[WTS] Custom server PSU breakout boards, 1200w, 1300w, 2000w, 2880w, 4kw

[sorry2xs]

thanks for quick reply, i need watts sooner than January time frame, so i would like to get quote on dps 2000bb with breakout board, 8 pcie cables, 3 hi flow fans, also i would like to know if fans have proper brackets to attach to psu, and a 50 cm to inch conversion, all shipped to Florida 33010 Best Regards. ps do you accept btc.

[J4bberwock]

thanks for quick reply, i need watts sooner than January time frame, so i would like to get quote on dps 2000bb with breakout board, 8 pcie cables, 3 hi flow fans, also i would like to know if fans have proper brackets to attach to psu, and a 50 cm to inch conversion, all shipped to Florida 33010 Best Regards. ps do you accept btc.

Shipping the PSU will probably kill the cost, but I have someone in the US who is stocking boards and cables. And I can arrange something for the PSUs too.

I'll try to gather the price today.
I'm using PCB stands to attach the fans to the PSU, they are working quite well.
I'll check if I still have the pics of this setup.

[L-ZiX]

Please calculate 4 boards for DPS-2000 without PSU and with PCI-E cables. Shipping to Bulgaria.

[gdale]

can you quota me a price for an HP 6 pin PCI-Express 1300 watt Server Power Supply with breakout board and 6 or 12 pci-e connectors.
ty.

[jackbox]

Do you have breakout boards for HP DL580 1300W server supply. I would want to buy one board with 4 cables shipped to Thailand. The lowest cost Air Mail service would be fine. Registered can be added if not too expensive. I hope to hear back from you soon.

[Soab]

Hi J4bberwock,
What is the part number of the connector, I can check with my contacts to see if I can get any. I also would like to buy several of these but really would like them before the end of January.

[bitkilla]

Jabberwock-
I am interested in the boards for the hp1200 DL580 G5 are they instock.
I am trying to figure out cost wise per gh, if I should order the s5 instead
of the c1. I can put two s5's (600 watt each) on one DL580 G5
if I have your board. They need 4 pci-e connectors each so total 8
6 pin pcie connectors off the board. Will that work with normnal or XL?

Do I need an XL I am kind of confused. I pm-ed you also can you please advise?
I would like to order pls contact me.

[J4bberwock]

Jabberwock-
I am interested in the boards for the hp1200 DL580 G5 are they instock.
I am trying to figure out cost wise per gh, if I should order the s5 instead
of the c1. I can put two s5's (600 watt each) on one DL580 G5
if I have your board. They need 4 pci-e connectors each so total 8
6 pin pcie connectors off the board. Will that work with normnal or XL?

Do I need an XL I am kind of confused. I pm-ed you also can you please advise?
I would like to order pls contact me.

Hi, the DPS 1200 FBA and DPS2000BB boards are almost always in stock so no worries for them.
They only exist in XL design for now. A smaller PCI-E design similar to the white one for the HP 1300w is on its way, but probably not released until february.

[aladinsain]

hi could you give me a price for 3 boards for  HP DL580 G3 ML570 G3 power supply 1300 Watts  and 8 pci- 6 pin leads and delivery to uk

[elmatkos]

Hi J4bberwock,

I'm interested in 3x PSU breakout boards for HP 1300w 406421-001 + cables and shipping to Slovakia.

Thnx

[J4bberwock]

Hi, the HP 1300w boards are currently out of stock.
I should get some back in stock next week.

[J4bberwock]

New board made on special request that will be available with a few days delay:
PSU is DPS835-AB, serial numbers 24R2730 - IBM X3650
It delivers 835w even on 110v





Pricing will be as follow:

1-10 boards = 55$
10+ boards = 45$

[elmatkos]

J4bberwock, what are dimensions of that connector for your new board, as I have some Lenovo DPS-800 PSUs and
these are shorter then HP DPS-800 PSUs. I think its like 31 vs 25pins on one side. So maybe this new board for DPS-835
will fit...

[J4bberwock]

J4bberwock, what are dimensions of that connector for your new board, as I have some Lenovo DPS-800 PSUs and
these are shorter then HP DPS-800 PSUs. I think its like 31 vs 25pins on one side. So maybe this new board for DPS-835
will fit...

Hi, sorry, but your lenovo PSU uses a card edge connector like the DPS1200FBA. I'll dig a little on how to start the PSU (unless you already know how) and which connector should be used.
If you have at least 10 PSUs to make, and the connectors is easy to source, it may worth it to make specific boards.
Price should range from 30$ to 45$ depending on the price of the connector and  options needed on the board

[elmatkos]

J4bberwock, what are dimensions of that connector for your new board, as I have some Lenovo DPS-800 PSUs and
these are shorter then HP DPS-800 PSUs. I think its like 31 vs 25pins on one side. So maybe this new board for DPS-835
will fit...

Hi, sorry, but your lenovo PSU uses a card edge connector like the DPS1200FBA. I'll dig a little on how to start the PSU (unless you already know how) and which connector should be used.
If you have at least 10 PSUs to make, and the connectors is easy to source, it may worth it to make specific boards.
Price should range from 30$ to 45$ depending on the price of the connector and  options needed on the board

Hi J4bberwock,

the 12Vsb (stand-by) line will always be live when the system is connected to power. That corresponds to pin B21. To turn on the rest of the PSU, PSON (pin A21) must be shorted to ground (A1-A9, B1-B9). That will turn on the other pins including the +12V rail (A10-A18, B10-B18).

[J4bberwock]

J4bberwock, what are dimensions of that connector for your new board, as I have some Lenovo DPS-800 PSUs and
these are shorter then HP DPS-800 PSUs. I think its like 31 vs 25pins on one side. So maybe this new board for DPS-835
will fit...

Hi, sorry, but your lenovo PSU uses a card edge connector like the DPS1200FBA. I'll dig a little on how to start the PSU (unless you already know how) and which connector should be used.
If you have at least 10 PSUs to make, and the connectors is easy to source, it may worth it to make specific boards.
Price should range from 30$ to 45$ depending on the price of the connector and  options needed on the board

Hi J4bberwock,

the 12Vsb (stand-by) line will always be live when the system is connected to power. That corresponds to pin B21. To turn on the rest of the PSU, PSON (pin A21) must be shorted to ground (A1-A9, B1-B9). That will turn on the other pins including the +12V rail (A10-A18, B10-B18).

Hi, you got a PM, I may have found the mating connector, but I need a few extra infos since I don't have access to this particular PSU.

[klondike_bar]

thought i would throw a post in here - I sell 24" PCIe---PCIe 16awg cables that are ideal for some of the jabberwocky boards. see my signature link for details

(note: the PCIe-PCIe varient costs a little more and that change isnt shown in my threads pricing system YET - its approx $0.10/cable more expensive than the one-ended varient)

[J4bberwock]

thought i would throw a post in here - I sell 24" PCIe---PCIe 16awg cables that are ideal for some of the jabberwocky boards. see my signature link for details

(note: the PCIe-PCIe varient costs a little more and that change isnt shown in my threads pricing system YET - its approx $0.10/cable more expensive than the one-ended varient)

I hope you have some serious stock since I'll have more board soon that will use those cables, and the Bladecenter H board deliveries will start next week.

[klondike_bar]

thought i would throw a post in here - I sell 24" PCIe---PCIe 16awg cables that are ideal for some of the jabberwocky boards. see my signature link for details

(note: the PCIe-PCIe varient costs a little more and that change isnt shown in my threads pricing system YET - its approx $0.10/cable more expensive than the one-ended varient)

I hope you have some serious stock since I'll have more board soon that will use those cables, and the Bladecenter H board deliveries will start next week.

I have about 100 now, and 300 more arriving around the end of the week. For buyers looking at 150+ direct shipping is available and is cheaper/cable but takes an extra week

[MCHouston]

Just wanted to thank J4bberwock for the 2880W boards,  these boards are great.  Very easy to go dense with miners with these boards and their well made not a single issue.  Thanks again.