[CLOSED] batch #32 0.65 btc per Blade, 49-port HUBS .30 or less

[philipma1957]

ONE place to buy idiot proof dc plugs is good old mcmelectronics.com  unlike the crap pus's early in this thread they have a great dc power cord.  it has a blue led and a red led.  if wired wrong for hubs the led is red .  red is dead you will burn the hub up.   if the led is blue it is wired correctly.  give me a few minutes. i will post some nice 7 port hubs


http://www.mcmelectronics.com/product/82-12675   link for the wire same code afc909 for discount.

now that sticks are going going gone  I wonder if AM will  sell a better stick. It would be nice if they cut a deal with bitfury and made the 2.5gh sticks just as fast as they made these sticks..

[philipma1957]

okay my photos of 4x    7 port hubs hooked up.  


using the magic dc power wires blue led is cool red is dead.



a low cost 3 prong switch from lowes. 




the cut 3 prong power cord from an old power strip  one in the switch from lowes and to the psu

[philipma1957]

a close up of the psu   note the red electrical tape over the 3 ac power wires is for safety as it is live power .





last the psu is good for  26amp 130 watts at 5 volts    my 4 hubs are 28 sticks and pull 100 watts at the wall.  so this is a great setup for 28 sticks.





this would be a perfect  setup for the bitfury sticks

 hint hint

[helipotte]

Just updated prices on blades.

Also, there are no more USBs available from the manufacturer.  Whatever remains on hand at resellers is it folks.  Once they're gone, they won't be restocked or made again.

I still have plenty on hand with good color selection and offcourse 50 units include the 49 port USB hub.

Are the blades still in production? Or are they stopping production on all BE100 based miners.  Maybe gearing up for V2?

[philipma1957]

Just updated prices on blades.

Also, there are no more USBs available from the manufacturer.  Whatever remains on hand at resellers is it folks.  Once they're gone, they won't be restocked or made again.

I still have plenty on hand with good color selection and offcourse 50 units include the 49 port USB hub.

Are the blades still in production? Or are they stopping production on all BE100 based miners.  Maybe gearing up for V2?

if they made a new stick they need  a different chip.    even 1gh-1.5gh stick with power at 2.5 to 3 watts would work. 

[Paddy]

1.75 sent for 50 USB's and Hub

Transaction Id:  ee678f305119148eaa4bfb33d943cc333208b13435233b5d081cf5aed7cd9fa4

Payment address:  1PJ1A1ukF1CqDsmNd7QVdmCyt4bsQFo9pA

Label sent in email

Thanks

 
 
 

[helipotte]

Just updated prices on blades.

Also, there are no more USBs available from the manufacturer.  Whatever remains on hand at resellers is it folks.  Once they're gone, they won't be restocked or made again.

I still have plenty on hand with good color selection and offcourse 50 units include the 49 port USB hub.

Are the blades still in production? Or are they stopping production on all BE100 based miners.  Maybe gearing up for V2?

if they made a new stick they need  a different chip.    even 1gh-1.5gh stick with power at 2.5 to 3 watts would work. 

V2 = smaller process node, same design.  Maybe then, higher clocks and/or x2 chips per stick would achieve 1-1.5Gh.

[CanaryInTheMine]

So does anyone have instructions on how to wire an ATX connector to the above PSU in pics?

[helipotte]

So does anyone have instructions on how to wire an ATX connector to the above PSU in pics?

I have not seen the PSU but I suspect you could just connect all of the red wires to V+, all of the black wires to V-.  The rest of the wires could be removed from the 24 pin connector or ignored.  I think they all float on the hub side except for the green wire that turns on the ATX power supply. 
This wire is even mute with a dedicated 5V PSU.  I think I would rather wire in a switch on the 5V PSU.

[Tong]

So does anyone have instructions on how to wire an ATX connector to the above PSU in pics?

Whithout having one in front of me:  find the pinout assignment for all the +5v connectors on the psu (the wiki page should show you which ones and they're usually the same color) connect those to that psu's + side, then connect all the black ones to the negative side.

I'LL provide a pic once mine gets in and go into more detail, but this should get a few people going in the right direction.

Tong

[aurel57]

You need to balance the load between the three outputs.

[xzempt]

will this psu work for the backplanes?


https://www.amazon.com/dp/B001U0EM1W/ref=as_li_ss_til?tag=pck01-20

[bitterdog]

I need "4 hubs and 200 be. Ill be home from work in a few hours..

[philipma1957]

hold 1 hub and 50 sticks >  I will order in about an hour.

[CanaryInTheMine]

hold 1 hub and 50 sticks >  I will order in about an hour.

you got it!

[CanaryInTheMine]

I need "4 hubs and 200 be. Ill be home from work in a few hours..

I'll hold them for you. thanks!!

[bobsag3]

So does anyone have instructions on how to wire an ATX connector to the above PSU in pics?

https://www.dropbox.com/s/v81yz2trp91025l/Photo%20Nov%2001%2C%204%2023%2023%20PM.jpg

You can use something like that, for both the blades and USB miners

[philipma1957]

hold 1 hub and 50 sticks >  I will order in about an hour.

you got it!

 tx id for 1.75 btc


https://blockchain.info/tx/c0f9b1a421b24cd0aa790845c0341a80eadd9130c6020347e27482f5269b5096


1Fo2K52Rz7LZw9fcF5BDdDBjfNaViQ8J3x


my refund address.   .. did you need a region b box label? and what is the email  address to send the label

[CanaryInTheMine]

hold 1 hub and 50 sticks >  I will order in about an hour.

you got it!

 tx id for 1.75 btc


https://blockchain.info/tx/c0f9b1a421b24cd0aa790845c0341a80eadd9130c6020347e27482f5269b5096


1Fo2K52Rz7LZw9fcF5BDdDBjfNaViQ8J3x


my refund address.   .. did you need a region b box label? and what is the email  address to send the label

region B works or medium, whichever is cheaper for you.  region b box weight should be specified at about 3 pounds

[CanaryInTheMine]

will this psu work for the backplanes?


https://www.amazon.com/dp/B001U0EM1W/ref=as_li_ss_til?tag=pck01-20

visually, looks correct and same as the official part number, just can't tell if that's actually what they will ship you.  but it looks right and the price is VERY good!