Innosilicon A4+ setup tutorial

[BabylonTreker]

What is a good temp to try and maintain? I feel like mine are running to hot but I'm new to mining.

[1714869928]

1714869928

[1714869928]

1714869928

[1714869928]

1714869928

[AltcoinScamfinder]

If someone wants to make a DHCP enabled stock latest version of the A4 firmware (SD Image) I will send you $200 in crypto of your choice. If you don't want it public you can DM.

Please and thank you.

[tchor66]

Hello, I sell 4 miners A4 + and also 2 miners A8 +
make Offer
thank you

[Bitreo]

Hi Guys,

sorry but not sure if has been mentioned here but does anyone have the API access details for the Innosilicon D9 miners ?

Regards,

[shadowelite]

hi I need some help
I got an a4+ g19 and one board went down
so I downgraded firmware working fine all 4 worked,
changed pools a few days later and it came up with 3 boards again
so i reflushed as image and now i have issue
i cant re flush any image even latest one
its stuck on 15%
also in the settings it says its g9 but before it said g19 and board says g19
any ideas?
only flushed .bin , no sd card slot on mine
can i flash via telnet?
thanks

[spfan]

I really need some help here!  I have 2 Innosilicon A4+ miners.  My router died a couple weeks ago.  I've since replaced it with a new one but neither miner will hash.  I can get to all of the pages in the Miner Status interface, input the mining pool and username/password, etc.  But when I go to the Miner Status page it just spins the "thinking" symbols forever.  Confirmed through the mining pool that it isn't hashing.  There are no fault lights, i've updated the firmware, I'm out of ideas and/or skills and need help.  Please and Thank You!

[mvelikov]

Hello, I saw the post is about Innosilicon A4+, buy I can't find such one for Innosilicon D9.

I have 2 Innosilicon D9 opened to Internet  (Yes, I know that this is a bad idea) since yesterday when 1 of the miner starts mining for someone else. The password was changed and I cannot login to the miner. Now I am trying to hard reset (reset the firmware) to its defaults. I am trying to to the tutorial from this post, but it is not working for D9. I can connect via PuTTy wit miner IP + port 22 and SSH, but the username and/or password is incorrect. Any suggestions?

[mvelikov]

Hello, I saw the post is about Innosilicon A4+, buy I can't find such one for Innosilicon D9.

I have 2 Innosilicon D9 opened to Internet  (Yes, I know that this is a bad idea) since yesterday when 1 of the miner starts mining for someone else. The password was changed and I cannot login to the miner. Now I am trying to hard reset (reset the firmware) to its defaults. I am trying to to the tutorial from this post, but it is not working for D9. I can connect via PuTTy wit miner IP + port 22 and SSH, but the username and/or password is incorrect. Any suggestions?

I found it: blacksheepwall <- This is the password for root for D9 and Z9

[KhobHosting]

i cant seem to connect o the Inno a9 Zmater on port 8100?
anyone know what i doing wrong
telnet ip port

[FloDu66]

Hello, I sell 4 miners A4 + and also 2 miners A8 +
make Offer
thank you

Hello,

Does all hashboard all devices work well?

[ketyMINING]

So I just inherited an Innosilicon  A4+ and updated the firmware after resetting to factory default and cannot get in... What is the right password

[hogito]

One more trouble: I can not access miner configuration using password 12345678. I'm getting reply that password is wrong. Is it possible to reset this password?

Thank you


UPD: Solved:
telnet to the miner and opened file:
cd /home/www/conf
vi password

password is written there

I tried this and no value returns.  Worked on one miner but not on another.  Any thoughts?

[thomasmorrison]

When i input " :wq " for save the file inno_config.py i get error "READ ONLY FILE" and i can't save the changes. Any solution?

The sudo command allows you to override the permissions of the file 550 (rxrx-). 
":wq" won't override but ":w!" will.

Note that the purpose of the "!" is to 'force' your command "w".
":wq" doesn't include the 'force' modifier.

[T3ch92]

Hi,

Got some A4+ and I want to change freq.

Anyone know if this work?
Telnet into miner.
cd innocfg/www/conf
vi miner.conf

And change freq there from 1044 to 522?

Would be fun to know if underclocking work on A4+, with original firmware, or I need to make custom.

If anyone know a simple way to underclock, please reply 

Regards

[T3ch92]

It worked to telnet and vi innocfg/www/conf/miner.conf
And change freq from 1044 to 600, so now I can try diff settings, and see if I can get som quiet home solo miners
When freq was 600, fan was in auto and did 30%. Will try to get it down to 10%

Dont know if anyone else here want quiet solo miners, but this is a cheaper way to do it then buying a Apollo miner for $350 or something like that.
Where I am, A4+ goes for $50.

[claypaky]

a4+_20190312_032956.swu  6750DDF4B654344926B1C66AF09D666D

what is this file ?

[mishut]

It worked to telnet and vi innocfg/www/conf/miner.conf
And change freq from 1044 to 600, so now I can try diff settings, and see if I can get som quiet home solo miners
When freq was 600, fan was in auto and did 30%. Will try to get it down to 10%

Dont know if anyone else here want quiet solo miners, but this is a cheaper way to do it then buying a Apollo miner for $350 or something like that.
Where I am, A4+ goes for $50.

Hi!
What firmware do you have? What is your hashrate on that 600MHz? And what about power usage?
Im very interested! 
I have two L3+@BlissZ on 312MHz@405MHs@550W and now want to make that same thing with A4+. Im curious about about W/MHs

[T3ch92]

It worked to telnet and vi innocfg/www/conf/miner.conf
And change freq from 1044 to 600, so now I can try diff settings, and see if I can get som quiet home solo miners
When freq was 600, fan was in auto and did 30%. Will try to get it down to 10%

Dont know if anyone else here want quiet solo miners, but this is a cheaper way to do it then buying a Apollo miner for $350 or something like that.
Where I am, A4+ goes for $50.

Hi!
What firmware do you have? What is your hashrate on that 600MHz? And what about power usage?
Im very interested! 
I have two L3+@BlissZ on 312MHz@405MHs@550W and now want to make that same thing with A4+. Im curious about about W/MHs

Hi,
On the A4+ I use factory firmware, that I tune using telnet.

You could tune L3+ also, or use custom firmware.
DM if you want more info :-)

[Ilovegold]

Has anyone posted how to manually set the fan speed? I am new to trying to telnet mods. I can log in and look around but haven't found any global fanspeed variables.

My miner is doing a weird paradoxical thing since I had to replace a fan where on the miner console page 70% fan speed behaves actually like 30% and vice versa. So my miner thinks it is increasing speed as it heats up but actually reduces fan speed, ie barely moving air at 100% but a jet engine at 30%.

EDIT:

I figured it out. I broke a fan pedal but I now have full fan control.

New problem one of my hashing boards won't recognize. I have no clue why, I fully inspected it and everything is totally intact. But it won't establish it's type or mine.

the "type" says "TYPE_ERR" and the log says "unknown miner !!!" Anyway, I am sure all the chips are fine, but have no clue how to fix it or check it.
Any ideas?

[T3ch92]

Does anyone have any idea what this problem might be?  After power on 3 of the hashboards we´re going down in hashing power now they jump back and forth from dead to alive status with 0 H/s hash

Code:

Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain0: ERROR - failed to recv spi data
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chip clear work false
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain2: ERROR - failed to recv spi data
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chip clear work false
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain3: ERROR - failed to recv spi data
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chip clear work false
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain3: ERROR - failed to recv spi data
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain3: RESET failed
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain3: power down
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain2: ERROR - failed to recv spi data
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain2: RESET failed
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain2: power down
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain0: ERROR - failed to recv spi data
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain0: RESET failed
Jul 02 23:03:54 InnoMiner mcompat_lib[1329]: chain0: power down
Jul 02 23:03:55 InnoMiner dm-monitor[1316]: ## Error: "watchdog" not defined
Jul 02 23:03:56 InnoMiner nginx[1340]: 127.0.0.1 - - [02/Jul/2021:23:03:56 +0000] "POST /api/auth HTTP/1.1" 200 208 "-" "curl/7.59.0"
Jul 02 23:03:56 InnoMiner mcompat_lib[1329]: chain3: set vid 0
Jul 02 23:03:56 InnoMiner mcompat_lib[1329]: chain3: sleep(6)
Jul 02 23:03:56 InnoMiner mcompat_lib[1329]: chain2: set vid 0
Jul 02 23:03:56 InnoMiner mcompat_lib[1329]: chain2: sleep(6)
Jul 02 23:03:56 InnoMiner mcompat_lib[1329]: chain0: set vid 0
Jul 02 23:03:56 InnoMiner mcompat_lib[1329]: chain0: sleep(6)
Jul 02 23:03:57 InnoMiner mcompat_lib[1329]: API: access denied to '192.168.1.15' for 'privileged' command
Jul 02 23:03:57 InnoMiner mcompat_lib[1329]: BA1 1: invalid nonce - HW error
Jul 02 23:03:57 InnoMiner mcompat_lib[1329]: 1: chip 68: invalid nonce 0xf8627900 !
Jul 02 23:03:58 InnoMiner mcompat_lib[1329]: BA1 1: invalid nonce - HW error
Jul 02 23:03:58 InnoMiner mcompat_lib[1329]: 1: chip 48: invalid nonce 0xad6f8700 !
Jul 02 23:04:01 InnoMiner mcompat_lib[1329]: BA1 1: invalid nonce - HW error
Jul 02 23:04:01 InnoMiner mcompat_lib[1329]: 1: chip 25: invalid nonce 0x8e9ff200 !
Jul 02 23:04:01 InnoMiner mcompat_lib[1329]: BA1 1: invalid nonce - HW error
Jul 02 23:04:01 InnoMiner mcompat_lib[1329]: 1: chip 46: invalid nonce 0xfebaf400 !
Jul 02 23:04:01 InnoMiner mcompat_lib[1329]: BA1 0: Idle for more than 60 seconds, declaring SICK!
Jul 02 23:04:01 InnoMiner mcompat_lib[1329]: BA1 0: Attempting to restart
Jul 02 23:04:01 InnoMiner mcompat_lib[1329]: BA1 1: invalid nonce - HW error
Jul 02 23:04:01 InnoMiner mcompat_lib[1329]: 1: chip 67: invalid nonce 0x8a610601 !
Jul 02 23:04:02 InnoMiner mcompat_lib[1329]: BA1 1: invalid nonce - HW error
Jul 02 23:04:02 InnoMiner mcompat_lib[1329]: 1: chip 47: invalid nonce 0x16381e01 !
Jul 02 23:04:02 InnoMiner mcompat_lib[1329]: chain3: encore fourth mode
Jul 02 23:04:02 InnoMiner mcompat_lib[1329]: chain2: encore fourth mode
Jul 02 23:04:02 InnoMiner mcompat_lib[1329]: chain0: encore fourth mode
Jul 02 23:04:02 InnoMiner mcompat_lib[1329]: API: access denied to '192.168.1.15' for 'privileged' command
Jul 02 23:04:03 InnoMiner mcompat_lib[1329]: recieve notify,we must flush work
Jul 02 23:04:03 InnoMiner mcompat_lib[1329]: New block: 39377ed685d70d9159c5262cc93cfc2ccd34a1313a1da9d2174680fe919c7d74... diff 6.84M

Fan speed can be adjusted in telnet with vi.
Did you figure it out?

When I had same problem with hashboard, I just needed to flash new firmware.

Firmware "update_180622.bin" worked for me :-)
But you could also try "update_180129.bin"