thierry4wd (OP)
|
|
February 08, 2019, 07:40:06 PM |
|
No I can not ... this is a setting ONLY for me ... depending on your environment and your fan it could cause you a lot of trouble! so sorry ...
Ps : you are tested this ? what your consuption at what frequency at your wall ?
|
|
|
|
|
|
|
|
|
"This isn't the kind of software where we can leave so many unresolved bugs that we need a tracker for them." -- Satoshi
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
geolyk
Newbie
Offline
Activity: 21
Merit: 2
|
|
February 09, 2019, 06:56:15 AM Last edit: February 10, 2019, 02:17:33 AM by frodocooper |
|
I will test it today. I don't care about the power . I only need silence . The miner is outside .but is noise. I have put a firmware atm with dev fee . But is doing up and down the fan speed every time is going to my pool and dev pool . So from silence to noise and back again
i tested but i see that one temp sensor is not working? Temp(Chip1) all are 0 fans are 3000 rpms and 4200 rpms temp on chip2 is 90 max
|
|
|
|
thierry4wd (OP)
|
|
February 10, 2019, 11:57:22 AM |
|
hi , temp(chip1) show all 0 is normal , is bad code on original firmware ... i have "coded" a correctif for this if you interessed Normaly, with my Bmminer, your miner is running with lower noise compare to original bitmain (or custom) ... you confirme this ?
|
|
|
|
geolyk
Newbie
Offline
Activity: 21
Merit: 2
|
|
March 08, 2019, 02:06:34 PM Last edit: March 08, 2019, 11:39:23 PM by frodocooper |
|
my miner is still noise....i cant make it more silence? i dont care if is running on lower h/s i want the fan to be arround 3000rpms
cant understand why this is so noise ...i have l3+ and d3 and there realy silent
|
|
|
|
thierry4wd (OP)
|
|
April 15, 2019, 07:44:10 AM Last edit: April 15, 2019, 11:13:26 PM by frodocooper |
|
thank you for your share!
You try it ? please return your experience and your power at wall
|
|
|
|
emran6630
Newbie
Offline
Activity: 1
Merit: 0
|
|
August 25, 2019, 02:17:44 PM Last edit: August 26, 2019, 01:41:29 AM by frodocooper |
|
Can anyone reupload this file? I cant download it.
|
|
|
|
rre_za
Newbie
Offline
Activity: 5
Merit: 0
|
|
September 22, 2019, 08:49:28 AM |
|
Hi everyone, I decided to share my Bmminer edit for T9+ (and tested), here are the mods: - Reduction of the consumption of 300W approximately !!! - Delete Pic Flash ERROR (now working) - Custom Fan Management, run with VERY LOWEST NOISE !!! The usual procedure: Rename the Bmminer Bmminer-Old in / USR / BIN to be able to restore it if needed .... Then replace it with mine, do not forget to give it the right to execution "RWXR-XR-X" Download: http://www.k-upload.fr/afficher-fichier-2018-11-17-1cfabf3eabmminert9eco.zip.htmlAll the reviews and your comments are welcome !!!!!! And for a small donation do no hesitate to contact me in PV Thanks !!! link is not working.
|
|
|
|
thierry4wd (OP)
|
|
September 22, 2019, 09:32:48 AM |
|
Hi , my "mod" is now expired, no contain AsicBoost, no interest at this time... Now bitmain release T9+ 2019 firmware with multi option and eco mode, is very good for T9+ (only close SSH port is bad) , i thinks not better existing mod for eco ... 10.5TH at arround 950w ... is very good for T9+ ... Thanks for interesting by my mod
|
|
|
|
rre_za
Newbie
Offline
Activity: 5
Merit: 0
|
|
September 22, 2019, 10:20:41 AM |
|
Hi , my "mod" is now expired, no contain AsicBoost, no interest at this time... Now bitmain release T9+ 2019 firmware with multi option and eco mode, is very good for T9+ (only close SSH port is bad) , i thinks not better existing mod for eco ... 10.5TH at arround 950w ... is very good for T9+ ... Thanks for interesting by my mod t9+ with 2019 firmware achieves 10.5TH around 950w !? thats very nice
|
|
|
|
thierry4wd (OP)
|
|
September 22, 2019, 10:29:08 AM |
|
But warning, is not possible to downgrade after upgrade... return to original firmware is not possible !!!! (but only possible, for easy, with SdCard) with pleasure
|
|
|
|
|