I try to put S7 and S9 driver into one package. I think that it will be possible to communicate from S7 controller board with S9 hashboard. I got it up with a modified S7 driver and find out some stuff. No I try to compile it and test it. Some nearly identical functions (same name, but different params aso.) Sitting here now since yesterday  |
|
|
|
|
That´s what I was doing at moment.
Switching from the old 4.8.0 to 4.9.2 nothing else.
|
|
|
|
is this the full source code? NO! There are missing some code. Take a look at https://github.com/Zwilla/bmminerATM I merging it with cgminer 4.9.2 Stay tuned, do not try to compile atm. It will not work atm. I will send an info when I´m ready with it and got it working on my S9 machine |
|
|
|
|
Also ich kann bestätigen, sinnlos oder spam posts sind das nicht.
Rico666 ich habe mal 2 Stunden mit deinen Posts verbracht!
Coole Idee die du hast, wir müssten wohl den NSA oder die IBM Supercomputer anzapfen und wahrscheinlich einen Seetanker mit ca. 1,5 Millionen
8TB Festplatten irgendwie dort in die Nähe bringen.
Spaß beiseite!
Was willst du gerne verbogen haben?
|
|
|
|
hi together, like -ck says it is impossible to crack by a single person the bmminer. And yes bmminer is a fork of cgminer. I found some differences and some functions, but without the source code we can do nothing. - miner_thread = 4
- Built with bitmain_c5 mining support
- Waiting on sem in miner thread
- Multi Version = 1
- logging.c
- bitmain_c5_detect
- bitmain_c5_prepare
- bitmain_scanhash
- hashtest_submit
- copy_pool_stratum
- driver-btm-c5.c
- get_pic_iic
- set_pic_iic
- set_pic_voltage
- get_pic_voltage
- get_nonce2_and_job_id_store_address
- set_nonce2_and_job_id_store_address
- get_job_start_address
- set_job_start_address
- [get_QN_write_data_command/li]
- set_QN_write_data_command
- get_fan_control
- set_fan_contro
- get_hash_on_plug
- get_hardware_version
- get_fan_speed
- get_time_out_control
- set_time_out_contro
- get_BC_command_buffer
- set_BC_command_buffer
- get_BC_write_command
- get_ticket_mask
- set_ticket_mask
- get_job_id
- set_job_id
- get_job_length
- set_job_length
- get_block_header_version
- set_block_header_version
- get_time_stamp
- set_time_stamp
- get_target_bits
- set_target_bits
- get_pre_header_hash
- set_pre_header_hash
- get_coinbase_length_and_nonce2_length
- set_coinbase_length_and_nonce2_length
- get_work_nonce2
- set_work_nonce2
- get_merkle_bin_number
- set_merkle_bin_number
- get_nonce_fifo_interrupt
- set_nonce_fifo_interrupt
- get_dhash_acc_control
- set_dhash_acc_control
- get_hash_counting_number
- set_hash_counting_number
- get_all_temperature
- set_PWM_according_to_temperature
- set_frequency
- set_frequency_with_addr
- get_nonce_and_register
- read_asic_register
- check_asic_reg
- check_asic_reg_with_addr
- chain_inactive
- set_address
- software_set_address
- set_asic_ticket_mask
- set_baud
- set_baud_with_addr
- open_core
- init_uart_baud
- check_system_work
- bitmain_c5_init
- send_job
- bitmain_c5_update
- HASH2_32[7]
- /dev/axi_fpga_dev open failed
- /dev/axi_fpga_dev
- mmap axi_fpga_addr failed. axi_fpga_addr
- mmap axi_fpga_addr
- data = 0x%x, and it's not equal to HARDWARE_VERSION_VALUE
- axi_fpga_addr data = 0x%x
- /dev/fpga_mem
- /dev/fpga_mem open failed. fd_fpga_mem = %d
- mmap fpga_mem_addr failed. fpga_mem_addr = 0x%x
- mmap fpga_mem_addr = 0x%x\n"
- job_start_address_1 = 0x%x
- job_start_address_2 = 0x%x
- kmalloc for dev failed.\
- kmalloc for dev success
- ...
- ...
- and many more
here you can get my modified assembler code
https://github.com/Zwilla/bmminer-asm
|
|
|
|
What a bunch of FUD and nonsense.
Did anyone commenting in here even watch the linked video?
The OP simply forgot to click the "Using" field to change which account they want to sell from. According to the video posted, Coinbase appears to be working just fine.
I think you have no idea how selling on coinbase works! Do you really believe that I don´t know how to sell? |
|
|
|
its not been hacked. all their security works properly. i think all the inconvenience that many encounter is due to the dump of price happened on btc as of now. maybe they are are just adjusting to the price because it occurs in fast phase. but dont worry coinbase is legit company so nothing to worry. chill  Coinbase is legit? If customers can´t place orders when they want ? Is that legit? If you want cash out your bank account and the bank is all time closed is that legit? I think Coinbase is not able to handle such amount of orders! For that Coinbase is for me a dangerous platform to host my coins. They handle only one (ok two) assets and not able to handle them perfect!!! |
|
|
|
|
I was trying to sell one coin, but this message appears:
WE CANT PROCESS YOUR ORDER
|
|
|
|
|
Ohh ok, what a luck! I bought before 3 weeks some S9 for (nearly) all my coins.
Why do they sell all the coins?
|
|
|
|
Where's the cgminer source code for every version, as is required by the cgminer license.
Dear Kano, It is forked from yours! Since March 2016 https://github.com/Zwilla/cgminer |
|
|
|
Hi together, I have some features built in more. - Cgminer 4.9.2. with full customize able fan speed (hard nut) from 1% to 100%. The combination of automatic temp control = Ready for halving. Share your results, please.
- Automatic restart or reboot (Tools -> Settings)
- new Overview
- Nicehash support 100% working (not jet tested by NiceHash) see here:Antminer S7 on 4.9.2 at nicehash.com
- on Firmware page (upgrade App) NO REBOOT NEEDED!!!
- Working two weeks on Bitmain driver again!!! With Overkill Mode you got the best results now!!!
- Hardware Errors now at a minimum
- Accepted Shares nearly 100% (99,992%) possible
For those which are running Version 0026 (check Menu -> Miner -> Firmware upgrade page) _______________________________________________________________________________ _______________________________ How to update if you are running MinTorro > Version 0026- download this file Mintorro-SetpOne.tar from your customer account
- Menu -> Miner -> Firmware upgrade
- click on run this action button
- If you don´t have this button goto old style - Upload Archive
- after second reboot the system is ready for halving and it will start mining with YOUR own Pools
_______________________________________________________________________________ _______________________________ How to upgrade if you are running Old Firmware > Version 0026- download this file Mintorro-SetpOne.tar from your customer account
- Menu -> System -> Firmware upgrade
- On Menu: RESTORE CONFIG select this file
- click on upload
- after second reboot the system is ready for halving and it will start mining with YOUR own Pools
_______________________________________________________________________________ _______________________________ NEW AntMiner S7 RECOVERY SD-IMAGE - It recovers every board!How to setup SD-CARD Image?Setup now your miner- click on the menu -> Miner
- click on -> My local Miner
- activate NiceHash Mode
- fill out all other fields
- click on Make Overkill mode
- review now your settings
- click on Start Mining
- now you will be redirected to the overview Page
- reload the page if nothing happens after some seconds
Setup Intervals- click on the menu 'Tools'
- click on my Settings
- best case "activate" now Rig Update Delay to 1 Minute
- and Pools to 10 minutes (depends on your pool provider)
_______________________________________________________________________________ _______________________________ thx fubly This picture said more than 1000 words  |
|
|
|
|
Customers Question:
Any news about S5 Miners?
Answer:
If you use StepOne upgrade it will work out of the box. I have no S5 for testing but other customers where reporting it to me.
If it will not work well we / you can adjust the settings on the menu:
-> Dashboard -> Miner -> My local miner
or here
-> Dashboard -> Miner -> Cgminer.conf direct
After you made your changes, please click on "Start Mining Software" button.
At the fist time you setup your miner with MinToRRo for S5 please,
let MinerType on S7 fill all fields with your settings and click than on any "Make xxxx Mod button"
Now you can switch to AntminerType "S5" select your MHZ and click on "Make 480 Mod" button.
Then restart mining software by click on "Start Mining Software", please.
fubly
|
|
|
|
|
Dear Customer,
here are the answers for your questions.
1. My main issue now is the Old-Miner page shows version 4.8.1 and it should be 4.8.2. I need your help to fix this.
-> If you click on "Make Overkill Mod" and restart the mining software (No reboot is needed)
2. I can't seem to bring down the fans. I set them to 50% and they are still running at full speed. Do I need to reboot the Miner to set it?
-> please use UpdateApp.tar to fix that - > No reboot is needed ! -> Problem: On Cgminer.config direct you find a value "bitmain-temp", just delete this one!
Or after update just klick on "Make 480 Mod" and the line disappears.
3. Is it possible to configure the fans to auto regulate speed per desired temperature? I have tried both Fan Auto Modus on and off with no change seen.
- > This app is build in, the window where you can set it up is implemented into: -> Dashboard -> Miner -> My local Miner Menu
4. How do I view the temp control app? I click the button but I can't see how to get to the temp control app page.
- > This app is build in, the window where you can set it up is implemented into: -> Dashboard -> Miner -> My local Miner Menu
5. Is the license transferable if I sell the miner?
-> Yes - just let me know who will get the copy now and this / your customer has to open and register an account on our website Zwilla.de. After we knew
who will use your copy now we transfer it to him. On your side you have to click on the login page through the button "unregister this miner now!"
6. Does the license need to be renewed yearly or is it good for the lifetime of the Miner?
It is good for lifetime!
7. How are the SSL certs renewed when they expire?
The SSL cert is generated directly on your miner during Stepone Upgrade and it is 10 years valid.
fubly
|
|
|
|
I am at the point now where I am attempting to activate the license key so I can change to Red Z-Mod 492. Every time I login it asks me to register. When I attempt to register it says 'NO ist falsch' so something is not right. I see the following errors on the screen. The text says I have a valid license. I can't seem to find a way around this issue at the moment. The good thing is that while I figure this out, my rig is still mining with my normal settings so I am not losing anything. I wanted to note that the support provided by Michael on the support e-mail has been responsive and appreciated even with the time difference from the US.
Here are the errors I see when attempting to register my license:
Warning: unlink(/config/user_data/configs/license-active.json): No such file or directory in /www/miner-settings.php on line 212
Dear Ondart, This appears only on the SD-Card Recovery Image, because there is no login possible. Please use the SD-Image only for recovering. thx fubly p.s my personal 36 hours uptime period is now finished. I'm knocked out today. (I will respond to the next messages within 18 hours n8) |
|
|
|
I ended up booting to the SD Card and then flashing the latest Bitmain S7 Batch 7 firmware. Once I did this I was able to boot up without the Recovery SD card zwilla mod. I then re-executed the Mintorro-Setpone.tar Ugrade and it was successful this time. I was able to get into the interface and determine that it was hashing with my default values. I then successfully executed the Update procedure. My lesson learned here was to flash to the latest default firmware before executing the Update procedure. I think a comment about this should be at the beginning of the Update instructions. I am trying to configure the miner and get into 'Z-Mod 492' Red mode next. I'll post more info soon. So far so good...
Dear Ondart and to all other customers! Please! Before you upgrade or update download a new copy of StepOne and others, because I update these scripts every day and that multiple times a day. To StepOne: StepOne contains all functions to update, upgrade your miner there is no need to use the upgrade after using StepOne, because StepOne will do it all for you. So when you where using StepOne the onliest think you can run it UpdateApp.tar. UpdateApp.tar will catch the brand new Version of MinToRRo (into background) installs all and that without stop mining and without any reboot. fubly |
|
|
|
|
Show Posts
