ymer (OP)
|
|
May 09, 2013, 05:10:14 AM |
|
Got my first valid block after 14 hours of mining.
25:1 rate
|
|
|
|
|
|
|
|
|
Unlike traditional banking where clients have only a few account numbers, with Bitcoin people can create an unlimited number of accounts (addresses). This can be used to easily track payments, and it improves anonymity.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
Mhash pipe
Member
Offline
Activity: 70
Merit: 10
|
|
May 09, 2013, 05:19:42 AM |
|
2 orphans, 0 accepted,
8 hours mining...
|
|
|
|
96redformula
|
|
May 09, 2013, 05:36:47 AM |
|
About 18 hours mining. I have nothing special other than 3550k using built in miner w/ command line I am at about 45 confirmed blocks w/ about 8 orphans. I am surprised I am still finding blocks, just did two in the last 2 hours.
My guess is that you guys have something setup wrong. Just use the QT file loaded up from CMD prompt and set the numbers of threads right. Same as the instructions on the first YaCoin Page.
|
|
|
|
ymer (OP)
|
|
May 09, 2013, 05:37:55 AM |
|
About 18 hours mining. I have nothing special other than 3550k using built in miner w/ command line I am at about 45 confirmed blocks w/ about 8 stales. I am surprised I am still finding blocks, just did two in the last 2 hours.
Are you in europe?
|
|
|
|
Mhash pipe
Member
Offline
Activity: 70
Merit: 10
|
|
May 09, 2013, 05:53:52 AM |
|
well, i'll tell you this, i just removed the addnode crap from the bat file and I now have 11 connections as opposed to the 8 I had previously...
EDIT: up to 25 a few minutes later and growing
|
|
|
|
96redformula
|
|
May 09, 2013, 05:55:04 AM Last edit: May 09, 2013, 06:09:22 AM by 96redformula |
|
About 18 hours mining. I have nothing special other than 3550k using built in miner w/ command line I am at about 45 confirmed blocks w/ about 8 stales. I am surprised I am still finding blocks, just did two in the last 2 hours.
Are you in europe? No, Southwest USA. Here, I posted this on the other thread. ********************************************************* I have had such great luck following directions on the OP, and I mean a whole lotta luck. Download Windows files from MEGA. Unzip Run QT and let it update. Close QT Open up CMD prompt and move to the location of the QT executable using cd command. Use Command for windows give on OP, modify genproclimit for # of threads. Code Below: yacoin-qt -gen -genproclimit=1 -addnode=82.211.30.212 Sit back and let it find blocks.
|
|
|
|
Xanthe
Member
Offline
Activity: 72
Merit: 10
|
|
May 09, 2013, 05:55:49 AM |
|
It's really unfortunate that there were/are so many problems with orphans. I started off trying the Windows client but I was getting only orphans and very few at that. So then I started up Linux in VirtualBox and compiled the Yacoin-qt client and ran it with the following command: ./yacoin-qt -gen -genproclimit=6 -addnode=82.211.30.212 I got a surprising number of blocks and had only a ~10% orphan rate. I don't know why the Linux version seemed to work so much better (and in a VM, too!). As for location, I'm in the US. My ping to the 82.211.30.212 node is 120ms.
|
|
|
|
sidelsky18
Newbie
Offline
Activity: 56
Merit: 0
|
|
May 09, 2013, 06:28:52 AM |
|
Been mining for around 9 hours now. 3 accepted blocks and 3 orphaned blocks, so approximately 1 block every 90 minutes.
|
|
|
|
96redformula
|
|
May 09, 2013, 06:31:29 AM |
|
Been mining for around 9 hours now. 3 accepted blocks and 3 orphaned blocks, so approximately 1 block every 90 minutes.
That comes out to ~450 coins / day assuming nothing changes. I would say that is perfectly reasonable.
|
|
|
|
tacotime
Legendary
Offline
Activity: 1484
Merit: 1005
|
|
May 09, 2013, 06:34:09 AM |
|
It's really unfortunate that there were/are so many problems with orphans. I started off trying the Windows client but I was getting only orphans and very few at that. So then I started up Linux in VirtualBox and compiled the Yacoin-qt client and ran it with the following command: ./yacoin-qt -gen -genproclimit=6 -addnode=82.211.30.212 I got a surprising number of blocks and had only a ~10% orphan rate. I don't know why the Linux version seemed to work so much better (and in a VM, too!). As for location, I'm in the US. My ping to the 82.211.30.212 node is 120ms. 64-bit compiler. On 2700K I get 400 KH/s
|
XMR: 44GBHzv6ZyQdJkjqZje6KLZ3xSyN1hBSFAnLP6EAqJtCRVzMzZmeXTC2AHKDS9aEDTRKmo6a6o9r9j86pYfhCWDkKjbtcns
|
|
|
LOG123
Full Member
Offline
Activity: 153
Merit: 100
...
|
|
May 09, 2013, 10:57:00 AM |
|
Only a few can mine this shit, i try whit my 3 xeons and 2 FX-8 (900 khs) and only find 1 block and hundreds orphans in 11 hours, I configure properly the client and mi connection. Man !!! q6600 382 yac amd A8 ran for ~30 min 41 yac problem, officer?
|
|
|
|
xibeijan
Legendary
Offline
Activity: 1232
Merit: 1001
|
|
May 09, 2013, 10:57:54 AM |
|
point of this thread please Google orphan block. I was getting about 1 block every 3 minutes at the start, now I get one around every hour. +1 There are obviously a lot of noobs here.
|
|
|
|
hercules
Newbie
Offline
Activity: 30
Merit: 0
|
|
May 10, 2013, 05:31:59 PM |
|
I get more or less a 5:1 ratio of orphans:generations... is it normal?
Can you please help with some settings?
|
|
|
|
|