[ANN][MCN] Moneta Verde - CryptoNote coin with difficulty-BR (lnch at 15:00 GMT)

[fibonacho]

Has anyone else got an issue on a win32 box? i have an old one i fired up but it is throwing up "this is not a valid win32 application" error. It is winxp sp3. Is there anything i need to make it work? any  thoughts? thanks

It probably isn't going to work

Ok, thanks

[1714896810]

1714896810

[1714896810]

1714896810

[oldkolobok]

Code:

--node2=127.0.0.1:24081 is IP and MCN's daemon port

why not port 26081

[Amph]

I can't believe that i'm mining the world first fair digital currency! Good work, cryptomidnight!

Yes you are. But as damiano said - it's quite difficult to find a block.

yep

haven't found shit! now

lol

It almost feels as if im not mining.  I hope a pool gets up asap

because the diff is too low and the blocks reward is almost 0, the OP say it all

[vedran82]

Block reward varied from 17.xxx to 19.xxx in the last hour. So no, it's not zero

[bitwho]

how can i solo mine only this coin. no merge?

[BoscoMurray]

Will merge mining spread my hashes across all coins I'm mining?

If so, would I be better solo mining only Moneta Verde if I want all my hashing power pointed at it?

[BoscoMurray]

how can i solo mine only this coin. no merge?

I believe this solo mines it:

monetaverded --start-mining Vdu4S8AFg4pSiAECHvdRniYJd3cMGdaJt4vfMN51rykajA4RxxvQgndc4hYSNf5QzoahpYWUSoXmuLx CJyunSMa113btNC38D --mining-threads 4

[33zer0w0lf]

anyone else here able to compile the source?

[vedran82]

I've run start_mining x (where x is number of threads) from wallet. Works nice, though hashrate is not so great compared to wolf's miner. Then again, it's all about luck... difficulty going uuuup now!

[bitwho]

how can i solo mine only this coin. no merge?

I believe this solo mines it:

monetaverded --start-mining Vdu4S8AFg4pSiAECHvdRniYJd3cMGdaJt4vfMN51rykajA4RxxvQgndc4hYSNf5QzoahpYWUSoXmuLx CJyunSMa113btNC38D --mining-threads 4

can i assign a port to this?

what is the coins port?

[reflector]

anyone else here able to compile the source?

I had errors on ubuntu, but it turned out that the necessary binaries were created and worked.

[shojayxt]

anyone else here able to compile the source?

I compiled on three machines.  Two Ubuntu 12.04 and one 13.10  All had errors and I thought it failed but it did finish and I started mining and have found some blocks.

[hometester]

what is the total coins of MCN?

[BoscoMurray]

how can i solo mine only this coin. no merge?

I believe this solo mines it:

monetaverded --start-mining Vdu4S8AFg4pSiAECHvdRniYJd3cMGdaJt4vfMN51rykajA4RxxvQgndc4hYSNf5QzoahpYWUSoXmuLx CJyunSMa113btNC38D --mining-threads 4

can i assign a port to this?

what is the coins port?

no port required. mines straight to your wallet address

[bitwho]

how can i solo mine only this coin. no merge?

I believe this solo mines it:

monetaverded --start-mining Vdu4S8AFg4pSiAECHvdRniYJd3cMGdaJt4vfMN51rykajA4RxxvQgndc4hYSNf5QzoahpYWUSoXmuLx CJyunSMa113btNC38D --mining-threads 4

can i assign a port to this?

what is the coins port?

no port required. mines straight to your wallet address

yes. but incase i want to use simpleminer or basic knowledge.

if i use localhost:____  <---- how do i find the port for this? is there a way  can assign it as well?

also how do i check balance?

[oldkolobok]

what is the coins port?

see the daemon - port - 26081

[fibonacho]

hmm i just found the claymore miner page, i did not know there was a gpu solution for cn, ill have a go with it later if a pool materialises, has anyone got it working?

it does take 5% though

[MemoryShock]

I don't see a constant update in the Daemon...if I enter the "show_hr" I'll start getting a running list of the hashrate but nothing about blocks.  Is that normal?

[shojayxt]

I don't see a constant update in the Daemon...if I enter the "show_hr" I'll start getting a running list of the hashrate but nothing about blocks.  Is that normal?

Use set_log 1 thru 4 with 4 providing more data.  To stop logging type set_log 0



You can set the level of process detailization* through "set_log <level>" command*, where <level> is between 0 (no details) and 4 (very verbose).

[zdbtc1]

I don't see a constant update in the Daemon...if I enter the "show_hr" I'll start getting a running list of the hashrate but nothing about blocks.  Is that normal?

Here's what you'll see if you find a block with show_hr running and the default log level

Code:

hashrate: 445.3158
2014-Jun-17 13:40:24.697416 [miner 26]Found block for difficulty: 405821
hashrate: 444.5263