intron
Sr. Member
Offline
Activity: 427
Merit: 251
- electronics design|embedded software|verilog -
|
|
May 15, 2014, 07:28:28 AM |
|
Thats very nice Intron. Does it get hot with 10 Hex*furys? Yes:-) I used three fans to cool the set-up.
|
|
|
|
|
|
|
"Governments are good at cutting off the heads of a centrally
controlled
networks like Napster, but pure P2P networks like Gnutella and Tor seem
to be holding their own." -- Satoshi
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
LordTheron (OP)
|
|
May 16, 2014, 09:32:52 AM |
|
Thats very nice Intron. Does it get hot with 10 Hex*furys? Yes:-) I used three fans to cool the set-up. Building "Hex flower" out of RF hub . Curious if the board will handle the current for 19 Hex*furys... Thats almost 40A
|
|
|
|
ninjaboon
Legendary
Offline
Activity: 2114
Merit: 1002
|
|
May 19, 2014, 06:04:44 AM |
|
Is the HEX•FURY 11+Gh/s USB Stick Miner still in stock?
|
|
|
|
|
Zeta0S
Legendary
Offline
Activity: 1890
Merit: 1031
|
|
May 23, 2014, 12:03:58 AM |
|
Is there a other brand whit miners like this?
|
|
|
|
TheRealSteve
|
|
May 23, 2014, 12:59:33 AM |
|
Is there a other brand whit miners like this?
Check out my StickMiners - Where FUN > ROI thread. Note that right now, the NF6 (another 6xBitFury chip model, but by the designer of the NanoFury) is missing as it's not for sale anywhere as of yet (currently in limited production, as far as I know).
|
|
|
|
GoogleBit
|
|
May 23, 2014, 01:13:59 PM |
|
I got my HEX FURY today. Ordered at the 20.May, I got it 3 days later, delivered to Switzerland from UK. Thanks guys... I plugged it in my DELL Precision M6700 with USB 3.0, installed the driver, and started cgminer. Connected direkt to the Notebook, or using the split cable with my extra 5.2V/3.0A power adapter, makes no difference. The HEX FURY get's over 80C in less then 2 minutes. That's the moment I unplug and burn my fingers. In cgminer it get 12.6 GHs right away. Anyone made the same experience ? Update: Got answer from ASIC Runner in minutes, WOW, cool ;-)
You must use powered usb hub with 2A power per port or the injector cable. Also make sure that you use a small fan to keep your Hex below 82C. It is normal that is getting hot, depending what ambient temperature you have.
Any small fan will do the job well, all it needs is a bit of air circulation at the side of heatsink. not much tho. Don't worry there is nothing wrong with it, it gets hot as any other device passively cooled
|
|
|
|
-ck
Legendary
Offline
Activity: 4102
Merit: 1632
Ruu \o/
|
|
May 23, 2014, 01:15:14 PM |
|
I got my HEX FURY today. Ordered at the 20.May, I got it 3 days later, delivered to Switzerland from UK. Thanks guys...
I plugged it in my DELL Precision M6700 with USB 3.0, installed the driver, and started cgminer. Connected direkt to the Notebook, or using the split cable with my extra 5.2V/3.0A power adapter, makes no difference. The HEX FURY get's over 80C in less then 2 minutes. That's the moment I unplug and burn my fingers. In cgminer it get 12.6 GHs right away. Anyone made the same experience ?
Sounds about right. They need active cooling...
|
Developer/maintainer for cgminer, ckpool/ckproxy, and the -ck kernel 2% Fee Solo mining at solo.ckpool.org -ck
|
|
|
vayvanne
|
|
May 23, 2014, 10:18:47 PM |
|
GoogleBit What is average speed without fan (with cgminer throttling)?
|
|
|
|
|
LordTheron (OP)
|
|
May 28, 2014, 10:30:50 AM |
|
New Deal of the day is store, Hex fury only £99 and Group Deal on Yellowjacket £10 only! Visit www.asicrunner.com
|
|
|
|
|
|