Innosilicon A4+ setup tutorial

[ilostmyface]

Maybe someone can help me brainstorm on an issue. I have a A4+ that had 1 chain down day after arrival from Inno. Board would light up green then the light would go out after bootup. Board never hashes. After trying to swap data cables/PSU/firmwares/data ports nothing resolved the issue. I contacted Inno and had the board sent in under warranty and they replaced the board. After swapping the board all 4 boards worked for a few days. Now the exact same board from Inno is having the same issue. Very odd...

[OKorator]

what a huge f u from innosiicon.

price for an a4+ is now 1180 usd.

bought for 3200; resale value gone!

[stianeggum]

Ye they are so smart over there at Innosilicon...

I ordered 10 a5s in the new year promotion, payed 30k usd total. and they sent me an mail 2 weeks after the purchase asking me if i wanted to buy a5+ for 4200 each or more A5s for 2100.


21 of may Innosilicon gave me a price that was gonna compensate the pricedrop for the A5 purchase for: A4+ with psu 1900 usd, and now they are selling them for 1180+120 usd for psu, how fucking rude?!?

These people are the worst kind.

[yamada-tech]

Hi,

I'm thinking of mining altcoin.
Could mining to the local Wallet ?

[A4+ IP] 192.168.1.254
[Wallet innstalled PC IP] 192.168.1.60

[setting1] can not
URL 192.168.1.60:port
Waler user
Pass x

[setting2] can not
URL http://192.168.1.60:port
Waler user
Pass x

 

[needed357]

awesome miner is showing me x100 more HW error than the miner local page?

wtf??

awesomer miner HW ERROR: 519
miner local page: none 0!

[RoosterVT]

Good Morning,
I have one hashing board that the green LED goes off after reboot. How are the boards identified by the control board? I did a dmesg from CLI and not sure what to look for. I figure that if all boards are present in dmesg I should be able to see them there. Are there any onboard diag commands I can run?

Regards,

[BobbyMartin]

I don't know what to try anymore.

I had been running on AwesomeMiner, but it never really worked that well. I'd tell it to switch pools and it would just stayed 'Dead' or 'Disabled'.

Yesterday all 10 of my A4+s got stuck in a boot loop. I can telnet. I can log in. I can reboot, change config, upload new firmware. I can do almost anything... Except it never connects to a pool. It just reboots over and over and all I see are the spinning wheels on the status page. Currently trying to connect to prohashing.

[shepardblue]

I don't know what to try anymore.

I had been running on AwesomeMiner, but it never really worked that well. I'd tell it to switch pools and it would just stayed 'Dead' or 'Disabled'.

Yesterday all 10 of my A4+s got stuck in a boot loop. I can telnet. I can log in. I can reboot, change config, upload new firmware. I can do almost anything... Except it never connects to a pool. It just reboots over and over and all I see are the spinning wheels on the status page. Currently trying to connect to prohashing.

I had a problem like that with one of my machines and it turned out to be that the machine was not getting enough power. I move the machine to another circuit and it worked fine.

[BobbyMartin]

That's definitely not the case.

I ended up pointing them to miningpoolhub for the moment. Putting that in and then doing a reboot seemed to fix it. How on earth am I supposed to get AwesomeMiner to work for me? It took all of my miners offline.

Any time I try to set up a new pool profile to switch my ASICs over, the pool just says "dead". I want to solo mine verge on Prohashing or securepayment but this program just doesn't seem to like it.

[omshree]

I changed to --api-listen --api-network --api-allow W:0/0  ,and still AM cannot see the miner

[Jroc561]

May have bricked my miner, as soon as power is turned on the fault light illuminates red. No LEDs elsewhere, no fan movement. It does run while the reset button is pushed in, well at least the fans click on, will try to have someone push down the reset button while I attempt to log into the miner console later.

(Tried switching the PSU, No IP is being registered on the router when connecting directly via ethernet)

No TF reader.

May have to send it in or perhaps score a controller second hand...... any other ideas. Wish there was a foolproof hard reboot button like a push in reset for 10-15seconds...

[persocra]

May have bricked my miner, as soon as power is turned on the fault light illuminates red. No LEDs elsewhere, no fan movement. It does run while the reset button is pushed in, well at least the fans click on, will try to have someone push down the reset button while I attempt to log into the miner console later.

(Tried switching the PSU, No IP is being registered on the router when connecting directly via ethernet)

No TF reader.

May have to send it in or perhaps score a controller second hand...... any other ideas. Wish there was a foolproof hard reboot button like a push in reset for 10-15seconds...

The exact same thing happened to mine. I'm trying to connect via serial cable and figure something out, but please let me know if you come up with something. Innosilicon charges USD 150 + shipping for a new control board, but I'll give the serial cable a go first.

[Jroc561]

May have bricked my miner, as soon as power is turned on the fault light illuminates red. No LEDs elsewhere, no fan movement. It does run while the reset button is pushed in, well at least the fans click on, will try to have someone push down the reset button while I attempt to log into the miner console later.

(Tried switching the PSU, No IP is being registered on the router when connecting directly via ethernet)

No TF reader.

May have to send it in or perhaps score a controller second hand...... any other ideas. Wish there was a foolproof hard reboot button like a push in reset for 10-15seconds...

The exact same thing happened to mine. I'm trying to connect via serial cable and figure something out, but please let me know if you come up with something. Innosilicon charges USD 150 + shipping for a new control board, but I'll give the serial cable a go first.

I hate that you are going through the same thing but I’m glad I have at least one mind trying to solve the issue

[BabylonTreker]

What is a good temp to try and maintain? I feel like mine are running to hot but I'm new to mining.

[AltcoinScamfinder]

If someone wants to make a DHCP enabled stock latest version of the A4 firmware (SD Image) I will send you $200 in crypto of your choice. If you don't want it public you can DM.

Please and thank you.

[tchor66]

Hello, I sell 4 miners A4 + and also 2 miners A8 +
make Offer
thank you

[Bitreo]

Hi Guys,

sorry but not sure if has been mentioned here but does anyone have the API access details for the Innosilicon D9 miners ?

Regards,

[shadowelite]

hi I need some help
I got an a4+ g19 and one board went down
so I downgraded firmware working fine all 4 worked,
changed pools a few days later and it came up with 3 boards again
so i reflushed as image and now i have issue
i cant re flush any image even latest one
its stuck on 15%
also in the settings it says its g9 but before it said g19 and board says g19
any ideas?
only flushed .bin , no sd card slot on mine
can i flash via telnet?
thanks

[spfan]

I really need some help here!  I have 2 Innosilicon A4+ miners.  My router died a couple weeks ago.  I've since replaced it with a new one but neither miner will hash.  I can get to all of the pages in the Miner Status interface, input the mining pool and username/password, etc.  But when I go to the Miner Status page it just spins the "thinking" symbols forever.  Confirmed through the mining pool that it isn't hashing.  There are no fault lights, i've updated the firmware, I'm out of ideas and/or skills and need help.  Please and Thank You!

[mvelikov]

Hello, I saw the post is about Innosilicon A4+, buy I can't find such one for Innosilicon D9.

I have 2 Innosilicon D9 opened to Internet  (Yes, I know that this is a bad idea) since yesterday when 1 of the miner starts mining for someone else. The password was changed and I cannot login to the miner. Now I am trying to hard reset (reset the firmware) to its defaults. I am trying to to the tutorial from this post, but it is not working for D9. I can connect via PuTTy wit miner IP + port 22 and SSH, but the username and/or password is incorrect. Any suggestions?