Show Posts
|
Pages: [1]
|
So ive moved the miner away from the tv and the s-video if fine but I still have the same problem with the audio? Actually im not sure why I even come on this forum because I never get any help
|
|
|
Its a ATI HD 4870 and I still have the same problems even after reinstalling everything.
I think the only thing I can try is to move the mining farm further away from it as its currently under the cabinet the tv stands on
|
|
|
Ok, it looks as though the wavy lines on the s-video match the movement of the stratum proxy lines moving up the screen even when i minimize it, im guessing its a graphics card issue and will try to reinstall
|
|
|
This is really weird I have 3 asic blades running now for a few months via stratum proxy with no problems then a few days ago I noticed the audio on my pc starting to stutter and has gotten worse. I reloaded all the drivers and even the codecs to no avail and then tonight my s-video picture started to get all wavy. I shut down the proxy and the blades and the audio and the s-video are fine??? ![Huh](https://bitcointalk.org/Smileys/default/huh.gif) If I start the proxy its fine but when I power up the miners the problem returns? Any ideas?
|
|
|
I am planning on having 4 Asic blades running at roughly 400w and want to get a new PSU as the one I bought recently (a very cheap one) does not seem to be able to run more than 2?? ![Huh](https://bitcointalk.org/Smileys/default/huh.gif) Any suggestions welcome (shipped to uk) cheers
|
|
|
Well I have just tried one of the blades connected directly to the computers PSU and it runs fine so I can only assume the cheap PSU I was using is somehow not giving out enough power. Its rated at 500 and with the three blades consuming 100 it should have been plenty. Maybe when I added the 3rd it blew something in the PSU because that one had a dodgy fuse that kept blowing (see pic) I think I might return that one as it is far from 'perfect working order' As for the PSU Im guessing there is nothing I can do for it if its not putting out enough juice now - anything to be done or should I just buy a good one (this was a very cheap make)? ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fi642.photobucket.com%2Falbums%2Fuu142%2Fkingkurtz%2F2014-01-14122638_zps6ad7dbfb.jpg&t=663&c=Zsr6-vzFmzjO2g) cheers
|
|
|
No, I dont get it, it worked fine before I added the other two and now im back to the original one with the EXACT same settings and still all jobs=FALSE in proxy I have reset the blade a couple of times and set it up again in the config and no change Need some help ![Huh](https://bitcointalk.org/Smileys/default/huh.gif)
|
|
|
Hi all
I was originally running a single REV 2.01 HK green board ASIC miner fine using the Stratum proxy via Slushes pool (ip 192.168.1.201) Then I recently purchased two REV 2.01 HK on the blue board with the fuse and added them (setting 192.168.1.202 for the second and 192.168.1.203 for the third as ips) When I added the fist all was fine and I was getting double the hash rate but when I added the 3rd the proxy stopped accepting any new jobs and now all I am getting is the same clean_jobs=False over and over.
I removed the 2 blue boards and went back to the original green and still the same problem?
I am really stuck as to what the problem is, I can ping the miner fine and see it over the network, maybe I have messed up the pool somehow?
Any help would be greatly appreciated
Cheers Kurtis
|
|
|
Are you talking about temp measured on the board (under the heatsink) or directly on the BE1 chips themselves?
My board temp stays around 32°C right now in a vertical setup, but it used to go up to the 40s °C during summer. Sometimes I would get x'es instead of O's in the Chip: status line, but tuning voltage (V1 blades here) and a fan cleared the problem.
Yes the temp on the board, cheers
|
|
|
I wouldn't worry a bit unless it was over 70C. My CPU's can run up to 90C.
Yeah, I have seen other sites saying the same thing, thanks
|
|
|
Any1? ![Huh](https://bitcointalk.org/Smileys/default/huh.gif)
|
|
|
Hi guys, I have been looking for info on an ideal temp for my asic miner Blade, I have searched these forums but cannot find any discussions on temperatures?
Whats hot and what not?
I have a couple of fans on the heat sink and it runs at about 40-45c at its hottest point, is this ok?
Cheers
Kurtis
|
|
|
Hi guys, I have been looking for info on an ideal temp for my asic miner Blade, I have searched these forums but cannot find any discussions on temperatures?
Whats hot and what not?
I have a couple of fans on the heat sink and it runs at about 40-45c at its hottest point, is this ok?
Cheers
Kurtis
|
|
|
I figured it out myself... ![Tongue](https://bitcointalk.org/Smileys/default/tongue.gif)
|
|
|
I really wanted to sort this myself but seems like I am going round in circles now
I just bought a BLADE VERSION AM BE REV 2.01 HK and have wired it up and its running fine with some fans and nice and cool
I have configured it using the dogie guide and am running the stratum proxy but its still not showing up in the device list in GUIminer?? - im guessing it should?
Its showing as connected via my hub and I can ping it ok
By config is :
IP : 192.168.1.201 Mask : 255.255.255.0 Gateway : 192.168.1.1 WEB Port : 8000 Primary DNS : 194.168.4.100 Secondary DNS : 194.168.8.100 Ports : 8332,8332 Server addresses : 192.168.1.2,192.168.1.2 (my computers ip) user:pass : user.pasword,user.pasword
All these settings are from ipconfig /all so are correct
Am I missing something ?
cheers
|
|
|
Great, thanks - I will follow the guide on here then So how about the youtube video, that wiring is totally different - should I tell him? cheers
|
|
|
|