|
asjfdlksfd
|
 |
January 14, 2014, 07:20:50 AM |
|
Probably not, though we've talked about it. I have given Lucko a version that slowly raises the maximum permitted voltage over the span on 5 minutes, which could help. It doesn't work on mine, though Lucko did indicate mine was the worst of the batch.
Ok, is it possible to have an invitation to the test? I've 8 of 10 boards which will start only with the hairdryer method. |
|
|
|
|
bx8389
Member
 Offline
Activity: 80
Merit: 10
|
|
January 14, 2014, 09:35:16 AM
Last edit: January 14, 2014, 10:27:51 AM by bx8389 |
|
the 'hair dryer' solution is not acceptable. I can confirm that. The method is acceptable so I will not lost all my money because there mining now, more or less. I think all people agree that is not an ideal solution, is a way to minimize losses. I understand also this is tricky problem so find root causes can take some time. After all, hundred other MrTeal ‘s boards work and seems only this batch have trouble. I believe on MrTeal and Lucko professionalism and expect in next few days a clear explanation about board problem's root causes and viable solution if possible. But if not able to find the problem cause´s I expect ,at least, Mr Teal give board’s enough information for all affected people search a solution by his own. Regards |
|
|
|
|
|
Mudbankkeith
|
|
January 14, 2014, 10:35:40 AM |
|
Probably not, though we've talked about it. I have given Lucko a version that slowly raises the maximum permitted voltage over the span on 5 minutes, which could help. It doesn't work on mine, though Lucko did indicate mine was the worst of the batch.
Ok, is it possible to have an invitation to the test? I've 8 of 10 boards which will start only with the hairdryer method. It has to be a problem with the switching logic, but is it hardware, software, or both. Some open source input may find a solution, (many minds together, become creative) but a moderator would be desirable. |
BTc donations welcome:- 13c2KuzWCaWFTXF171Zn1HrKhMYARPKv97
|
|
|
|
Lucko (OP)
|
|
January 15, 2014, 10:07:05 AM |
|
OK this firmware fix looks promising... out of 10 boards with it non crashes on a first start(for now it only handles first start) and then normal operations... It still needs work...
|
|
|
|
|
|
|
|
Lucko (OP)
|
|
January 19, 2014, 01:35:26 PM |
|
I will probably start to ship tomorrow... I have finish about 20 boards now... This time I'm testing them longer and looking to put best firmware on... So it is a bit slower then the last time. |
|
|
|
|
|
Mudbankkeith
|
|
January 19, 2014, 01:39:19 PM |
|
I will probably start to ship tomorrow... I have finish about 20 boards now... This time I'm testing them longer and looking to put best firmware on... So it is a bit slower then the last time.
Hi Lucko Will the software fixes be posted on dropbox (the same way MrTeal posted a few weeks ago?) |
BTc donations welcome:- 13c2KuzWCaWFTXF171Zn1HrKhMYARPKv97
|
|
|
|
Min€r
|
|
January 19, 2014, 08:00:27 PM |
|
I will probably start to ship tomorrow... I have finish about 20 boards now... This time I'm testing them longer and looking to put best firmware on... So it is a bit slower then the last time. Really cool - can`t wait to get them  |
|
|
|
ronin4bits
Newbie
Offline
Activity: 59
Merit: 0
|
|
January 20, 2014, 10:19:24 PM |
|
I will probably start to ship tomorrow... I have finish about 20 boards now... This time I'm testing them longer and looking to put best firmware on... So it is a bit slower then the last time.
Can't wait to get mine, Lucko. Thanks! |
|
|
|
|
|
asjfdlksfd
|
|
January 21, 2014, 03:08:53 AM |
|
Hi all,
I would like to inform that one of the test fw prevents us from using a hairdryer to warmup the Chilly at startup. I used the one which ramps up with beginning of hashing.
So good work to Mr. Teal to help me and my girl friend who must not further search the hair dryer.
But the restart issue is still available if mining is interrupted. This looks like comes from a cool down phase in seconds if mining is interrupted. After hashing restarts the chillies resets again which could come from the
high voltages but the power chips has been cooled down.
I think a possible solution could be a temperature check if mining is throttled or interrupted or phase2 has been shut down. So the voltage ramp up for preheating should restart to prevent us from the same behavior interrupt/reset.
Cheers...
|
|
|
|
|
|
hephaist0s
|
|
January 21, 2014, 02:17:05 PM |
|
Lucko, just checking to make sure mine are being sent.
|
Tips graciously accepted on my behalf by Mr. Pig. | object2212.com | BTC:1H78y8FVeQrWY6KnxA6WLFQGUoajCuiMAu | ETH:0x3c1bC39EC7F3f6b26ACb6eeeEFe7dE2f486a72E9 |
|
|
|
Lucko (OP)
|
|
January 21, 2014, 10:03:33 PM |
|
I'm just getting ready for tomorrow to start sending "batch2" of this make... You are included... You will receive mail soon. It is a bit slower since I'm making sure that all phase are working OK and that boards work well under bigger range of conditions. If they are send tomorrow(please answer mail ASAP) US will receive them on 24th.
|
|
|
|
|
dwdoc
Legendary
Offline
Activity: 966
Merit: 1000
- - -Caveat Aleo- - -
|
|
January 22, 2014, 12:09:04 AM |
|
On the 4 month anniversary of delivery of my BFL chips Lucko has got my chips hashing! He is still tweaking them but hashing at 250 GH/s right now-Go Lucko!!
|
|
|
|
|
|
|
|
Lucko (OP)
|
|
January 22, 2014, 06:44:29 PM |
|
All who replayed should see delivery estimate not in tracking you received. No idea why some of you in US will received it on 24th and some on 27th. Service is the same. Could be location related... For the rest please do so ASAP...
|
|
|
|
|
ronin4bits
Newbie
Offline
Activity: 59
Merit: 0
|
|
January 22, 2014, 06:46:07 PM |
|
Looks like I'm on the 24th!  Thank you, Lucko! |
|
|
|
|
Bogart
Legendary
Offline
Activity: 966
Merit: 1000
|
|
January 22, 2014, 07:13:23 PM |
|
I'm just getting ready for tomorrow to start sending "batch2" of this make... You are included... You will receive mail soon. It is a bit slower since I'm making sure that all phase are working OK and that boards work well under bigger range of conditions. If they are send tomorrow(please answer mail ASAP) US will receive them on 24th.
No email received yet... |
"All safe deposit boxes in banks or financial institutions have been sealed... and may only be opened in the presence of an agent of the I.R.S." - President F.D. Roosevelt, 1933
|
|
|
|
Lucko (OP)
|
|
January 22, 2014, 07:39:21 PM |
|
I'm just getting ready for tomorrow to start sending "batch2" of this make... You are included... You will receive mail soon. It is a bit slower since I'm making sure that all phase are working OK and that boards work well under bigger range of conditions. If they are send tomorrow(please answer mail ASAP) US will receive them on 24th.
No email received yet... I have about 30 boards to go to finish this make and for batch3 You are there... And so are the rest who didn't received mail... |
|
|
|
|
cannachris
Sr. Member
Offline
Activity: 406
Merit: 250
cats love crypto | 911 truth @checktheevidence.com
|
|
January 24, 2014, 01:45:07 PM |
|
I ordered quite some time ago but heard nothing back - will I be in the next batch? Otherwise are you still selling these?
|
|
|
|
|
Lucko (OP)
|
|
January 24, 2014, 02:06:14 PM |
|
I ordered quite some time ago but heard nothing back - will I be in the next batch? Otherwise are you still selling these?
I did send you a email. When you didn't replay I was guessing you are not interested... |
|
|
|
|
|
