miniZv2.3c Equihash144,5 125,4 210,9 150,5 192,7 Beam ProgPoW Ethash CFX KLS PYI

[dedizonesv2]

Hi miniZ,

I'm running a total of 9 rings, 88 cards. All cards are RTX 3060 and I'm getting 40mh stable. While everything is going very well for the first days, I suddenly start to get rejected shares. Not all rings have the same problem. But all hardware is the same. What is the reason?

Extra config arguments:
--dag-fix



Cheers

same problem with 3060 Ti and 3070 difficult to have 60.50mhz and a lot of stale / badshare worries

Hi multimesut, dedizonesv2,

How was it? Did it start rejecting (all?) after a certain time, or it was only during a certain period and then it was ok again?

Dou you have the miniZ log of when the rejected shares started?

We're also improving the 3070 Ti.

Thanks a lot for the feedback.
We'll investigate this.
Cheers

Hi miniZ,

For example, 3 out of 8 rings have problems. (All of rings have problems, but not at the same time.) rejected shares are constantly increasing. Restarting the system fixes it. If there is a log you want, if you specify the path, I can get it. (hiveos)

Cheers

exactly, moreover we do not know which parameter to have an OC? I put the auto mode but it runs in a loop ... and the watt consumption not optimized at all.

I think you should optimize for RTX

[miniZ]

Hi miniZ,

For example, 3 out of 8 rings have problems. (All of rings have problems, but not at the same time.) rejected shares are constantly increasing. Restarting the system fixes it. If there is a log you want, if you specify the path, I can get it. (hiveos)

Cheers

Hi multimesut,

You can add --logfile=/home/user/miniz.log to your command line.

Then you only need to check that folder
This should do it.

Have you tried using a different pool? It can be that with some other pool you'll get less rejects. Do let us know, we may need to give it a look.

Thank you for your feedback.
Cheers

[miniZ]

exactly, moreover we do not know which parameter to have an OC? I put the auto mode but it runs in a loop ... and the watt consumption not optimized at all.

I think you should optimize for RTX

Hi dedizonesv2,

Sorry, we are not sure we understand your message/issue well.
Could you clarify? What is running in a loop?

The OC settings that you do not know, do they refer to the 3070?
You can start by lowering the power and then make adjustments to the core/mem clocks. Give it some time in between adjustments and access the performance and stability od the setting. 

Could you tell which pool are you using? It can be that with some other pool you'll get less rejects. But do let us know, we may need to give it a look.

Thanks.
Cheers

[multimesut]

exactly, moreover we do not know which parameter to have an OC? I put the auto mode but it runs in a loop ... and the watt consumption not optimized at all.

I think you should optimize for RTX

Hi dedizonesv2,

Sorry, we are not sure we understand your message/issue well.
Could you clarify? What is running in a loop?

The OC settings that you do not know, do they refer to the 3070?
You can start by lowering the power and then make adjustments to the core/mem clocks. Give it some time in between adjustments and access the performance and stability od the setting. 

Could you tell which pool are you using? It can be that with some other pool you'll get less rejects. But do let us know, we may need to give it a look.

Thanks.
Cheers

Hi miniZ,

I can't get invalid share in other apps in the pool i'm using. Again, my different rings, which are rtx 3060, work with the same pool, different program.

I got the log file. I sent it as a private message.

Thanks, Cheers

[styleshifter]

miniZ was mentioned in some of the biggest German IT news today:

https://www.heise.de/news/Ethereum-Mining-Erster-Miner-umgeht-Nvidias-Hashrate-Bremse-6151593.html

https://www.golem.de/news/miniz-erster-miner-knackt-nvidias-ethereum-drossel-2107-158553.html

[waggy459]

ASUS Dual 3060, O12G-V2 so it's an LHR card.  I'm running on a very old motherboard, so let me know if that's likely the issue.

HiveOS newest ver, MiniZ 1.8y4, NVidia driver 460.84, I had a problem installing the 460.39.  Card OCs set to fan 80, core -150, mem 2700, PL 120.  Runs only at 6.5-10mh and not much more than that.  The motherboard is out of an HP z210, I'm plugged in through a riser to a slot that says in the specs X16, but PCIe 2.0.  I've tried this slot and the x4 slot next to it with same results.

Any thoughts to try?  I do not have any switches added to the miner in the flight sheet, I see some stuff with 150,0 and other things, are any additional parameters needed to run these LHR cards at full hash rate?

Added:  I don't have a dummy plug, but I do have an hdmi to vga converter cable plugged into the card that usually fools the card into thinking something's plugged in.

[waggy459]

ASUS Dual 3060, O12G-V2 so it's an LHR card.  I'm running on a very old motherboard, so let me know if that's likely the issue.

HiveOS newest ver, MiniZ 1.8y4, NVidia driver 460.84, I had a problem installing the 460.39.  Card OCs set to fan 80, core -150, mem 2700, PL 120.  Runs only at 6.5-10mh and not much more than that.  The motherboard is out of an HP z210, I'm plugged in through a riser to a slot that says in the specs X16, but PCIe 2.0.  I've tried this slot and the x4 slot next to it with same results.

Any thoughts to try?  I do not have any switches added to the miner in the flight sheet, I see some stuff with 150,0 and other things, are any additional parameters needed to run these LHR cards at full hash rate?

Added:  I don't have a dummy plug, but I do have an hdmi to vga converter cable plugged into the card that usually fools the card into thinking something's plugged in.

Update after a couple more minutes research, set PL to 100 and hash rate started climbing, I'm was at around 25-26.  Now messing around with absolute core clock instead of offset, I'm at 1250 now and ~27mh.  So I guess I'll keep messing around with it, but this is pretty good now, only running ~90W.

Add:  I settled on 1375 locked core, 2700 mem, 100W PL and 80% fan.  Seems steady at 33mh at 98watts.  I'm happy enough with this for now, if further development hits and this gets better great, but I can reasonably ROI this card now, it was at msrp. 

[Ammereys]

ASUS Dual 3060, O12G-V2 so it's an LHR card.  
I settled on 1375 locked core, 2700 mem, 100W PL and 80% fan.  Seems steady at 33mh at 98watts.  I'm happy enough with this for now, if further development hits and this gets better great, but I can reasonably ROI this card now, it was at msrp. 

Try 0 1447 2550 120 I get 35+ with the V2

[waggy459]

ASUS Dual 3060, O12G-V2 so it's an LHR card.  
I settled on 1375 locked core, 2700 mem, 100W PL and 80% fan.  Seems steady at 33mh at 98watts.  I'm happy enough with this for now, if further development hits and this gets better great, but I can reasonably ROI this card now, it was at msrp. 

Try 0 1447 2550 120 I get 35+ with the V2

Thanks!  With those numbers I'm getting right at 35mh at ~104W.  Not too bad given I didn't even think I'd be mining eth with this card, turned out better than expected.

[miniZ]

Hi miniZ,

I can't get invalid share in other apps in the pool i'm using. Again, my different rings, which are rtx 3060, work with the same pool, different program.

I got the log file. I sent it as a private message.

Thanks, Cheers

Hi multimesut,
First of all, sorry for taking a bit longer than usual to reply.

Thank you for the log!

We are a bit puzzled with your issue. The problem seems to affect your GPUs 5, 7, and 10.

We are not sure yet, of that can be causing this. Could you try to adjust a bit your OCs for these GPUs? This will help us to understand if the issue is related to the OC settings.

Let us know if this helps, or if it continues generating invalid shares.
Cheers

[miniZ]

miniZ was mentioned in some of the biggest German IT news today:

https://www.heise.de/news/Ethereum-Mining-Erster-Miner-umgeht-Nvidias-Hashrate-Bremse-6151593.html

https://www.golem.de/news/miniz-erster-miner-knackt-nvidias-ethereum-drossel-2107-158553.html

Hi styleshifter,

Thank you for letting us know

Cheers

[miniZ]

ASUS Dual 3060, O12G-V2 so it's an LHR card.  
I settled on 1375 locked core, 2700 mem, 100W PL and 80% fan.  Seems steady at 33mh at 98watts.  I'm happy enough with this for now, if further development hits and this gets better great, but I can reasonably ROI this card now, it was at msrp. 

Try 0 1447 2550 120 I get 35+ with the V2

Thanks!  With those numbers I'm getting right at 35mh at ~104W.  Not too bad given I didn't even think I'd be mining eth with this card, turned out better than expected.

Hi waggy459,

Thank you for your message.

Good that you managed to get it running more stable.

Thanks to Ammereys for the suggestion!

Cheers

[multimesut]

Hi miniZ,

I can't get invalid share in other apps in the pool i'm using. Again, my different rings, which are rtx 3060, work with the same pool, different program.

I got the log file. I sent it as a private message.

Thanks, Cheers

Hi multimesut,
First of all, sorry for taking a bit longer than usual to reply.

Thank you for the log!

We are a bit puzzled with your issue. The problem seems to affect your GPUs 5, 7, and 10.

We are not sure yet, of that can be causing this. Could you try to adjust a bit your OCs for these GPUs? This will help us to understand if the issue is related to the OC settings.

Let us know if this helps, or if it continues generating invalid shares.
Cheers

Hi miniZ,

yes, this is very interesting. Thanks for information. I lowered the OC settings. I set the RAM usage to 2200. I will watch it again.

Cheers

[MasterB1802]

Hi,

maybe someone is here with same problems.

Running rtx3060 and rtx2070 super since months:

- rtx3060 @ 42MH/s (1st PCEe 16x)
- rtx2070Super @47MH/s (2nd PCIe 16x)
- Nvidia Driver 470.05
- both with Excavator v1.7.1d  (Nicehash)

Additionally I got a rtx3090FE and changed the pci slots

- rtx3090 @115MH/s (1st PCIe 16x)
- rtx2070Super @47MH/s (riser @ PCI 1x)
- rtx3060 @25MH/s (riser @ PCI 1x)
- all with Excavator v1.7.1d (Nicehash)

so I tried to use Nicehash only with rtx3090 and rtx2070Super and miniZ with rtx3060


I don't get more than 21MH/s with miniZ.
Tried v1.8y3, 1.8y4rc1 and several nvidia driver (470.05, 461.40, 471.68)

Could it be a hardware problem with riser on pci or software problems with wrong driver <-> miniz version?

Someone an idea?

[dragonmike]

Has anybody got a good clock/power settting for 125,4 on 3060 Ti's by any chance?

Running +250 core, -1000 mem (HiveOS) @ 125W gives roughly 50 sol/s. No idea if that's good.

[pit55]

Hi in HIVEOS cannot chose the kawpow algorithm on the menu.
If i start by hand (sample in faq) i can use it.
I love your miner maybe you can give the --par kawpow parameter and after hiveos have a nice template to work.
Thank you

https://i.ibb.co/ZBW98W3/Ke-pernyo-foto-2021-11-12-11-46-37.png

[beisbol349]

Hi All - I am encountering a memory access error that crashes the miner after 12+ hours of operation. I am mining flux (equihash(125,4)) to na.minerpool. I believe the 2080 ti i recently added is the culprit, although the miner reports GPU 0 (a 2080 that has been running stable for days). My overclock settings on the 2080 ti are PL 70, Core Clock +140, Memclock -502 (max), Fan 70%.

What are your thoughts on what the issue is? Can the miner be modified to re-start automatically?

[sxemini]

Hi All - I am encountering a memory access error that crashes the miner after 12+ hours of operation. I am mining flux (equihash(125,4)) to na.minerpool. I believe the 2080 ti i recently added is the culprit, although the miner reports GPU 0 (a 2080 that has been running stable for days). My overclock settings on the 2080 ti are PL 70, Core Clock +140, Memclock -502 (max), Fan 70%.

What are your thoughts on what the issue is? Can the miner be modified to re-start automatically?

Try with stock settings. I think core clock +140 is to much. By the way lower PL is not recommend in my opinion. Set a fix voltage is more suitable. The card clock down automatically and the voltage and core clock don´t jump up and down.

[bitexecute]

im having trouble getting stable hash rate, the hash rate drops after some days with my 1070 laptop gpu

[PeaMine]

Is there a link that is WGET friendly for Linux?