181
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: r9 280x eth mining
|
on: July 13, 2019, 05:13:50 AM
|
r9 290/390 give 29-30 mh/s while mining on Ubuntu. For a serious increase in performance, you have to use Ubuntu version no higher than 16.04 (with new Ubuntu kernels these cards have poor compatibility). You have to install driver version 17.40 and AMD SDK kit. Switching to Linux-like OS gives additional 10 mh/s (50%). There is a guide how to do it (in Russian): https://www.cryptoprofi.info/?p=3313. Ubuntu will be useful for mining on all old cards including R9 280, 290, 295 and 390.
|
|
|
183
|
Local / Трейдеры / Re: Poloniex - биржа криптовалют
|
on: June 07, 2019, 08:00:13 PM
|
Мошенники на Полониксе кинули на 880 баксов из-за своих махинаций с монетой "Хлам". По их словам пострадало 0,4% пользователей, но их наверное намного больше.
|
|
|
185
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v14.6 (Windows/Linux)
|
on: May 31, 2019, 05:37:21 PM
|
I have about 5% increase for RX-cards, but there is no gain for old R9 290/290x (I have rig with Windows 7 with these "heaters"). There is a good increase for GTX 1080 (38 mh/s with strap 2 with 750 mV downvolting with nvidia Inspector), but R9 290/290X on the same Rig show only 20 mh/s. Is it possible to do something? They give up to 30 mh/s on small DAG-coins, but ETH and ETC have too big DAG size and AMD don't update drivers for old cards to be optimized for mining.
|
|
|
190
|
Local / Альтернативные криптовалюты / Re: [Анонс] [PoW] [PoS] VEIL - приватность без компромиссов
|
on: May 31, 2019, 05:01:14 PM
|
Сегодня пытался синхронизировать кошелек, не получилось, хотя скачал новую версию. Часть мощностей периодически кидаю на майнинг монет VEIL, потому что по калькуляторам она сейчас довольно прибыльна. Одна GTX1060 дает примерно 30 центов в день при цене за электрику около 5 центов. Кому интересен майнинг этой монеты можно почитать здесь: https://www.cryptoprofi.info/?p=3092. Расписаны все нюансы по выбору и настройке майнинга. Команда VEIL работает довольно активно, надеюсь, что они быстро исправят косяки. Ведь зачем было начинать проект, если нет сил на его развитие через несколько месяцев после старта?
|
|
|
191
|
Local / Майнеры / Re: Что проще майнить на одной карте GTX 1060
|
on: May 31, 2019, 04:56:37 PM
|
Можно попробовать майнинг криптовалюты Veil в по алгоритму x16rt. Этот алгоритм также используется в криптовалюте GIN. В настоящее время эффективный майнинг на этом алгоритме может производиться только с помощью ферм для майнинга на видеокартах. Наибольшую эффективность при этом показывают видеокарты производства компании Nvidia. Гайд по майнингу можно почитать здесь: https://www.cryptoprofi.info/?p=3092. Одна GTX1060 сейчас дает примерно 30 центов в день при стоимости электричества 5 центов за киловатт.
|
|
|
193
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: GPU Replacement fans
|
on: May 24, 2019, 10:11:19 PM
|
It is easy enough to repair damaged fans. Usually, the lubricant in the bearing connecting moving blades in the fans to the stationary stator becomes dirty and dry. This problem can be quite easily resolved after carefully removing the fan blades. This should be done by applying little lifting force upwards from opposite sides of the lower part of the blades. You need to be very careful not to break the blades and not to damage the rotor and its electronics. You can hook the blades from the bottom with two flat screwdrivers, but you need to pay attention not to damage the electronic components of the fan. After this you have to clean the area and put new lubricant. Also I'd recommend you to put miniature bearings MR52 ZZ 2x5x2.5mm instead of sliding bearing. You can study the process of repairing and modernisation of fans on pictures here: https://www.cryptoprofi.info/?p=3027.
|
|
|
194
|
Local / Майнеры / Re: Ферма не запускается. Помогите!!!
|
on: May 24, 2019, 10:01:16 PM
|
Народ, ферма на 3 1070 msi, майнер запускается, через 3 мин комп виснет, у двух видюх не крутятся кулеры (хотя должны постоянно на 70% крутиться), Кто-нибудь сталкивался с таким?
Скорее всего переразгон, либо проблемы с блоком питания. Нужно проверить логи майнера и Windows на ошибки.
|
|
|
|