Antminer S9 - No data in Miner Status page

[tim-bc]

Cool, this is a relatively common problem with the newer firmwares. At any rate, flashing the april 2017 firmware should fix the issue (you can thank fanatic26 for the tip):

https://www.dropbox.com/s/v5r5n46eajetme4/Antminer-S9-all-201704270135-autofreq-user-Update2UBI-NF.tar.gz?dl=0
https://www.mediafire.com/file/986jp6m02svz7ya/Antminer-S9-all-201704270135-autofreq-user-Update2UBI-NF.tar.gz
https://1drv.ms/u/s!AtkfLUFCwpoBaWvM7d0-19mvBYo

You should confirm that the sha1sum is 0515029015ad8dcedb185367fc5f829851dc65ed before flashing

[1714170378]

1714170378

[1714170378]

1714170378

[HELIUM_COIN]

Ok, Great thanks waiting to hear from seller before I do the update.

Greatly appreciated.

[HELIUM_COIN]

Well no luck, shaw hash was correct, but now it's a different error as follows:

Code:

After restore: chain[5] PIC fw version=0x00
post search failed code: U6:1
post: http://192.168.60.104/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1
ERROR: Failed to fetch url (http://192.168.60.104/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1) - curl said: Timeout was reached 
post: http://10.70.22.1/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1
ERROR: Failed to fetch url (http://10.70.22.1/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1) - curl said: Timeout was reached 
post: http://10.72.3.11/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1
ERROR: Failed to fetch url (http://10.72.3.11/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1) - curl said: Timeout was reached

Also, tried the firmware on the bitmain site and am back to the original error.
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
After restore: chain[5] PIC fw version=0x00
post search failed code: U6:1
post: http://192.168.60.104/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1
ERROR: Failed to fetch url (http://192.168.60.104/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1) - curl said: Timeout was reached 
post: http://10.70.22.1/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1
ERROR: Failed to fetch url (http://10.70.22.1/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1) - curl said: Timeout was reached 
post: http://10.72.3.11/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1
ERROR: Failed to fetch url (http://10.72.3.11/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1) - curl said: Timeout was reached

I guess there is an unfix-able hardware issue?  Hmmm..

Thanks for any help, greatly appreciated...

[HELIUM_COIN]

Here's the entire log:

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000305] ps7-ttc #0 at f0006000, irq=43
[    0.000617] Console: colour dummy device 80x30
[    0.000653] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.090252] pid_max: default: 32768 minimum: 301
[    0.090476] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.090498] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.092630] CPU: Testing write buffer coherency: ok
[    0.092979] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.093039] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[    0.093265] L310 cache controller enabled
[    0.093284] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.171033] CPU1: Booted secondary processor
[    0.260226] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.260356] Brought up 2 CPUs
[    0.260375] SMP: Total of 2 processors activated.
[    0.260383] CPU: All CPU(s) started in SVC mode.
[    0.261034] devtmpfs: initialized
[    0.263434] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.264641] regulator-dummy: no parameters
[    0.272334] NET: Registered protocol family 16
[    0.274522] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.276810] cpuidle: using governor ladder
[    0.276824] cpuidle: using governor menu
[    0.284280] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.285795] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.285809] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.285923] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.307388] bio: create slab <bio-0> at 0
[    0.308789] vgaarb: loaded
[    0.309486] SCSI subsystem initialized
[    0.310525] usbcore: registered new interface driver usbfs
[    0.310706] usbcore: registered new interface driver hub
[    0.310927] usbcore: registered new device driver usb
[    0.311584] media: Linux media interface: v0.10
[    0.311741] Linux video capture interface: v2.00
[    0.311979] pps_core: LinuxPPS API ver. 1 registered
[    0.311991] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.312121] PTP clock support registered
[    0.312473] EDAC MC: Ver: 3.0.0
[    0.313520] Advanced Linux Sound Architecture Driver Initialized.
[    0.316374] DMA-API: preallocated 4096 debug entries
[    0.316388] DMA-API: debugging enabled by kernel config
[    0.316465] Switched to clocksource arm_global_timer
[    0.337512] NET: Registered protocol family 2
[    0.338175] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.338269] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.338428] TCP: Hash tables configured (established 8192 bind 8192)
[    0.338491] TCP: reno registered
[    0.338510] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.338563] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.338818] NET: Registered protocol family 1
[    0.339176] RPC: Registered named UNIX socket transport module.
[    0.339188] RPC: Registered udp transport module.
[    0.339197] RPC: Registered tcp transport module.
[    0.339206] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.339219] PCI: CLS 0 bytes, default 64
[    0.339664] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.341680] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.343077] bounce pool size: 64 pages
[    0.343968] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.344169] msgmni has been set to 1486
[    0.344950] io scheduler noop registered
[    0.344963] io scheduler deadline registered
[    0.345003] io scheduler cfq registered (default)
[    0.356946] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.356967] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.480304] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.053265] console [ttyPS0] enabled
[    1.057561] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.065182] [drm] Initialized drm 1.1.0 20060810
[    1.082124] brd: module loaded
[    1.091525] loop: module loaded
[    1.100967] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.106793] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.114522] libphy: XEMACPS mii bus: probed
[    1.119073] ------------- phy_id = 0x3625e62
[    1.123805] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.132569] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.139233] ehci-pci: EHCI PCI platform driver
[    1.146443] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.153264] usbcore: registered new interface driver usb-storage
[    1.160129] mousedev: PS/2 mouse device common for all mice
[    1.166229] i2c /dev entries driver
[    1.173163] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.178700] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.184582] Xilinx Zynq CpuIdle Driver started
[    1.189487] sdhci: Secure Digital Host Controller Interface driver
[    1.195580] sdhci: Copyright(c) Pierre Ossman
[    1.199944] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.206802] mmc0: no vqmmc regulator found
[    1.210818] mmc0: no vmmc regulator found
[    1.246483] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.255171] usbcore: registered new interface driver usbhid
[    1.260675] usbhid: USB HID core driver
[    1.265391] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.271694] nand: Micron MT29F2G08ABAEAWP
[    1.275657] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.281604] Bad block table found at page 131008, version 0x01
[    1.287822] Bad block table found at page 130944, version 0x01
[    1.293875] 3 ofpart partitions found on MTD device pl353-nand
[    1.299655] Creating 3 MTD partitions on "pl353-nand":
[    1.304748] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.312825] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.320143] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.329074] TCP: cubic registered
[    1.332312] NET: Registered protocol family 17
[    1.337038] Registering SWP/SWPB emulation handler
[    1.342907] regulator-dummy: disabling
[    1.347251] UBI: attaching mtd1 to ubi0
[    1.871821] UBI: scanning is finished
[    1.883430] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.890514] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.897276] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.903941] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.910818] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.916799] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.923906] UBI: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 1283732989
[    1.932949] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.942166] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.942172] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.946074] ALSA device list:
[    1.946078]   No soundcards found.
[    1.962512] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    2.030153] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.036082] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.045223] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.055184] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.060171] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C72F8006-6DFF-46BA-BBE9-380960A89F92, small LPT model
[    2.071687] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.078652] devtmpfs: mounted
[    2.081757] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.924610] random: dd urandom read with 0 bits of entropy available
[    3.316489] 
[    3.316489] bcm54xx_config_init
[    3.926498] 
[    3.926498] bcm54xx_config_init
[    7.927343] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.933437] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   22.582436] In axi fpga driver!
[   22.585509] request_mem_region OK!
[   22.588942] AXI fpga dev virtual address is 0xf01fe000
[   22.594007] *base_vir_addr = 0x8c510
[   22.609615] In fpga mem driver!
[   22.612687] request_mem_region OK!
[   22.616284] fpga mem virtual address is 0xf3000000
[   23.405857] 
[   23.405857] bcm54xx_config_init
[   24.035829] 
[   24.035829] bcm54xx_config_init
[   28.036266] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   28.042283] xemacps e000b000.ps7-ethernet: link up (100/FULL)
This is XILINX board. Totalram:       1039794176
Detect 1GB control board of XILINX
DETECT HW version=0008c510
miner ID : 80744c012c00885c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
Find /tmp/searcherror: U6:1  The last log is below:
This is XILINX board. Totalram:       1039794176
Detect 1GB control board of XILINX
DETECT HW version=0008c510
miner ID : 80744c012c00885c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x00
chain[5] PIC need restore ...
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
Error of set PIC FLASH addr: addr_H=3(0) addr_L=0(0) on Chain[5]
After restore: chain[5] PIC fw version=0x00
post search failed code: U6:1
post: http://192.168.60.104/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1
ERROR: Failed to fetch url (http://192.168.60.104/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1) - curl said: Timeout was reached 
post: http://10.70.22.1/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1
ERROR: Failed to fetch url (http://10.70.22.1/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1) - curl said: Timeout was reached 
post: http://10.72.3.11/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1
ERROR: Failed to fetch url (http://10.72.3.11/mms/postfailedcode.do?minertype=S9&minerID=80744c012c00885c&failedCode=U6:1) - curl said: Timeout was reached

[ddrewtx]

Greetings all. New forum member, recently purchased 4 Antminer V9's with APW3++ power supplies. I have them in a colo data center running 220v and ALL have a similar problem. The V9's are running Linux 4.6.0-xilinx-gff8137b-dirty #22 SMP PREEMPT Fri Dec 22 12:25:44 CST 2017 and CGMiner 4.9.0. I've heard the V9 is a clone of the S9, so I'm hoping this thread can help me resolve the problem.

I have an issue where the miners become disconnected from Awesome Miner V5.3.1, and when I go into the web interface, the System/Overview has no data, but has the data field names, and the Miner Status is the same, no data but has data field names. I can ping them and they respond, but won't connect. I have been rebooting them to resolve this, and they connect within a few minutes, and remain hashing, for various timeframes. Sometimes they disconnect in a few hours, but in most instances they will disconnect right at 8:45 minutes of uptime.

I can see the kernel log, when it is in this state, and most of the time it leaves this as the last entry 'Jul 14 16:20:59 (none) local0.err cgminer[955]: cgminer time error total_secs = 1531585179.097935 last_total_secs = 889.864640'. I've researched and can't find alot of info on this, whether it is an error or not. It is the only entry in the Kernel Log with the correct date/time. This just happened again while researching and all 4 miners went 'disconnected' at the same time. This Kernel Log error did not appear in this last entry.  I had the colo data center check the network and they say there were no problems at the time these problems happened that could have caused these disconnects.

I would really appreciate any insight into this problem, and/or suggestions to resolve it. 

[NotFuzzyWarm]

You said

This just happened again while researching and all 4 miners went 'disconnected' at the same time.

As in within a few seconds of each other? If that is the case then highly unlikely the problem is with the miners as they are independent devices. That of course leaves a network issue, pool issue, or power feeding that bank of miners issue. What pool ya pointed at?

[ddrewtx]

This is a private blockchain project and we are connecting to a private pool. I was thinking there is something in the pool causing it, but that's hard to confirm. This set of 4 miners was just replaced due to a similar problem, but they would not reconnect. I think the original miners were hacked since the passwords were changed, and the factory reset was disabled. Again that is hard to substantiate. Any other ideas? Thanks in advance for all your help.