Stack37 (OP)
Newbie
 Offline
Activity: 7
Merit: 0
|
 |
August 30, 2016, 07:58:05 AM
Last edit: August 30, 2016, 08:21:10 AM by Stack37 |
|
Hello! Died 5 cards rx 480 ref(xfx, gyga, 2 powercolor, his) After downloading Windows error thread stuck in device driver. All 5 of the graphics card died in the first 24 hours. The remaining 30 pieces of work from a week to a month. All the cards worked on the same settings. GPU 1130mhz 900mv, memory 2200mhz 900mv. Mining only eth. Flashed the Bios, only the timings. 2 of 5 dead cards were not flashed. Visible damage no. In safe mode is determined (disabled drivers are also). Could it be because of settings?(Chip 1130mhz 900mv, memory 2200mhz 900mv) The monitor sees this picture. https://pp.vk.me/c604329/v604329301/29def/TAWP1MMW2HI.jpgGpu-z other working card on screen. http://dl1.joxi.net/drive/2016/08/30/0008/1579/542251/51/43c407dbf2.jpg |
|
|
|
|
|
|
|
|
|
|
|
|
|
There are several different types of Bitcoin clients. The most secure are full nodes like Bitcoin Core, but full nodes are more resource-heavy, and they must do a lengthy initial syncing process. As a result, lightweight clients with somewhat less security are commonly used.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
|
Redrose
|
|
August 30, 2016, 08:28:02 AM |
|
First, they're very hot. Also, did you tried to reinstall Windows ? On a bad quality HDD, when I turned off the system, I would block like you. If you find this too painful, you can also try to run the GPUs in another rig, since you have several. All of this is to make sure that they're really dead.
Did you downclocked or overclocked it ?
|
|
|
|
|
mikhan
Member
Offline
Activity: 84
Merit: 10
|
|
August 30, 2016, 08:29:07 AM |
|
they just die, replace it by warranty
|
|
|
|
|
Stack37 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
August 30, 2016, 08:47:12 AM |
|
First, they're very hot. Also, did you tried to reinstall Windows ? On a bad quality HDD, when I turned off the system, I would block like you. If you find this too painful, you can also try to run the GPUs in another rig, since you have several. All of this is to make sure that they're really dead.
Did you downclocked or overclocked it ?
GPU 1130mhz 900mv, memory 2200mhz 900mv This is 100% not bad hdd. Cards died 5 graphics cards died in different configurations and in no way related. Different power supplies, different sdd drives. All died in the first 24 hours of mining. |
|
|
|
|
|
eretron
|
|
August 30, 2016, 10:53:40 AM |
|
Interesting, I got 1 died yesterday with same error as yours... It was Sapphire 480 Reference model...
Exactly the same behaviour as yours...
My all GPUs run at 65-70c max, so its not a temp issue...
EDIT: Card died after 5 days of mining
|
|
|
|
Q_R_V
Sr. Member
Offline
Activity: 428
Merit: 250
Inactivity: 8963
|
|
August 30, 2016, 11:03:11 AM |
|
More info about motherboard and risers please. Were cards connected directly to the mobo or through risers (what kind of risers, molex connector, berg connector)?
|
|
|
|
|
|
|
|
eretron
|
|
August 30, 2016, 12:55:27 PM |
|
Yup. Same here
H81 btc asrock, connected via USB Riser, 750W cooler master PSU.
This rig had 3x rx480 undervolted to:
800mA@1000mhz core clock with mem clocked at 2000
GPU Had artifacts on half of the screen when conected to monitor via hdmi. And with that card connected winodws eould always celrash during boot. RMAed waiting for replacement card to return.
|
|
|
|
Stack37 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
August 30, 2016, 01:00:59 PM |
|
Yup. Same here
H81 btc asrock, connected via USB Riser, 750W cooler master PSU.
This rig had 3x rx480 undervolted to:
800mA@1000mhz core clock with mem clocked at 2000
GPU Had artifacts on half of the screen when conected to monitor via hdmi. And with that card connected winodws eould always celrash during boot. RMAed waiting for replacement card to return.
Maybe the reason downvolt? I have 30 pieces of work from a week to a month. How many cards do you have? |
|
|
|
|
|
eretron
|
|
August 30, 2016, 01:08:49 PM |
|
9pcs
|
|
|
|
philipma1957
Legendary
Offline
Activity: 4102
Merit: 7764
'The right to privacy matters'
|
|
August 30, 2016, 02:13:25 PM |
|
both of you have risers on the dead cards am I correct?
I have 20 cards all good all have no risers.
My guess is it is a riser issue.
|
|
|
|
|
|
zcrewsmok
Newbie
Offline
Activity: 7
Merit: 0
|
|
August 30, 2016, 02:37:51 PM |
|
I have 20 cards all good all have no risers.
Number of rigs should be under 20 cards? What motherboard? |
|
|
|
|
|
eretron
|
|
August 30, 2016, 03:18:00 PM |
|
Yes. Default timings. All settings were done in wattmann with stock BIOS on all cards. |
|
|
|
|
Redrose
|
|
August 30, 2016, 06:29:08 PM |
|
both of you have risers on the dead cards am I correct?
I have 20 cards all good all have no risers.
My guess is it is a riser issue.
So funny Phil, this attack against risers  . Though I'll listen to you for my next rig, by not using any riser and placing all the cards on a motherboard, for now all my cards except two cards are connected throught risers and I never had any problem. |
|
|
|
|
|
Cryptozillah
|
|
August 30, 2016, 06:38:30 PM |
|
As long as you run one riser per powerline you should be ok, two per powerline is a 100% fail, just a question about when it is time for a meltdown.
I now run my rigs with 4 x 480 (custom bios 30.5Mhs/gpu) on H81 BTC Pro boards, one riser per rail and they dont get that hot.
|
|
|
|
|
|
eretron
|
|
August 30, 2016, 06:49:19 PM |
|
The riser was the only thing powered from that powerline so that's not an issue.
BTW nothing was melted or eaven hot to touch.
|
|
|
|
reb0rn21
Legendary
Offline
Activity: 1896
Merit: 1024
|
|
August 30, 2016, 07:16:01 PM |
|
If the screen have "garbage" and GPU is booting up, defo its a memory problem
Could be a bad batch of memory used, try to find out which memory was used on those cards, there were reports on bad batch of micron chips with MSI Gaming X 1070 card, they were canceled
I had one MSI gaming 1070 die on my, but it just blown up, prolly VRM dies, bad components
|
|
|
|
|
Ambros
|
|
August 30, 2016, 07:20:12 PM |
|
If the screen have "garbage" and GPU is booting up, defo its a memory problem
Could be a bad batch of memory used, try to find out which memory was used on those cards, there were reports on bad batch of micron chips with MSI Gaming X 1070 card, they were canceled
I had one MSI gaming 1070 die on my, but it just blown up, prolly VRM dies, bad components
They replace that kind of failure on warranty ? |
|
|
|
|
B1tUnl0ck3r
Sr. Member
Offline
Activity: 854
Merit: 277
liife threw a tempest at you? be a coconut !
|
|
August 30, 2016, 07:27:51 PM |
|
both of you have risers on the dead cards am I correct?
I have 20 cards all good all have no risers.
My guess is it is a riser issue.
Good hypothesis... but still not a good news. Thank you very much for sharing OP. the reliability issue is very important... And it seems that the issue is more widespread than I expected  . |
When the people of the world will get that covid was intentionally released to frame china, steal the election from trump, assure massive bail outs and foster the forced vaccination agendas...they will forget, like 911, wmds in irak, uss liberty or pedogate.
|
|
|
tytanick
Legendary
Offline
Activity: 2660
Merit: 1096
Simplemining.net Admin
|
|
August 31, 2016, 09:01:41 AM |
|
let me ask stupid two questions:
cards not "died" but you see only artifacts right ?
did you trued to restore original bios ? - is the problem still presists ?
also those ribbon risers are very bad in all cards.
I am bying only USB risers - they are the best.
|
|
|
|
Stack37 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
August 31, 2016, 09:28:16 AM |
|
let me ask stupid two questions:
cards not "died" but you see only artifacts right ?
did you trued to restore original bios ? - is the problem still presists ?
also those ribbon risers are very bad in all cards.
I am bying only USB risers - they are the best.
Cards do not work with the drivers, BSOD "error thread stuck in device driver" BIOS restored to stock using atiwinflash |
|
|
|
|
tytanick
Legendary
Offline
Activity: 2660
Merit: 1096
Simplemining.net Admin
|
|
August 31, 2016, 09:29:15 AM |
|
it might be software issue ?
like card bios issue ?
|
|
|
|
Stack37 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
August 31, 2016, 10:25:43 AM |
|
it might be software issue ?
like card bios issue ?
no, I don't think because of this |
|
|
|
|
|
joaocha
|
|
August 31, 2016, 12:38:07 PM |
|
it might be software issue ?
like card bios issue ?
no, I don't think because of this i have this kind of artifcacts using risers,with 1 gpu it boots up, when i tried 2 or more this kind of bug appears and windows freezes ( tried ethos same error) try plugin only one gpu to motherboard direct, without risers It worked for me And looking your riser, i think you should plug only one 12v rail, the 4 pin one, not the 6 pin |
|
|
|
|
Stack37 (OP)
Newbie
Offline
Activity: 7
Merit: 0
|
|
August 31, 2016, 01:38:50 PM |
|
it might be software issue ?
like card bios issue ?
no, I don't think because of this i have this kind of artifcacts using risers,with 1 gpu it boots up, when i tried 2 or more this kind of bug appears and windows freezes ( tried ethos same error) try plugin only one gpu to motherboard direct, without risers It worked for me And looking your riser, i think you should plug only one 12v rail, the 4 pin one, not the 6 pin Put in different systems with different OS, without a riser |
|
|
|
|
|
joaocha
|
|
August 31, 2016, 02:01:14 PM |
|
Doe it boot on security mode? without any display bug?
|
|
|
|
|
|
eretron
|
|
August 31, 2016, 03:06:50 PM |
|
It has artifacts even in BIOS. So it's not OS related.
|
|
|
|
leonix007
Sr. Member
Offline
Activity: 1008
Merit: 297
Grow with community
|
|
September 01, 2016, 01:29:07 AM |
|
I am using 4 Ribbon risers applied with my 4 GPUs, the risers are not powered and working fine as of the moment. cross finger not to experience this one.  |
|
|
|
|
|
