Krnlx Nvidia xevan miner - 3.3+ mh on 1070, ~6mh on 80ti FREE, OPENSOURCE

[car1999]

can i build it against cuda9 and copy the binary to rigs with only cuda8 installed? does it run slower than  cuda9 rig?

All you need is recent Nvidia driver with CUDA9 support, you won't need any toolkits installed.

Great, thanks. Does the CPU of build machine matter? I have G1840, g3900 ,g4560, e3 1231, which one is better to build the binary and copy to other rig with different CPU?

I use ubuntu 16, nvOC.

For *nix it will be a problem (running without reboot), if you already have recent drivers installed, you can ask someone to build binary for you and just update, but if you need to update driver or want to install toolkit and build from scratch - as I know you'll need to reboot at least 1 time. If access is only remote it's quite risky, especially regarding driver module update.

CPU matters, so if you want to build it for all variety of hardware you need to remove "-march=native" flag from configure.sh file.

P.S: I'm not so experienced in *nix, it's just what I remember

I checked the document of gcc, removing arch=native can lead performance losses, so I think build  against the weakest g1840 is fine.

[1715447618]

1715447618

[1715447618]

1715447618

[UrsaUrsa]

where to find the 9.0 binary?

https://mega.nz/#F!RtYS0KwY!FGxr0uBWo1nZBSqBWkFx0w


CUDA 9 built project, feel free to test. Start with intensity 18.

So weird that the one on github does not get flagged up as a virus but this one does? (false positive, I know)

[stzcze]

Good job!!! Thx

1060 tdp 70 core +150 mem -500

13,66 6x1060 6gb -i 21

latest driver, x86 cuda 9 build, w10

[palgin]

where to find the 9.0 binary?

https://mega.nz/#F!RtYS0KwY!FGxr0uBWo1nZBSqBWkFx0w


CUDA 9 built project, feel free to test. Start with intensity 18.

So weird that the one on github does not get flagged up as a virus but this one does? (false positive, I know)

It's packed, so it gets flagged.

[UrsaUrsa]

where to find the 9.0 binary?

https://mega.nz/#F!RtYS0KwY!FGxr0uBWo1nZBSqBWkFx0w


CUDA 9 built project, feel free to test. Start with intensity 18.

So weird that the one on github does not get flagged up as a virus but this one does? (false positive, I know)

It's packed, so it gets flagged.

I'm obviously not questioning your integrity but found it a bit strange. Is the one github not packed? Have you introduced a fee by any chance? Thanks for your time.

[startsts]

Maximum result that I could get,  seems very profitable 

GPU#0:MSI GTX 1060 3GB, 2178.23kH/s

[Vivik]

CUDA 9.0 x86 - 8x1070 28Mh

[brownfly]

anybody can tell me what I am doing wrong?
When I start the miner with altminer config like this:

Code:

ccminer_x86 -a xevan -o stratum+tcp://eu1.altminer.net:3739 -u Vo...Z -p c=VSX
Windows 10

it always gives me an error message:

Code:

[2017-10-06 13:59:06] Starting on stratum+tcp://eu1.altminer.net:3739
[2017-10-06 13:59:06] NVAPI GPU monitoring enabled.
[2017-10-06 13:59:06] 6 miner threads started, using 'xevan' algorithm.
[2017-10-06 13:59:07] Stratum authentication failed
[2017-10-06 13:59:07] ...retry after 30 seconds

WTF??? coin code is correct, wallet address is correct, startum address is correct, so why it complains???

[stzcze]

Gigabyte GTX 1080 Ti, 5243.33kH/s
Gigabyte GTX 1080, 3855.18kH/s

cuda 9 build x86

tdp 65 -i 21

[UrsaUrsa]

Gigabyte GTX 1080 Ti, 5243.33kH/s
Gigabyte GTX 1080, 3855.18kH/s

cuda 9 build x86

tdp 65 -i 21

cude 9 build x86 (thank god for windows defender...)

tdp 73 -i 21

5x 1070 @ 15.28Mh/s

[Vorona34]

Maximum result that I could get,  seems very profitable 

GPU#0:MSI GTX 1060 3GB, 2178.23kH/s

Long works? I have a miner inevitably die after 1 minute or after 5 , depending on the intensity. Dropped to 14 could not wait for fall, but normal speed not seen )))

[arity]

On linux with CUDA 9 & compile with sm61, 6x1080ti (each power limit 170w) reported hash rate is 30Mh/s. Default intensity.

According to whattomine that hash rate should yield about 1.47 BSD per hour, but the actual shown on pool earning is only 0.8 BSD. Tested on suprnova pool.

[th3.r00t]

anybody can tell me what I am doing wrong?
When I start the miner with altminer config like this:

Code:

ccminer_x86 -a xevan -o stratum+tcp://eu1.altminer.net:3739 -u Vo...Z -p c=VSX
Windows 10

it always gives me an error message:

Code:

[2017-10-06 13:59:06] Starting on stratum+tcp://eu1.altminer.net:3739
[2017-10-06 13:59:06] NVAPI GPU monitoring enabled.
[2017-10-06 13:59:06] 6 miner threads started, using 'xevan' algorithm.
[2017-10-06 13:59:07] Stratum authentication failed
[2017-10-06 13:59:07] ...retry after 30 seconds

WTF??? coin code is correct, wallet address is correct, startum address is correct, so why it complains???

Did you set the intensity manually?

UPD. For 1060 cards intensity sets up incorrectly - you must adjust it with -i param. -i 20 is best for 1070, 1080ti

As far as I see the answer is no. There may be your problem.

[buzzkillb]

1080 hashrate. not ti.

Code:

[S/A/T]: 0/151/151, diff: 0.065, 3794.39kH/s yes!
[S/A/T]: 0/152/152, diff: 0.020, 3794.27kH/s yes!
GPU#0:EVGA GTX 1080, 3799.83kH/s

[integrale]

Your great Work resulted :

Xubuntu 16.04 LTS
Cuda 9
Nv 384.90
i=20.25

Code:

[2017-10-06 22:35:34] GPU#0:NONCE FOUND 
[2017-10-06 22:35:34] GPU#0:MSI GTX 1050, 1113.18kH/s
[2017-10-06 22:35:34] GPU#0:MSI GTX 1050, 0.018MH/W, 0.00063MH/Mhz
[2017-10-06 22:35:34] GPU#0:MSI GTX 1050, 62C(F:56%) 1766/3504MHz(63W)
[2017-10-06 22:35:34] GPU#0:target 0 22c92492 1c9
[2017-10-06 22:35:34] GPU#0:target 1c922c92492
[2017-10-06 22:35:34] [S/A/T]: 0/78/80, diff: 0.004, 1110.65kH/s yes!

thx Guys for The Miner

[blackhorse7]

Windows x64 version, EVGA GTX 1060 + 80 / + 500 / 84% tdp (I didnt change intensity, worked on default = 20): 2240kh/s in benchmark mode.
It works, thank you

[buzzkillb]

It's alexis78 base, optimised for cuda 7.5, so it should be faster. Try x86 build, it's generally faster in CUDA8 not specifically optimised case, or build your own binaries, experiment 

No, I love those wattage and temp monitoring in x64 builds so x86 build is not for me ))
And my binary is only 20mb ... yours is 37 ... why?

How do you check wattage and temp on ccminer?

[brownfly]

Did you set the intensity manually?

UPD. For 1060 cards intensity sets up incorrectly - you must adjust it with -i param. -i 20 is best for 1070, 1080ti

As far as I see the answer is no. There may be your problem.

yes, I did:

ccminer -a xevan -i 20 -o stratum+tcp://eu1.altminer.net:3739 -u Vo...Z -p c=VSX

the same result. I use 1070.

Update: something wrong with my wallet. If I use the wallet id from any recorded transaction, it works! but any addresses from my wallet - they look like invalid for the pool. Any ideas???
I use VSYNC wallet v1.2.3.0-g32a928e

Update: crap, apparently there are two VSYNCs! Downloaded another VSync v 1.0.0.1 and synchronizing...

[spider703]

where to find the 9.0 binary?

https://mega.nz/#F!RtYS0KwY!FGxr0uBWo1nZBSqBWkFx0w


CUDA 9 built project, feel free to test. Start with intensity 18.

hi, i runing your miner on algo myriadgroestl, he gives me 3 Gh and no seach blocks

[brownfly]

finally... the wallet has been synchronized and the miner does work. 6 x 1070 ~ 20 MH/s
Profitability is about like for BTX/VIVO. Not too bad, but still less than my favorite coin