Show Posts
|
Pages: [1] 2 »
|
well it all depends on how much W can your cards get. for example i have rx 570 where is limit 117W and despite i set anything, 900+mV it all the time hit the wall 117W and start lowering Mhz. so in this case maximum for me is 2,7xx for lyra2z (havent tried phi2). however when my card has higher W limit, im able to reach 3,1xxMhz with rx570. Which card model have lyra2z 3.1 Mhz/s hashrate ? I have RX 570 4Gb, Sapphire, Aorus, Expression, KFX all max = 2.85 I try install HiveOS, Make Gin wallet, connect to pool my 5x RX 570, and BOOM in my 750W ATX Supply... I change Supply, disconect 2 GPU , restart lyra2z GIN, on the wall 580W with 3 GPU..... i must change in settings core V to 950mV, then is 400W with 3 GPU.... I dont know how is this possible.... all GPU have bios with 950mV core..... be careful with HIVEOS and lyra2Z... PHI2 have 4.3 Mhz - RX 570 4Gb, ( PC, 3X GPU = 410W in the wall )
|
|
|
Hello! I want mine with my GPU StelliteCoin (XTL) I add coin Stellite, CryptoNight StelliteV4 , but in profit i not see this algo.....
Please for help...
|
|
|
i have 14 x rx 570 4G.. ( Auros, expedition, xfx, saphire ) All card go 30 Mhz/s
|
|
|
Can you make a priority coin ? This means, that always mine priority coin - ether, only if some other coin in group have xx % higher profit. Now mine xx% in + and -.. I want allways mine ether , only if some other coin have more then 20% more profit.
Example.... i have i group 2 pool, ether and moreno. Profit switch i set to 20%. When i start have ether higher profit so its a start with ether. Over time monero becomes 20% more profitable, so start mine monero. Profitable of monero falling down, now is profit same monero and ether...monero fall down for more19% and still mine monero not ehther!!.... me.... and in this scenario you can mine long time.. with 19% minus profit...... I hope you understand
|
|
|
any news about this site ?? Legit or scam ?
|
|
|
it's still profitable to buy Innosilicon A9 ZMaster 50 Ksol/S or is to late.... What about FORK for this coins ?
|
|
|
i try lot of sgminer version, but all sgminer work only with one gpu ( i have 5 gpu )
not AMD user myself, but check sgminer --help, my guess is something to do with --gpu-platform, or mapping. Thankyou.. I try --gpu-platform 1 , now work all 5 gpu, but hashrate is very low, jump from 500kHz to 700kHz Here is my settings..... Can you help me ? sgminer.exe -k lyra2z -o stratum+tcp://eu.bsod.pw:2159 -u GgXc......................vd -p c=GIN -I 21 --gpu-platform 1
|
|
|
i try lot of sgminer version, but all sgminer work only with one gpu ( i have 5 gpu )
|
|
|
Nobody can help me, how mine GINCOIN with AMD card ?
|
|
|
mkxminer is not for Lyra2z (GinCoin)
|
|
|
Hello !
I want mine GINCOIN (lyra2z) with AMD rx570/580 card. I try tried many settings but does not work. SGminer not start, i have error "failed to start miner process (Sgminer, Lyra2z) 1. Security or antivirus remove..... 2. Use diagnostic...." In diagnistic i see : > [15:30:17] Global quota greatest common denominator set to 1 > [15:30:17] Setting pool 0 name to GINCoin > [15:30:17] Setting pool 0 profile to AMD X-algorithm > [15:30:17] Setting pool 0 N-factor to 10 > [15:30:17] Setting pool 0 algorithm to > [15:30:17] Algorithm not found, using ckolivas. > [15:30:17] Setting profile 0 name to AMD X-algorithm > [15:30:17] Unexpected extra commandline arguments > [15:30:17] Algorithm not found, using ckolivas. > [15:30:17] Unexpected extra commandline arguments Failed to start miner process: Process has exited, so the requested information is not available. Failed to start miner in Diagnostics mode Diagnostics completed
Can you please help me ?
Can someone tell me what is hashrate LYRA2Z for RX 570 4Gb on Windows ? If i start sgminer i see only gpu0 ... ( i have 5 GPU)
|
|
|
i try with my 5x amd rx570 rig...
10 sol/s per card... then system hangup...... any help ?
|
|
|
I have started experimenting with the Profit Switching functionality, but am having an odd issue. Again I'm only doing this on a single small rig with a single 1050Ti for now until I get the kinks worked out. I have these algos configured in the profit switcher: ETH is the most profitable (and what my other 13 GPU rigs controlled by AM mines, especially the 1080Ti rigs running the ETH pill). At any rate, this test rigs starts out on ETH as expected, but after a while, it switches to one of the less profitable algos. If I then stop the rig, un-check all but Ethereum under algos and restart, I get the following error: Not sure why I would get that error. All the other rigs are happily mining away on that same pool. If I shutdown AM and restart it, it starts working again, but the same thing keeps happening. I can stop and start mining on any of the other rigs, and they don't have this error. The other rigs are also running Managed Profit Miner profiles, but only have the Ethereum algo selected atm due to this issue. I only have the NiceHash pool configured under Options/Profit Switching although I do have various other pools defined under Options/Pools. Here are some of them: I used those when I was manually switching between algos using Regular Managed Miner profiles. Could that be somehow causing the issue now that I'm using Managed Profit Miner profiles? I'm running the latest 5.2.5 version btw, including the Remote Agents. Make sure you have check in all mining software priority list in Profit profile properties
|
|
|
Pool properties --> Advanced --> Profit settings : DOT or COMMA I try set profiit to 0.7 ?? I have two rigs with same settings and same pools in group but work strange... every rig differently Must be dot or comma ( 0.7 or 0,7 ) ? Program accept both... And what means in pool group properties PRIORITY nad QUOTA ?
|
|
|
Is it possible to set profit switch threshold diferents for high limit or low ? Example.... i wannt mine ETH, if is altcoin higher 30% switch miner to altcoin...
Now i have threshold 30%, but mine altcoin even if is it 29% lower then ETH...
Thank you
I see your point, but there is currently no feature to define this - maybe it can be an improvment later on. Another option if you think some altcoin pools are less profitable than they claim, you can lower their profit factor by 30%. For the predefined pools you can set the Profit Factor to 0.7 via Options dialog, Online Services. For your own pools, you will find the same setting in the Properties of the pool, in the Advanced section. The profit switcher will then consider these pools to be 30% less profitable compared to what the claim. For now it's a good thing that the altcoins grows a lot, and then they also fall a lot ... it's not the middle like the ethereum.... Thanks for answer.....
|
|
|
Is it possible to set profit switch threshold diferents for high limit or low ? Example.... i wannt mine ETH, if is altcoin higher 30% switch miner to altcoin...
Now i have threshold 30%, but mine altcoin even if is it 29% lower then ETH...
Thank you
|
|
|
[/quote] CastXMR 1.3 and CryptoNight Saber will be included in the next development version, planned to be available within the next 1 - 2 days. [/quote] Super, Thankyou
|
|
|
PLEASE ADD BITTUBE COIN for AMD with CAST XMR.... Thankyou
|
|
|
Hi! I have very strange problem.
I have 5x rx570, windows10 and driver adrenalin 18.3.2.
1. install windows 2. install driver 18.3.2 3. patch driver 4. switch to compute mode
Whan i run Sapphire trixx get error :
During previous startup GPU-Z crashed at OpenCL detection. Please update your OpenCL and graphic driver.
I try reinstal driver , uninstall onboard intel graphic nothing !
Then i try complete format and reinstall windows 10 and still not work! Where is problem ?
This happend on my second rig, first rig have ALL same configurations and work without problem
Please for help!
Regards
|
|
|
Hi! Yesterday I run my second, this with 8x ASUS GTX1050ti Phoenix (HYNIX) , ( my first rig have 9x amd rx580 )
I was expecting 15Mh/s ETH, stock 12.3Mh/s, MemClock +250 get 13,25Mh/s
I read here that you are using MemClock +700, + 900.... I can only raise it MemClock to +250, that is 3753Mhz.. If i set to +800, memclock is still 3753 in msi afterburner, and get warrning in windows 10 - Application has been blocked from accesing Graphic hardware....
How can I solve the problem ? How much hash can I expect with this card and hynix memory ?
Thankyou for help!
My configuration - GIGABYTE GA-B250-FinTech MINING -celeron g3930 -4Gram ( 40G virtual ) -SSD120Gb -8x Asus GTX 1050Ti Phoenix -Windows 10 -Claymore dual ( SOLO MINING ETH)
|
|
|
|