s3 problem , why moving ?

[Unacceptable]

Your IP for your PC is 192.168.0.100,that is the IPV4.

Your default gateway is 192.168.0.1 (modem or router).

You need to change the miner to your subnet, 192.168.0.110 should work.The 0 is YOUR subnet,the miner is on a 1 subnet,you won't see it until you switch it to 0.Even the router/modem may not see it,but you get to it by your browser.

You will need to change your PC IP to 192.168.1.100 ,S3's default IP is 192.168.1.99.So unplug your PC ethernet from the router/modem & plug it into the miner.

Now just follow those instructions to change your PC to 192.168.1.101.

Now you can type 192.168.1.99 in a browser & change the miner to YOUR subnet,192.168.0.110(under network tab WAN section,use the edit button & save).When your done,plug the miner into your router(shut the miner off for 30 seconds & power it back up to make the changes stick).

& reset your PC to back to your subnet (192.168.0.100) & plug the ethernet back in the router.Then you should be able to type 192.168.0.110 & it should be there.

If you get a new router I'm not sure if it will be 192.168.1 or 0.Since your modem is a 0 subnet I'd assume it would still be a 0 subnet,I'm not an expert network guru.

Its is confusing,glad I never had to do it,Good Luck!!  

[notlist3d]

Your IP for your PC is 192.168.0.100,that is the IPV4.

Your default gateway is 192.168.0.1 (modem or router).

You need to change the miner to your subnet, 192.168.0.110 should work.The 0 is YOUR subnet,the miner is on a 1 subnet,you won't see it until you switch it to 0.Even the router/modem may not see it,but you get to it by your browser.

You will need to change your PC IP to 192.168.1.100 ,S3's default IP is 192.168.1.99.So unplug your PC ethernet from the router/modem & plug it into the miner.

Now just follow those instructions to change your PC to 192.168.1.101.

Now you can type 192.168.1.99 in a browser & change the miner to YOUR subnet,192.168.0.110(under network tab WAN section,use the edit button & save).When your done,plug the miner into your router(shut the miner off for 30 seconds & power it back up to make the changes stick).

& reset your PC to back to your subnet (192.168.0.100) & plug the ethernet back in the router.Then you should be able to type 192.168.0.110 & it should be there.

If you get a new router I'm not sure if it will be 192.168.1 or 0.Since your modem is a 0 subnet I'd assume it would still be a 0 subnet,I'm not an expert network guru.

Its is confusing,glad I never had to do it,Good Luck!!  

Thats assuming seller did not change it.  A lot of times it was ran with a different IP and you need to look at device list.

I know when I sold my S3's I wrote instructions for my buyers with the IP address.  Made support on ebay auctions so much easier.

[ToQcHista]

don't may ip change that change after don't working internet.


probably cause is that i have 192.168.0.1 router

[ToQcHista]

i can't click reset button.


very Clumsy place.  

[ToQcHista]

Your IP for your PC is 192.168.0.100,that is the IPV4.

Your default gateway is 192.168.0.1 (modem or router).

You need to change the miner to your subnet, 192.168.0.110 should work.The 0 is YOUR subnet,the miner is on a 1 subnet,you won't see it until you switch it to 0.Even the router/modem may not see it,but you get to it by your browser.

You will need to change your PC IP to 192.168.1.100 ,S3's default IP is 192.168.1.99.So unplug your PC ethernet from the router/modem & plug it into the miner.

Now just follow those instructions to change your PC to 192.168.1.101.

Now you can type 192.168.1.99 in a browser & change the miner to YOUR subnet,192.168.0.110(under network tab WAN section,use the edit button & save).When your done,plug the miner into your router(shut the miner off for 30 seconds & power it back up to make the changes stick).

& reset your PC to back to your subnet (192.168.0.100) & plug the ethernet back in the router.Then you should be able to type 192.168.0.110 & it should be there.

If you get a new router I'm not sure if it will be 192.168.1 or 0.Since your modem is a 0 subnet I'd assume it would still be a 0 subnet,I'm not an expert network guru.

Its is confusing,glad I never had to do it,Good Luck!!  

it ip is from router  > 192.168.0.100

[ToQcHista]

from where will guess what is s3's ip adress ?

is soft ?

[notlist3d]

i can't click reset button.


very Clumsy place.  

Make sure you have tried to find it before you reset it.   But if you have to reset you will need to use a paperclip or pen to hit the button in most cases, and make sure you read how to do it properly.

[ToQcHista]

i can't click reset button.


very Clumsy place.  

Make sure you have tried to find it before you reset it.   But if you have to reset you will need to use a paperclip or pen to hit the button in most cases, and make sure you read how to do it properly.

i everithing try . needle, paperclip other 

but i may once click button , long time can't click .

other way don't exist ?

from where i know what ip have s3 ?
i don't want it reset button

[ToQcHista]

now right again red and gren LED is why /?

before was only green .


first testing was . green and red LED

[notlist3d]

i can't click reset button.


very Clumsy place.  

Make sure you have tried to find it before you reset it.   But if you have to reset you will need to use a paperclip or pen to hit the button in most cases, and make sure you read how to do it properly.

i everithing try . needle, paperclip other 

but i may once click button , long time can't click .

other way don't exist ?

from where i know what ip have s3 ?
i don't want it reset button

You have to do a certain way with reset.  Search reset on this page - https://bitcointalk.org/index.php?topic=697474.0

Keep in mind your miner did break a metal fin in shipping so we still cannot say if it somehow was damaged from a hard hit.   Or if following this will help.

[ToQcHista]

Write you step how to will make everything for internet ?


First. I need tp link router after ?

[ToQcHista]

This red and green with led dont jo problem ?
Anyway enter Ip on adress ?

[notlist3d]

Write you step how to will make everything for internet ?


First. I need tp link router after ?

You will need to have a router just to split the internet connection to go to multiple items.  It does not have to be a tp link brand for your S3.

Did you reset your S3? Or is it still in state shipped from seller?

[ToQcHista]

 
I can't understolad ((

I that will buy tp router after connect s3 after and just enter on ip ?

I cant click reset button

[mavericklm]

if you don't have empty socket on your router then you need a switch!

http://3.bp.blogspot.com/_Z1HeAcn8Ok4/TD7w0fKRj5I/AAAAAAAAAZE/ySJb64B33Z4/s1600/imagesrrrr.jpg

buy switch if no socket on router

reset miner

open browser and go to 192.168.1.99

[ToQcHista]

if you don't have empty socket on your router then you need a switch!

http://3.bp.blogspot.com/_Z1HeAcn8Ok4/TD7w0fKRj5I/AAAAAAAAAZE/ySJb64B33Z4/s1600/imagesrrrr.jpg

buy switch if no socket on router

reset miner

open browser and go to 192.168.1.99

I dont want switch .
Tp link that buy after free enter on ip ?

Red and green led is problem ?

[ToQcHista]

Now that with red and grreen led that is ,how to make reset , i that wilL click after should light only red and two colo is on s3

[ToQcHista]

I dont want reset button


I that will use ip scaner really search s3's ip ?

[ToQcHista]

my s3 that hav red light , anyway enter browser s3 website ?


i before try tenda router and don't showed in" ip scanner" s3 IP 

[ToQcHista]

i try reset button but the result don't know  is ?

https://www.youtube.com/watch?v=1Clg1K6ndlk