Zich (OP)
Legendary
 Offline
Activity: 1190
Merit: 1000
|
 |
December 24, 2014, 07:13:25 AM |
|
A new firmware how did I miss that  No, you didn't That is screenshot from marto, new firmware still not release yet. |
|
|
|
|
|
|
|
|
|
|
|
Each block is stacked on top of the previous one. Adding another block to the top makes all lower blocks more difficult to remove: there is more "weight" above each block. A transaction in a block 6 blocks deep (6 confirmations) will be very difficult to remove.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
|
|
nitrox
Member
Offline
Activity: 136
Merit: 10
tester
|
|
December 24, 2014, 05:29:48 PM |
|
still nothing ....
|
|
|
|
|
marto74
|
|
December 25, 2014, 08:02:48 PM |
|
DICE only release http://technobit.eu/DICE.rar* For DICE ersion DHCP is enebled by default, when flashing fro olde technobit img DO NOT KEEP SETINGS!!!! |
|
|
|
nitrox
Member
Offline
Activity: 136
Merit: 10
tester
|
|
December 26, 2014, 11:06:15 AM |
|
super
|
|
|
|
Zich (OP)
Legendary
Offline
Activity: 1190
Merit: 1000
|
|
December 29, 2014, 06:10:10 AM
Last edit: December 29, 2014, 08:00:15 AM by Zich |
|
DICE only release http://technobit.eu/OK_DICE.rar* For DICE version DHCP is enebled by default, when flashing from older technobit img DO NOT KEEP SETTINGS!!!! *UPDATED + patch 29_12_2014 If you are using tbdice.org solo pool you can find your TP-link IP address by visiting http://tbdice.org/myminers/index.php from a PC in the same LAN where your TP-link with DICE firmware is OP updated. |
|
|
|
|
|
gcube1305
|
|
February 22, 2015, 10:17:53 AM |
|
Thanks for the guide.
Juste a question : i have an old version of openwrt ("OpenWrt Barrier Breaker r40295"), i think it is a 0.3.0. It is working very well, but i'm using a DHCP configuration.
I want to update to 0.4.0, should i change network mode to static configuration ?
When i'm going to the "Network/interfaces" screen, and i select "static", i cannot immediately set the new address, i must click on a "Switch protocol" button. If i click, will it not reset the address immediately, making the tplink not acessible ?
|
|
|
|
|
Zich (OP)
Legendary
Offline
Activity: 1190
Merit: 1000
|
|
February 22, 2015, 10:25:02 AM |
|
Thanks for the guide.
Juste a question : i have an old version of openwrt ("OpenWrt Barrier Breaker r40295"), i think it is a 0.3.0. It is working very well, but i'm using a DHCP configuration.
I want to update to 0.4.0, should i change network mode to static configuration ?
When i'm going to the "Network/interfaces" screen, and i select "static", i cannot immediately set the new address, i must click on a "Switch protocol" button. If i click, will it not reset the address immediately, making the tplink not acessible ?
No, no need to change to static if you want to upgrade to 0.4.0. Just uncheck the save setting option. After upgrade, the default ip is 192.168.0.99. 0.4.0 come with static option, but do not change to DHCP |
|
|
|
|
VoodooServ
Newbie
Offline
Activity: 8
Merit: 0
|
|
February 28, 2015, 12:01:02 PM |
|
Can anyone make this firmware 0.4b-4.0.0 to work with Technobit Asic & USB Erupters (AntMiners) ? |
|
|
|
|
|
NoahWL1
|
|
June 01, 2015, 09:42:20 PM |
|
Would you be able to plug in an Antminer U1/U2 and use it with the CGMiner interface?
|
|
|
|
|
Zich (OP)
Legendary
Offline
Activity: 1190
Merit: 1000
|
|
June 02, 2015, 12:44:03 AM |
|
Would you be able to plug in an Antminer U1/U2 and use it with the CGMiner interface?
No, all non technobit miner driver is not compile on the firmware. |
|
|
|
|
|
NoahWL1
|
|
June 02, 2015, 12:50:50 AM |
|
Would you be able to plug in an Antminer U1/U2 and use it with the CGMiner interface?
No, all non technobit miner driver is not compile on the firmware. Is there any other firmware that can do this? Like the original OpenWRT software? If not, are there any other low-cost low-power consumption Antminer U1/U2 controllers out there besides the Raspberry Pi that you know of? |
|
|
|
|
Zich (OP)
Legendary
Offline
Activity: 1190
Merit: 1000
|
|
June 02, 2015, 08:22:00 AM |
|
Would you be able to plug in an Antminer U1/U2 and use it with the CGMiner interface?
No, all non technobit miner driver is not compile on the firmware. Is there any other firmware that can do this? Like the original OpenWRT software? If not, are there any other low-cost low-power consumption Antminer U1/U2 controllers out there besides the Raspberry Pi that you know of? No, as far as i know. You can try to compile the cgminer for openwrt. I never try since it's out of my league  |
|
|
|
|
|
NoahWL1
|
|
June 02, 2015, 12:46:01 PM |
|
Would you be able to plug in an Antminer U1/U2 and use it with the CGMiner interface?
No, all non technobit miner driver is not compile on the firmware. Is there any other firmware that can do this? Like the original OpenWRT software? If not, are there any other low-cost low-power consumption Antminer U1/U2 controllers out there besides the Raspberry Pi that you know of? No, as far as i know. You can try to compile the cgminer for openwrt. I never try since it's out of my league Alright I think I'll just go with a Raspberry Pi since it seems to be the only low power consumption controller. |
|
|
|
|
wareck
Member
Offline
Activity: 238
Merit: 10
|
|
February 13, 2016, 04:29:15 PM |
|
Nice job !
Is it possible to have source code ? (i wants to make my own firmware...)
thanks
|
|
|
|
|
|
|
|
