no Grim, that bios is from November 3rd
and honestly, i cant see any difference at OC for now.
|
|
|
thanks for the tip about updating bios on Gigabyte Micron boards.. i had old bios and i couldnt make more that 270 sols with this miner.
I´ve just updated. Lets see if theres any change...
Me too, I updated bios, two weeks ago on gigabytes, and till now no crashes, it improved stability a lot. Can you link the GIGABYTE bios fix for micron VRAM, because I only know of ASUS MSI EVGA Zotac Palit Gainward bios updates for micron vram. http://www.gigabyte.com/products/product-page.aspx?pid=5916&dl=#bios
|
|
|
thanks for the tip about updating bios on Gigabyte Micron boards.. i had old bios and i couldnt make more that 270 sols with this miner.
I´ve just updated. Lets see if theres any change...
|
|
|
i only came to say hello to NotLambChomps or whatever his nick is now. where are the rockets and trains gifs??!!! c´mon!!
|
|
|
Now it is official:
Poloniex is dropping XCN. On January 4th 2017, the following markets will be delisted: MMNXT, BITCNY, NBT, DIEM, LTBC, RDD, XST, XCN, XDN, SYNC, CGA, GEO, BLOCK, 1CR Posted by MobyDick at 2016-12-19 04:33:10
I think it's a mistake, they assured me they weren't going to delist it, as it's doing good volume. nice 50% drop after the announce
|
|
|
270 sols with Gigabyte 1070 G1
|
|
|
Gigabyte GTX 1070 Gaming G1: TDP 55%, no OC, Drivers 376.19, = 300 sol/s
|
|
|
i cant pass 300 sols either..
Gigabyte g1 1070 (6 pin, does it matter??), win 7 64, 4 gb... latest drivers.
|
|
|
I have 2 gigabyte 1070 gaming g1. But the 2nd one's speed jumps so hard. How can i fix it? how do you get 270 sols on a Gigabyte 1070 G1 Gaming??? i cant pass 245.. even with oc what are your drivers/settings??
|
|
|
currently 140 sol on any pool is far worse than 220 sol with nicehash, locked on their pool
Let's not make things up out of thin air. This based on actual payouts rates side by side for proper comparison: Could you share site url with such charts. Thanks. +1 whats the url for those charts?
|
|
|
P0 -> P2 -> P3
So you need at least P2... P3 is slower
ok, then how do i change to P0? nvidia-smi says it cant change state( --gom=0 command)
|
|
|
It seems gpu is in P2 state, but overclocking goes to P3... how can i set the card to P3 ??
|
|
|
no changes for me... 185 sol/s for a Gigabyte G1 1070, same speed as last version
|
|
|
i see speeds above 200sols for a single 1070 rig. Even 2x card rigs have such speeds..
I´m only getting 680 at most with a 4x rig. (Gigab G1)
Win7, 372.54 driver. (-502, +0 , 80% seem to get the better results)
I´m upgrading driver to latest to test. Currently using 1.0.2b miner, what am i missing???
I updated drivers to latest and configured nvidia inspector to +150/+200/70%... same speed (under 700sols) Could it be that my 1070s have Micron memory??
|
|
|
i see speeds above 200sols for a single 1070 rig. Even 2x card rigs have such speeds..
I´m only getting 680 at most with a 4x rig. (Gigab G1)
Win7, 372.54 driver. (-502, +0 , 80% seem to get the better results)
I´m upgrading driver to latest to test. Currently using 1.0.2b miner, what am i missing???
|
|
|
Do you realize that we are all rising the hashrate, rising the diff, and then earning the same as before??
actually nvidia are earning less because it is not on par with amd dont remind me so, Amph.. please
|
|
|
Do you realize that we are all rising the hashrate, rising the diff, and then earning the same as before??
|
|
|
i just burned a small psu in a rig with 8.0 which was fine with 7.0 (i knew it was at the brink of its capabilities). No regrets.. it was an old one.
but beware: Definatly usage power increase in this version.
|
|
|
Claymore, any plans on Nvidia side?
|
|
|
i was afraid to ask, but i cant reach those OC either.. 1070 Gigabyte G1 (micron) best results when mem is -502 meanwhile my old heaters (7950) with ghetto coolers are doing 200 sol/s i bow to that cards the only reason keeping the 1070s is that i´m too lazy to sell them
|
|
|
|