rudyo
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
December 26, 2013, 06:01:53 AM |
|
What is the consensus on card orientation - horizontal vs vertical?
I haven't been able to find a good discussion that comes to any conclusion. I get that most GPU fans suck air in and push it across the fins over processor and out the back through the mount plate evtns (where the DVI plug is) but this setup is for a sealed case. In this traditional setup, having the cards vertical an allowing the heat to rise up and out may be a benefit.
It seems we upset the normal flow when we put an additional fan blowing between the cards, so does this negate the card placement? has anyone has better results horizontal or vertical?
|
|
|
|
hakeriukasx
Newbie
Offline
Activity: 58
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 11, 2014, 11:54:07 AM |
|
two(2) 8 foot lengths of 3/4" square aluminum tubing for connectors, I dont understand inch and feet and etc ,8 foot= 2.5m?
|
|
|
|
dannymack
Newbie
Offline
Activity: 52
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 14, 2014, 10:19:49 PM |
|
Thanks for the directions. So, I used your sizes (a bit modified) and I even used Brunner ...the supplier you linked to. What I did differently was give them the sizes I needed and they cut it for me...only .69 cents a cut. I also decided to use a regular case for the bottom..was just easier to fit everything in and comes with power buttons and all..only cost me $39 (X-Dreamer3) ...As such, I had to make it higher...but those numbers above allowed me to figure out the height for the cards. A problem with my way was...it's now two separate pieces and difficult (but not impossible) to move. Here's what it looks like: https://imgur.com/a/uKm87
|
|
|
|
G K G
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 15, 2014, 03:06:14 AM |
|
![Cool](https://bitcointalk.org/Smileys/default/cool.gif) I should have got the grey connectors. ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fimg.photobucket.com%2Falbums%2Fv239%2Fzif33%2F20130523_093918.jpg&t=665&c=lCKu7lnX0vyNtQ) Nice setup. What do you use to boot the OS? lan boot or you use a HDD?
|
|
|
|
Eternity
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 15, 2014, 09:59:03 AM |
|
Awesome lots of info am too lazy to try that on my own ![Cheesy](https://bitcointalk.org/Smileys/default/cheesy.gif)
|
|
|
|
predatorkill
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 18, 2014, 01:37:36 PM |
|
Here's my rig, 1x6970, 2x6950 and 1x7970 hashing at 2.1MH/s. I ve made it from iron parts and not alluminium and i use 2 psu's, one bronze for mobo and 2x6950 and the other is silver for 7970 and 6970. The dimensions are 25cm longer so it can fit the 2 psu. Thanks for this wonderful guide, temperatures dropped 5 degrees celcious after 'moving' from a plastic crate to this. ![Cheesy](https://bitcointalk.org/Smileys/default/cheesy.gif) check images below: ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fi35.photobucket.com%2Falbums%2Fd157%2Fpredatorkill1%2FIMG_1588_zps0d31257e.jpg&t=665&c=NTJlYZWhdXvtYQ) .. ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fi35.photobucket.com%2Falbums%2Fd157%2Fpredatorkill1%2FIMG_1590_zps82069b60.jpg&t=665&c=n4eva4TZHdp9Cg) .. ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fi35.photobucket.com%2Falbums%2Fd157%2Fpredatorkill1%2FIMG_1591_zps8386bc81.jpg&t=665&c=6D8S7dQjKuCvxQ) ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fi35.photobucket.com%2Falbums%2Fd157%2Fpredatorkill1%2F3k11_zpsc2e44141.png&t=665&c=ziI07TmpU6NVcw) .. ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fi35.photobucket.com%2Falbums%2Fd157%2Fpredatorkill1%2FIMG_1593_zps91a767bc.jpg&t=665&c=TvQ0g7S1LTcyIg) in the last image you can see the green and black wire jumpers in order to connect the 2 psu together and power on at the same time with button press.
|
|
|
|
BillGeo
Newbie
Offline
Activity: 39
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 20, 2014, 08:50:17 AM |
|
Here's my rig, 1x6970, 2x6950 and 1x7970 hashing at 2.1MH/s. I ve made it from iron parts and not alluminium and i use 2 psu's, one bronze for mobo and 2x6950 and the other is silver for 7970 and 6970. The dimensions are 25cm longer so it can fit the 2 psu.
Very nice heavy and solid rig build patrida!!! ![Cool](https://bitcointalk.org/Smileys/default/cool.gif) I came here from insomnia.gr to see the pics!!! APSOGOS! ![Roll Eyes](https://bitcointalk.org/Smileys/default/rolleyes.gif)
|
|
|
|
IchibahnSLC
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 23, 2014, 02:17:02 AM |
|
Anyone know if these connectors are available at home depot, lowes or ace hardware?
|
|
|
|
Thyatis
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 23, 2014, 02:23:37 AM |
|
i will pay someine to build me multiple of these pm me details
|
|
|
|
Thyatis
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 23, 2014, 02:26:23 AM |
|
i will pay someine to build me multiple of these pm me details
just the rig no motherboard etc etc i have all that jut not wenought time to source parts and build it
|
|
|
|
prhvideos
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 23, 2014, 03:19:39 AM |
|
This is an impressive rig, I am new to crypto currency and have been looking at a lot of builds and guides. Thanks for posting all this man, great for opening up the mind and some personal dream building ;P
|
|
|
|
grobbes
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 60
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 23, 2014, 04:22:56 AM Last edit: January 23, 2014, 04:33:11 AM by grobbes |
|
Finally built my first. Used a hacksaw and edges came out a little uneven but it still gets the job done ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) Thanks OP! ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fi39.tinypic.com%2Fznkdqb.jpg&t=665&c=Ppj5qh9z1yGQ5A)
|
|
|
|
IchibahnSLC
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 23, 2014, 07:05:57 AM |
|
Has no one bought any supplies locally for this? In the US that is.
|
|
|
|
|
IchibahnSLC
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 23, 2014, 07:19:33 AM |
|
Yeah the connectors are my issue as well.
|
|
|
|
grobbes
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 60
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 23, 2014, 07:22:29 AM |
|
Yeah the connectors are my issue as well. Brunner ships super fast even though the shipping/handling is a bit high (it was top notch though). I believe the cheapest shipping got everything to me in 2 days and the order processed the same day as ordering. In the future though, I'd just grab the 4 ft tubings since the UPS guy had some fun getting the 8 foot ones into my apartment ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
|
|
|
cad_cdn
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 25, 2014, 06:54:44 PM |
|
thx for the guide!
|
|
|
|
SneakyNinjA
Newbie
Offline
Activity: 21
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 26, 2014, 07:32:13 PM |
|
I made this out of wood for ~$5.00, so if you live near a lowes or home depot, you can just buy screws and 1x4's and you're set.
Does anyone have a PDF print out or link to a website that has the exact placement of the screwholes of the ATX mobo's? I had to take my mobo and use a sharpie before putting in the holes.
|
|
|
|
|
SneakyNinjA
Newbie
Offline
Activity: 21
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 26, 2014, 09:26:00 PM |
|
Not sure if you noticed GKG, but no one has received their openrigs order. Not saying he's scamming, just that shipments from South Arica not only cost a lot, but take 2+ months... (longer than shipping EMS from China)
|
|
|
|
|