this is just running cgminer with no chip freq or options. undervolted 2.55 @ the resistor. gave it a little bit but i dont wanna run it too long, all i have are little heat sinks on each chip.
|
|
|
Got my 4 s1 blades in last night and a few usb to uart converters. Undervolted to .8 @ 2.6-2.7. With cgminer run it was getting 45-60 ghs, it worked without any options set, also just the basic freq setting worked. Turned it all off and now it won't set freq, still have .8 volts.... so i tried another board without undervolting real quick to see what the issue was and it started to hash. So maybe I have a dead board now? I have a few more boards on the way as well.
I'd check the poolside hashrate, because 60 GH undervolted is way over what I'm getting. I assume you are using the old U2 cgminer build from bitmain? I'm believe I'm using the cgminer build from the u1, I'm at work atm but ill check when I get home. It wasn't 60+, it was more like 57-60. Pool side it was at 15 Gh and climbing until I tinkered and restarted it. I havent been able to get the board to hash after that. I'll undervolt another board later tonight and give it a go and snap some pics. Ok, that makes sense, you should be able to get 15-16 "real" GH/s when undervolted. I was unable to go over 27 GH/s pool side with non modded board. Isn't the u1 rated for 1.6-1.8 on ~.8v. So at 32 chips we should be able to get 50-57 GH per 1 board or close to it. 15 GH sounds like 8 or so chips are working. 32 chips at 15 GH would mean were only getting .5 GH per chip which is a 3rd of a u1 at close the same voltage. Do some of the other pins need to be connected/shorted/grounded together to chain all the chips? If my board sits plugged in not hashing they all get warm at some point.
|
|
|
Got my 4 s1 blades in last night and a few usb to uart converters. Undervolted to .8 @ 2.6-2.7. With cgminer run it was getting 45-60 ghs, it worked without any options set, also just the basic freq setting worked. Turned it all off and now it won't set freq, still have .8 volts.... so i tried another board without undervolting real quick to see what the issue was and it started to hash. So maybe I have a dead board now? I have a few more boards on the way as well.
I'd check the poolside hashrate, because 60 GH undervolted is way over what I'm getting. I assume you are using the old U2 cgminer build from bitmain? I'm believe I'm using the cgminer build from the u1, I'm at work atm but ill check when I get home. It wasn't 60+, it was more like 57-60. Pool side it was at 15 Gh and climbing until I tinkered and restarted it. I havent been able to get the board to hash after that. I'll undervolt another board later tonight and give it a go and snap some pics.
|
|
|
Got my 4 s1 blades in last night and a few usb to uart converters. Undervolted to .8 @ 2.6-2.7. With cgminer run it was getting 45-60 ghs, it worked without any options set, also just the basic freq setting worked. Turned it all off and now it won't set freq, still have .8 volts.... so i tried another board without undervolting real quick to see what the issue was and it started to hash. So maybe I have a dead board now? I have a few more boards on the way as well.
|
|
|
done deal, money sent. thank you.
|
|
|
ok, I'll do it if your interested. whats your paypal?
|
|
|
what would that be in USD? I'm interested, check my trust and LMK.
|
|
|
Deal is done. Thanks, done with out escrow no sweat. .45 BTC for $180 via paypal.
|
|
|
i have a verified paypal, have done paypal transactions here and will use escrow. Check my trust and Lmk.
|
|
|
I'll watch it and maybe bid.
|
|
|
I have purchased a zeusminer thunder x6 18-20 mhash off ebay and I have worked in it for 8 hours last night to get it to hash. First on pc then laptop and lastly r pi. Tried different drivers, cg/bf miner and configs. I would just start cg miner and the psu would turn off. I took it apart and replace the fans while I was in there checking the cables as per some threads. Everything was connected right. Tried just one set of blades and it worked at about 10 mhash and switches were at (all 4 off)/(only 4 on). I tried the same setup (switches) on the other 2 set of blades and it mine at about 10 mhash. Tried setting switches for all 4 and it crashed. I tried 2 psus both 80+, 1000 watt rosewill bronze and 750 watt seasonic gold. At the moment I'm running 3 blades at about 15 mhash pulling 380 watts at the wall. I believe the switches are set to (all 4 off)/(only 4 on)/(only 3 on). I'm at work atm but I'd love to have something to try for when I get home. I do believe I tried (all 4 off)/(only 4 on)/(only 3 on)/(3 and 4 on) also (all 4 off)/(only 4 on)/(3 and 4 on)/(only 3 on). I did set chip counts to 64, 96 and 128 respectivly. Clock was tried 220, 230, 240. Thanks in advance.
If interested I can send you $20 via paypal for the person who gets it fully hashing.
|
|
|
Gridseed blade can be had for ~$100 usd shipped on ebay. Your looking at about 5-7 mhs
|
|
|
I dont have high trust but its good, I have been looking for some bitcoin on here. I have earned trust by sticking my neck out there and have had people send me half payments before i ship as well. Either you send first or we use escrow and I will paypal you $125
|
|
|
sent you a pm and you never got back to me
|
|
|
u should post miner details, pictures, where r u shipping from, not a shitty ebay link ...
I'm sure that's his listing on ebay as per the OP. Ashburn, Virginia, United States is where he is located as per the ebay listing. I agree he could of used real pics, but its on ebay with 100% feedback and ebay money guarantee. He simply posted a link to his ebay listing so if anyone was interested from here that we would know about it.
|
|
|
I am done playing games.... I have done various deals here which included me getting half btc up front/ship/then the other half of payment, shipping first, me sending payment first (btc, pp and me shipping) in a hardware swap. check my trust info. this person accepts pp and never gets back to me this person accepts pp and skrill..... told me skrill only later so i made an account, did a skype screen share and said he didn't like my card was a visa for what ever reason thank god i didnt put the money in there first otherwise I'd have useless money sitting in there right now. I have a good standing on here, my ebay (the-fence-man-1960) is 100% positive, paypal is verified and connected to that ebay..... please someone for the love of god let me buy some btc with out jumping through a flaming hoop while using crutches on a pogo stick while catching a football and tell me its not good enough. I don't have time for bs and games, this is what i can offer if you dont like it dont bother. i have put myself out there to gain a trust status and its like it still don't matter at all. which I can understand to a certain extent.......but damn all i want is a little more btc to buy some alts and im paying for it plain and simple. i get what i want,you get what you ask for and we move on happily. well other than me completing another transaction with you from time to time (im not rich ) Edit: I am fine with you sending btc to a trusted escrow. I have used Tomatocage multiple times upon others.
|
|
|
|