPERATION------------------
I (2187) TPS546: read OPERATION: 00
I (2191) TPS546: read ON_OFF_CONFIG: 1b
I (2196) TPS546: read COMPENSATION CONFIG
I (2213) TPS546: 13 11 08 19 04
I (2214) TPS546: Clearing faults
I (2215) TPS546: read STATUS_WORD: 0840
I (2216) EMC2101: Initializing EMC2101 (Temperature offset: 0° C)
I (2230) thermal: EMC2101 configuration: Ideality Factor: 24, Beta Compensation: 00
I (2231) power_management: Starting
I (2235) power_management: ASIC Frequency: 525 MHz, Expected hashrate: 1.07GH/s
I (2243) fan_controller: Starting
I (2245) http_server: Starting HTTP Server
I (2247) fan_controller: Set to Startup mode, fan speed: 70.0%
I (2255) dns_server: Socket created
I (2262) dns_server: Socket bound, port 53
I (2255) websocket_api: websocket_api_task starting
I (2267) dns_server: Waiting for data
I (2254) websocket_log: websocket_log_task starting
I (2256) system: Firmware Version: v2.14.2
I (2287) system: AxeOS Version: v2.14.2
I (2291) BAP: Initializing BAP system
I (2298) BAP: BAP system initialized successfully
I (2748) power_management: setting new vcore voltage to 1150mV
I (2748) vcore: Set ASIC voltage = 1.150V
I (2749) TPS546: Vout changed to 1.15 V
I (4267) wifi:ap channel adjust o:1,1 n:11,2
I (4268) wifi:new:<11,2>, old:<1,1>, ap:<11,2>, sta:<11,2>, prof:1, snd_ch_cfg:0x0
I (4269) wifi:state: init -> auth (0xb0)
I (4801) wifi:state: auth -> assoc (0x0)
I (4833) wifi:state: assoc -> run (0x10)
I (5865) wifi:connected with ASUS - IoT, aid = 12, channel 11, 40D, bssid = 62:7c:61:6e:35:02
I (5866) wifi:security: WPA3-SAE, phy: bgn, rssi: -42
I (5870) wifi:pm start, type: 0

I (5871) wifi:dp: 1, bi: 102400, li: 3, scale listen interval from 307200 us to 307200 us
I (5879) wifi:set rx beacon pti, rx_bcn_pti: 0, bcn_timeout: 25000, mt_pti: 0, mt_time: 10000
E (5887) wifi:sta is connecting, cannot set config
I (5892) wifi:AP's beacon interval = 102400 us, DTIM period = 1
I (5898) connect: Acquiring IP...
I (5922) wifi:<ba-add>idx:0 (ifx:0, 62:7c:61:6e:35:02), tid:1, ssn:1, winSize:64
I (6934) connect: IPv4 Address: 192.168.50.38
I (6934) connect: Connected to SSID: ASUS - IoT
I (6935) wifi:mode : sta (30:ed:a0:17:b6:70)
I (6939) esp_netif_handlers: sta ip: 192.168.50.38, mask: 255.255.255.0, gw: 192.168.50.1
I (6946) connect: Configuration Access Point disabled
I (7019) asic_init: Starting ASIC initialization (cold boot mode)
I (7103) wifi:<ba-add>idx:1 (ifx:0, 62:7c:61:6e:35:02), tid:0, ssn:5, winSize:64
I (7220) asic_init: Performing full UART initialization
I (7220) serial: Initializing serial
I (7221) asic_init: Detecting ASIC chips...
I (7224) asic: Initializing 1x BM1370
I (7237) common: Chip 0 detected: CORE_NUM: 0x00 ADDR: 0x00
I (8226) connect: IPv6 Address: FE80::32ED:A0FF:FE17:B670
I (8238) frequency_transition: Ramping up frequency from 50 MHz to 525 MHz
I (8239) pll: Frequency: 56.25 MHz (fb_divider: 189, refdiv: 2, postdiv1: 7, postdiv2: 6)
I (8244) bm1370: Setting Frequency to 56.25 MHz (56.25)
I (8360) pll: Frequency: 62.5 MHz (fb_divider: 175, refdiv: 2, postdiv1: 7, postdiv2: 5)
I (8362) bm1370: Setting Frequency to 62.5 MHz (62.5)
I (8465) pll: Frequency: 68.75 MHz (fb_divider: 165, refdiv: 2, postdiv1: 6, postdiv2: 5)
I (8467) bm1370: Setting Frequency to 68.75 MHz (68.75)
I (8571) pll: Frequency: 75 MHz (fb_divider: 168, refdiv: 2, postdiv1: 7, postdiv2: 4)
I (8573) bm1370: Setting Frequency to 75 MHz (75)
I (8675) pll: Frequency: 81.25 MHz (fb_divider: 182, refdiv: 2, postdiv1: 7, postdiv2: 4)
I (8677) bm1370: Setting Frequency to 81.25 MHz (81.25)
I (8781) pll: Frequency: 87.5 MHz (fb_divider: 168, refdiv: 2, postdiv1: 6, postdiv2: 4)
I (8783) bm1370: Setting Frequency to 87.5 MHz (87.5)
I (8890) pll: Frequency: 93.75 MHz (fb_divider: 180, refdiv: 2, postdiv1: 6, postdiv2: 4)
I (8892) bm1370: Setting Frequency to 93.75 MHz (93.75)
I (8904) websocket: Added WebSocket log client, fd: 43, slot: 0
I (8996) pll: Frequency: 100 MHz (fb_divider: 160, refdiv: 2, postdiv1: 5, postdiv2: 4)
I (8997) bm1370: Setting Frequency to 100 MHz (100)
I (9100) pll: Frequency: 106.25 MHz (fb_divider: 170, refdiv: 2, postdiv1: 5, postdiv2: 4)
I (9101) bm1370: Setting Frequency to 106.25 MHz (106.25)
I (9205) pll: Frequency: 112.5 MHz (fb_divider: 162, refdiv: 2, postdiv1: 6, postdiv2: 3)
I (9206) bm1370: Setting Frequency to 112.5 MHz (112.5)
I (9309) pll: Frequency: 118.75 MHz (fb_divider: 171, refdiv: 2, postdiv1: 6, postdiv2: 3)
I (9310) bm1370: Setting Frequency to 118.75 MHz (118.75)
I (9414) pll: Frequency: 125 MHz (fb_divider: 180, refdiv: 2, postdiv1: 6, postdiv2: 3)
I (9415) bm1370: Setting Frequency to 125 MHz (125)
I (9518) pll: Frequency: 131.25 MHz (fb_divider: 189, refdiv: 2, postdiv1: 6, postdiv2: 3)
I (9519) bm1370: Setting Frequency to 131.25 MHz (131.25)
I (9623) pll: Frequency: 137.5 MHz (fb_divider: 165, refdiv: 2, postdiv1: 5, postdiv2: 3)
I (9624) bm1370: Setting Frequency to 137.5 MHz (137.5)
I (9725) websocket: Added WebSocket api client, fd: 44, slot: 1
I (9727) pll: Frequency: 143.75 MHz (fb_divider: 161, refdiv: 2, postdiv1: 7, postdiv2: 2)
I (9732) bm1370: Setting Frequency to 143.75 MHz (143.75)
I (9837) pll: Frequency: 150 MHz (fb_divider: 168, refdiv: 2, postdiv1: 7, postdiv2: 2)
I (9838) bm1370: Setting Frequency to 150 MHz (150)
I (9941) pll: Frequency: 156.25 MHz (fb_divider: 175, refdiv: 2, postdiv1: 7, postdiv2: 2)
I (9942) bm1370: Setting Frequency to 156.25 MHz (156.25)
I (10046) pll: Frequency: 162.5 MHz (fb_divider: 182, refdiv: 2, postdiv1: 7, postdiv2: 2)
I (10047) bm1370: Setting Frequency to 162.5 MHz (162.5)
I (10151) pll: Frequency: 168.75 MHz (fb_divider: 162, refdiv: 2, postdiv1: 6, postdiv2: 2)
I (10153) bm1370: Setting Frequency to 168.75 MHz (168.75)
I (10227) connect: IPv6 Address: 2600:4040:7ED3:C400:32ED:A0FF:FE17:B670
I (10256) pll: Frequency: 175 MHz (fb_divider: 168, refdiv: 2, postdiv1: 6, postdiv2: 2)
I (10257) bm1370: Setting Frequency to 175 MHz (175)
I (10363) pll: Frequency: 181.25 MHz (fb_divider: 174, refdiv: 2, postdiv1: 6, postdiv2: 2)
I (10368) bm1370: Setting Frequency to 181.25 MHz (181.25)
I (10469) pll: Frequency: 187.5 MHz (fb_divider: 180, refdiv: 2, postdiv1: 6, postdiv2: 2)
I (10470) bm1370: Setting Frequency to 187.5 MHz (187.5)
I (10574) pll: Frequency: 193.75 MHz (fb_divider: 186, refdiv: 2, postdiv1: 6, postdiv2: 2)
I (10575) bm1370: Setting Frequency to 193.75 MHz (193.75)
I (10679) pll: Frequency: 200 MHz (fb_divider: 160, refdiv: 2, postdiv1: 5, postdiv2: 2)
I (10680) bm1370: Setting Frequency to 200 MHz (200)
I (10783) pll: Frequency: 206.25 MHz (fb_divider: 165, refdiv: 2, postdiv1: 5, postdiv2: 2)
I (10785) bm1370: Setting Frequency to 206.25 MHz (206.25)
I (10888) pll: Frequency: 212.5 MHz (fb_divider: 170, refdiv: 2, postdiv1: 5, postdiv2: 2)
I (10889) bm1370: Setting Frequency to 212.5 MHz (212.5)
I (10993) pll: Frequency: 218.75 MHz (fb_divider: 175, refdiv: 2, postdiv1: 5, postdiv2: 2)
I (10997) bm1370: Setting Frequency to 218.75 MHz (218.75)
I (11100) pll: Frequency: 225 MHz (fb_divider: 180, refdiv: 2, postdiv1: 5, postdiv2: 2)
I (11102) bm1370: Setting Frequency to 225 MHz (225)
I (11205) pll: Frequency: 231.25 MHz (fb_divider: 185, refdiv: 2, postdiv1: 5, postdiv2: 2)
I (11206) bm1370: Setting Frequency to 231.25 MHz (231.25)
I (11310) pll: Frequency: 237.5 MHz (fb_divider: 190, refdiv: 2, postdiv1: 5, postdiv2: 2)
I (11311) bm1370: Setting Frequency to 237.5 MHz (237.5)
I (11415) pll: Frequency: 243.75 MHz (fb_divider: 195, refdiv: 2, postdiv1: 5, postdiv2: 2)
I (11417) bm1370: Setting Frequency to 243.75 MHz (243.75)
I (11520) pll: Frequency: 250 MHz (fb_divider: 160, refdiv: 2, postdiv1: 4, postdiv2: 2)
I (11521) bm1370: Setting Frequency to 250 MHz (250)
I (11624) pll: Frequency: 256.25 MHz (fb_divider: 164, refdiv: 2, postdiv1: 4, postdiv2: 2)
I (11626) bm1370: Setting Frequency to 256.25 MHz (256.25)
I (11729) pll: Frequency: 262.5 MHz (fb_divider: 168, refdiv: 2, postdiv1: 4, postdiv2: 2)
I (11730) bm1370: Setting Frequency to 262.5 MHz (262.5)
I (11834) pll: Frequency: 268.75 MHz (fb_divider: 172, refdiv: 2, postdiv1: 4, postdiv2: 2)
I (11835) bm1370: Setting Frequency to 268.75 MHz (268.75)
I (11939) pll: Frequency: 275 MHz (fb_divider: 176, refdiv: 2, postdiv1: 4, postdiv2: 2)
I (11940) bm1370: Setting Frequency to 275 MHz (275)
I (12043) pll: Frequency: 281.25 MHz (fb_divider: 180, refdiv: 2, postdiv1: 4, postdiv2: 2)
I (12044) bm1370: Setting Frequency to 281.25 MHz (281.25)
I (12148) pll: Frequency: 287.5 MHz (fb_divider: 161, refdiv: 2, postdiv1: 7, postdiv2: 1)
I (12149) bm1370: Setting Frequency to 287.5 MHz (287.5)
I (12253) pll: Frequency: 293.75 MHz (fb_divider: 188, refdiv: 2, postdiv1: 4, postdiv2: 2)
I (12254) bm1370: Setting Frequency to 293.75 MHz (293.75)
I (12358) pll: Frequency: 300 MHz (fb_divider: 168, refdiv: 2, postdiv1: 7, postdiv2: 1)
I (12359) bm1370: Setting Frequency to 300 MHz (300)
I (12468) pll: Frequency: 306.25 MHz (fb_divider: 196, refdiv: 2, postdiv1: 4, postdiv2: 2)
I (12477) bm1370: Setting Frequency to 306.25 MHz (306.25)
I (12581) pll: Frequency: 312.5 MHz (fb_divider: 175, refdiv: 2, postdiv1: 7, postdiv2: 1)
I (12582) bm1370: Setting Frequency to 312.5 MHz (312.5)
I (12686) pll: Frequency: 318.75 MHz (fb_divider: 204, refdiv: 2, postdiv1: 4, postdiv2: 2)
I (12688) bm1370: Setting Frequency to 318.75 MHz (318.75)
I (12792) pll: Frequency: 325 MHz (fb_divider: 182, refdiv: 2, postdiv1: 7, postdiv2: 1)
I (12796) bm1370: Setting Frequency to 325 MHz (325)
I (12897) pll: Frequency: 331.25 MHz (fb_divider: 212, refdiv: 2, postdiv1: 4, postdiv2: 2)
I (12898) bm1370: Setting Frequency to 331.25 MHz (331.25)
I (13002) pll: Frequency: 337.5 MHz (fb_divider: 162, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (13004) bm1370: Setting Frequency to 337.5 MHz (337.5)
I (13107) pll: Frequency: 343.75 MHz (fb_divider: 165, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (13108) bm1370: Setting Frequency to 343.75 MHz (343.75)
I (13212) pll: Frequency: 350 MHz (fb_divider: 168, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (13214) bm1370: Setting Frequency to 350 MHz (350)
I (13316) pll: Frequency: 356.25 MHz (fb_divider: 171, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (13317) bm1370: Setting Frequency to 356.25 MHz (356.25)
I (13421) pll: Frequency: 362.5 MHz (fb_divider: 174, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (13423) bm1370: Setting Frequency to 362.5 MHz (362.5)
I (13526) pll: Frequency: 368.75 MHz (fb_divider: 177, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (13533) bm1370: Setting Frequency to 368.75 MHz (368.75)
I (13634) pll: Frequency: 375 MHz (fb_divider: 180, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (13635) bm1370: Setting Frequency to 375 MHz (375)
I (13738) pll: Frequency: 381.25 MHz (fb_divider: 183, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (13739) bm1370: Setting Frequency to 381.25 MHz (381.25)
I (13843) pll: Frequency: 387.5 MHz (fb_divider: 186, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (13844) bm1370: Setting Frequency to 387.5 MHz (387.5)
I (13948) pll: Frequency: 393.75 MHz (fb_divider: 189, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (13949) bm1370: Setting Frequency to 393.75 MHz (393.75)
I (14053) pll: Frequency: 400 MHz (fb_divider: 160, refdiv: 2, postdiv1: 5, postdiv2: 1)
I (14054) bm1370: Setting Frequency to 400 MHz (400)
I (14157) pll: Frequency: 406.25 MHz (fb_divider: 195, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (14159) bm1370: Setting Frequency to 406.25 MHz (406.25)
I (14262) pll: Frequency: 412.5 MHz (fb_divider: 165, refdiv: 2, postdiv1: 5, postdiv2: 1)
I (14263) bm1370: Setting Frequency to 412.5 MHz (412.5)
I (14367) pll: Frequency: 418.75 MHz (fb_divider: 201, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (14369) bm1370: Setting Frequency to 418.75 MHz (418.75)
I (14472) pll: Frequency: 425 MHz (fb_divider: 170, refdiv: 2, postdiv1: 5, postdiv2: 1)
I (14476) bm1370: Setting Frequency to 425 MHz (425)
I (14578) pll: Frequency: 431.25 MHz (fb_divider: 207, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (14580) bm1370: Setting Frequency to 431.25 MHz (431.25)
I (14683) pll: Frequency: 437.5 MHz (fb_divider: 175, refdiv: 2, postdiv1: 5, postdiv2: 1)
I (14684) bm1370: Setting Frequency to 437.5 MHz (437.5)
I (14788) pll: Frequency: 443.75 MHz (fb_divider: 213, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (14789) bm1370: Setting Frequency to 443.75 MHz (443.75)
I (14893) pll: Frequency: 450 MHz (fb_divider: 180, refdiv: 2, postdiv1: 5, postdiv2: 1)
I (14894) bm1370: Setting Frequency to 450 MHz (450)
I (14997) pll: Frequency: 456.25 MHz (fb_divider: 219, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (14998) bm1370: Setting Frequency to 456.25 MHz (456.25)
I (15102) pll: Frequency: 462.5 MHz (fb_divider: 185, refdiv: 2, postdiv1: 5, postdiv2: 1)
I (15103) bm1370: Setting Frequency to 462.5 MHz (462.5)
I (15207) pll: Frequency: 468.75 MHz (fb_divider: 225, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (15209) bm1370: Setting Frequency to 468.75 MHz (468.75)
I (15312) pll: Frequency: 475 MHz (fb_divider: 190, refdiv: 2, postdiv1: 5, postdiv2: 1)
I (15313) bm1370: Setting Frequency to 475 MHz (475)
I (15416) pll: Frequency: 481.25 MHz (fb_divider: 231, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (15418) bm1370: Setting Frequency to 481.25 MHz (481.25)
I (15521) pll: Frequency: 487.5 MHz (fb_divider: 195, refdiv: 2, postdiv1: 5, postdiv2: 1)
I (15522) bm1370: Setting Frequency to 487.5 MHz (487.5)
I (15626) pll: Frequency: 493.75 MHz (fb_divider: 237, refdiv: 2, postdiv1: 6, postdiv2: 1)
I (15628) bm1370: Setting Frequency to 493.75 MHz (493.75)
I (15731) pll: Frequency: 500 MHz (fb_divider: 160, refdiv: 2, postdiv1: 4, postdiv2: 1)
I (15733) bm1370: Setting Frequency to 500 MHz (500)
I (15835) pll: Frequency: 506.25 MHz (fb_divider: 162, refdiv: 2, postdiv1: 4, postdiv2: 1)
I (15836) bm1370: Setting Frequency to 506.25 MHz (506.25)
I (15940) pll: Frequency: 512.5 MHz (fb_divider: 164, refdiv: 2, postdiv1: 4, postdiv2: 1)
I (15942) bm1370: Setting Frequency to 512.5 MHz (512.5)
I (16045) pll: Frequency: 518.75 MHz (fb_divider: 166, refdiv: 2, postdiv1: 4, postdiv2: 1)
I (16046) bm1370: Setting Frequency to 518.75 MHz (518.75)
I (16150) pll: Frequency: 525 MHz (fb_divider: 168, refdiv: 2, postdiv1: 4, postdiv2: 1)
I (16152) bm1370: Setting Frequency to 525 MHz (525)
I (16254) frequency_transition: Successfully transitioned to 525 MHz
I (16255) asic_init: Setting max baud rate and clearing buffers
I (16257) bm1370: Setting max baud of 1000000 ⁠​‌‌​​​‌​​‌‌​‌​​‌​‌‌‌​‌​​​‌‌​​​​‌​‌‌‌‌​​​​‌‌​​‌​‌⁠
I (16276) serial: Changing UART baud to 1000000
I (16281) asic_init: ASIC initialized successfully with 1 chip(s) (cold boot mode)
I (16289) create_jobs_task: ASIC Job Interval: 500 ms
I (16294) create_jobs_task: ASIC Ready!
I (16296) protocol_coordinator: Protocol coordinator started (primary: SV1, fallback: SV1, state: 1)
I (16296) stratum_v1_task: Opening connection to pool: umbrel.local:2018
I (16295) statistics_task: Starting
I (16296) main_task: Returned from app_main()
I (16347) fan_controller: PID initialized at 59.1°C (P:5.0 I:0.1 D:2.0
I (16350) fan_controller: Set to Auto mode, fan speed: 25.0%
I (18247) fan_controller: Temp: 59.5°C, SetPoint: 60.0°C, Output: 27.4%
I (20247) fan_controller: Temp: 59.8°C, SetPoint: 60.0°C, Output: 29.3%
I (22247) fan_controller: Temp: 60.2°C, SetPoint: 60.0°C, Output: 30.6%
I (23317) stratum_socket: Resolved umbrel.local:2018 → 192.168.50.179
I (23317) stratum_v1_task: Connecting to: stratum+tcp://umbrel.local:2018 (192.168.50.179)
I (23322) stratum_api: TLS disabled, Using TCP transport
I (23328) stratum_v1_task: Transport initialized, connecting to umbrel.local:2018 (192.168.50.179)
I (23820) stratum_v1_task: Resetting stratum uid
I (23820) system: Clean Jobs: clearing queue
I (23820) stratum_api: tx: {"id":1,"method":"mining.configure","params":[["version-rolling"],{"version-rolling.mask":"ffffffff"}]}
I (23833) stratum_api: tx: {"id":2,"method":"mining.subscribe","params":["bitaxe/BM1370/v2.14.2"]}
I (23842) stratum_api: tx: {"id":3,"method":"mining.authorize","params":["bc1q34hptfu50cs4elwh64qa8guxaq6f92csylgtw3.bitaxe_left","x"]}
I (23857) stratum_api: rx: {"id":1,"error":null,"result":{"version-rolling":true,"version-rolling.mask":"1fffe000"}}
I (23866) stratum_v1_task: Set version mask: 1fffe000
I (23898) stratum_api: rx: {"id":2,"error":null,"result":[[["mining.notify","dac7693f"]],"dac7693f",8]}
I (23899) stratum_v1_task: Set extranonce: dac7693f, extranonce_2_len: 8
I (23905) stratum_api: rx: {"id":3,"error":null,"result":true}
I (23911) stratum_v1_task: setup message accepted
I (23917) stratum_api: tx: {"id":4,"method":"mining.suggest_difficulty","params":[1000]}
I (23926) stratum_api: rx: {"id":null,"method":"mining.set_difficulty","params":[100000]}
I (23934) stratum_v1_task: Set pool difficulty: 100000.00
I (23952) stratum_api: rx: {"id":null,"method":"mining.set_difficulty","params":[1000]}
I (23953) stratum_v1_task: Set pool difficulty: 1000.00
I (24247) fan_controller: Temp: 60.5°C, SetPoint: 60.0°C, Output: 31.9%
I (26247) fan_controller: Temp: 60.8°C, SetPoint: 60.0°C, Output: 33.9%
I (28247) fan_controller: Temp: 61.1°C, SetPoint: 60.0°C, Output: 35.3%
I (30247) fan_controller: Temp: 61.4°C, SetPoint: 60.0°C, Output: 37.5%
I (32247) fan_controller: Temp: 61.7°C, SetPoint: 60.0°C, Output: 38.4%
I (34247) fan_controller: Temp: 61.9°C, SetPoint: 60.0°C, Output: 40.0%
I (36247) fan_controller: Temp: 62.2°C, SetPoint: 60.0°C, Output: 42.3%
I (38247) fan_controller: Temp: 62.4°C, SetPoint: 60.0°C, Output: 43.3%
I (40247) fan_controller: Temp: 62.5°C, SetPoint: 60.0°C, Output: 45.7%
I (42247) fan_controller: Temp: 62.7°C, SetPoint: 60.0°C, Output: 45.0%
I (44247) fan_controller: Temp: 62.9°C, SetPoint: 60.0°C, Output: 46.1%
I (46247) fan_controller: Temp: 63.1°C, SetPoint: 60.0°C, Output: 49.2%
I (48247) fan_controller: Temp: 63.2°C, SetPoint: 60.0°C, Output: 50.4%
I (50248) fan_controller: Temp: 63.4°C, SetPoint: 60.0°C, Output: 51.6%

I see zero issues with the possible exception of overheating.  set point of 60c is exceeded to 63.4c

fan speed up from 31 to 51 %

I would try setting fan to 85% manual   and see that temp stays under 60c

also try making frequency lower say 475mhz not 525mhz





lastly repaste heatsink but be careful about it.  do not rush to do this. really go with 85% fan manual setting and see if you stay cool with that setting.

my guess is this is an overheating issue.

[ohio_jaunt]

That is the log where the error occurs, which makes this EVEN MORE CONCERNING.  It literally isn't hashing on Umbrel, but there's no log error?  And the UI says error 100%?  How is that even possible?  Is the network not allowing it to connect or something?

And no, this isn't a heating issue.  As I have said, they all work on any pool other than the Umbrel.local, and there's a Noctua fan on it.  They run at a fine temp.

[philipma1957]

That is the log where the error occurs, which makes this EVEN MORE CONCERNING.  It literally isn't hashing on Umbrel, but there's no log error?  And the UI says error 100%?  How is that even possible?  Is the network not allowing it to connect or something?

And no, this isn't a heating issue.  As I have said, they all work on any pool other than the Umbrel.local, and there's a Noctua fan on it.  They run at a fine temp.

well unfortunately you changed firmware.

So A is this with the new firmware?

B if it is with the new firmware we will never know the older log reads.

[ohio_jaunt]

That is the log where the error occurs, which makes this EVEN MORE CONCERNING.  It literally isn't hashing on Umbrel, but there's no log error?  And the UI says error 100%?  How is that even possible?  Is the network not allowing it to connect or something?

And no, this isn't a heating issue.  As I have said, they all work on any pool other than the Umbrel.local, and there's a Noctua fan on it.  They run at a fine temp.

well unfortunately you changed firmware.

So A is this with the new firmware?

B if it is with the new firmware we will never know the older log reads.

Ok man, I told you like twice, that the firmware has no correlation to the problem I merely gave you what firmware I'm on...

Additionally, you do know... The very log you look at right now, is the error log of the BitAxe not hashing.

Nothing's changed, that system shown in the log literally does not hash whatsoever on umbrel local.  And my point is, it is concerning that you don't see a problem in the log, since it is not working whatsoever, and the firmware has NOT CHANGED.

You don't seem to listen very well...

[FP91G]

That is the log where the error occurs, which makes this EVEN MORE CONCERNING.  It literally isn't hashing on Umbrel, but there's no log error?  And the UI says error 100%?  How is that even possible?  Is the network not allowing it to connect or something?

And no, this isn't a heating issue.  As I have said, they all work on any pool other than the Umbrel.local, and there's a Noctua fan on it.  They run at a fine temp.

well unfortunately you changed firmware.

So A is this with the new firmware?

B if it is with the new firmware we will never know the older log reads.

Ok man, I told you like twice, that the firmware has no correlation to the problem I merely gave you what firmware I'm on...

Additionally, you do know... The very log you look at right now, is the error log of the BitAxe not hashing.

Nothing's changed, that system shown in the log literally does not hash whatsoever on umbrel local.  And my point is, it is concerning that you don't see a problem in the log, since it is not working whatsoever, and the firmware has NOT CHANGED.

You don't seem to listen very well...

Let's slow down a bit.

If the problem isn't with the firmware or the ASIC, since its logs show excellent performance, then I'd assume it's related to the pool settings. Perhaps the device isn't finding valid shares and the pool is showing zero hashrate, or the pool has a high difficulty.

In any case, you need to experiment with the pool settings or run the pool on a remote server for testing.

[ohio_jaunt]

I don't believe it is finding valid shares, and thus showing 0 hash rate/high error.

But why would it have worked for nearly a year straight on the same settings?  I find the abrupt change inexplainable.  These did hash on the local node for nearly 9-11 months straight before.  Suddenly, here we are...

Anything notable change network wise in the last two months?

[BitMaxz]

Have you tried replacing umbrel.local with your unit's IP 192.168.50.179 and put a similar port 2018 and then run and test it again?

I don't see much error from the logs provided, but it looks like it's not the unit issue. I think the issue remains in your umbrel node.
Have you checked if your Umbrel node is still connected to Bitcoin Core and if it's fully synced?

I suggest also check the Umbrel logs look for RPC connection fail or you could also share it with us.