brooksiedog (OP)
Newbie
Offline
Activity: 8
Merit: 0
|
|
October 01, 2014, 10:23:03 PM |
|
So I got a ASICMiner Tube 800+ GHs from http://www.112bit.com/product/asicminer-tube-800-ghs-sha256-bitcoin-miner-kit/Had to source my own power adapter for the Ethernet Controller .....no bigs but was "fun" Now.....I've accessed it thru Chrome and input all my setting and username etc, BUT it does not start mining, just sitting there at 0.00gh Any ideas? What info should I give you guys to help out ? Ian
|
|
|
|
apollojmr
Sr. Member
Offline
Activity: 311
Merit: 250
The Power Of The Coin Is Awesome!!
|
|
October 03, 2014, 12:12:03 AM |
|
are you in slot 1 of the controller? also when you hit the test button do you see the boards?
|
What you think you become. Bitrated user: apollojmr.
|
|
|
brooksiedog (OP)
Newbie
Offline
Activity: 8
Merit: 0
|
|
October 03, 2014, 01:31:27 AM |
|
yes I see the boards when I press test they all show 0.00 , I only had one connector coming from it to attach the ethernet controller............ the rest were already hooked daisy chained together........
THANKS so much for your ideas, I'll even pay some btc to get this running.
|
|
|
|
brooksiedog (OP)
Newbie
Offline
Activity: 8
Merit: 0
|
|
October 03, 2014, 02:37:45 AM |
|
and yes I'm connected to UART1
|
|
|
|
philipma1957
Legendary
Offline
Activity: 4284
Merit: 8683
'The right to privacy matters'
|
|
October 03, 2014, 10:07:05 AM |
|
copy my mining pool see if you get numbers to show it is mining . you need to have all the dip switches done correctly. a good pool entry and correct ip's. my router is 192.168.0.1 so i can use that for my gateway setting. if you have a router like mine then make sure you can match it up correctly I had 2
|
|
|
|
brooksiedog (OP)
Newbie
Offline
Activity: 8
Merit: 0
|
|
October 03, 2014, 01:48:13 PM |
|
I've input your settings, now it boots up and then after about 20secs both it and my 1000watt power supply turn off................... not blaming the settings just reporting......... its on its own circuit so i know its not a power source issue, *bangs head on desk
|
|
|
|
Trends
Member
Offline
Activity: 119
Merit: 10
|
|
October 03, 2014, 11:30:53 PM |
|
Pull the comm cable from the last daisy chained board and try again. If it holds I'd suggest your PS is not suitable to carry the load of 4 boards.
|
|
|
|
philipma1957
Legendary
Offline
Activity: 4284
Merit: 8683
'The right to privacy matters'
|
|
October 05, 2014, 03:07:54 PM |
|
Pull the comm cable from the last daisy chained board and try again. If it holds I'd suggest your PS is not suitable to carry the load of 4 boards.
what is the op's psu? change the setting for freq from 290 to 250 if it runs and stays running it means your psu can not handle the power load. freq 250 will use less power then freq 290 250 is underclocked 270 is stock 290 is overclock this may be an underpowered psu. I think you may get it running at 250 freq.
|
|
|
|
|
daddyfatsax
|
|
October 08, 2014, 03:05:27 PM |
|
Does ghash allow the password to be d=1024? I always set the difficulty on the worker page. Everything else on the page looks like my tube, so it may be a PSU issue.
|
|
|
|
brooksiedog (OP)
Newbie
Offline
Activity: 8
Merit: 0
|
|
October 09, 2014, 01:52:24 AM |
|
I copied these settings from another user who posted, my settings don't mine either, even tho they work on other miners......
|
|
|
|
brooksiedog (OP)
Newbie
Offline
Activity: 8
Merit: 0
|
|
November 26, 2014, 01:47:21 AM |
|
It was a PSU ISSUE, It took me this long to convince wifey to buy a Zalman 1250PSU and its chugging away with the settings given to me by philip !!!!!!
Now I've tried my settings from slushies pool and nadda........even tho I use them on other miners,,,,,,,,,
Who can reccd a good pool with easy setup
|
|
|
|
talbengal
Newbie
Offline
Activity: 30
Merit: 0
|
|
March 21, 2015, 08:47:51 AM |
|
I had ASICMiner Tube 800+ GHs for the last 3 month, now the controller's rebooting every 2Min. the controller's is working OK when not connecting to the miner, but the moment I connecting it to the miner its start rebooting every 2 Min. Any idea? Please HELP!
|
|
|
|
baykan
|
|
March 28, 2015, 08:00:13 PM |
|
It may be a software issue. I had problems with the controller as well. But not 2 minutes, mining was stopping at random times... The last chance I tried was to use a proxy from Slush's pool. I downloaded the proxy to a pc which is running 7/24 and pointed the erupter to use proxy's IP After that everthing worked fine... You may have a power adapter problem which should be 12V 1Amp. Check it out. That's all I know.
|
|
|
|
baykan
|
|
March 28, 2015, 08:05:37 PM |
|
I may also buy it from you, I can use it with my erupter. You can send me a pm.
you can also try to replace the block erupter with a new one.
|
|
|
|
|