|
Trouble Shooting!
Please go to the 1st page of this thread!
For a quick notes.
If your miner is missing a white sticker with an IP address printed, you can change your computer's ip setting to.
IP: 192.168.2.254
Subnet:255.255.255.0
Gateway: 192.168.2.1
DNS: 8.8.8.8
Then physically connect ANTMINER to your laptop via Ethernet cable, open the web browser, start trying the address, 192.168.2.1 all the way to 192.168.2.253. More than likely your ip is somewhere between .101 and 253 but if you want to be so anal about it, please try one by one from .1
Other option, set your router setting to
Gateway: 192.168.2.1
DHCP
Subnet: 255.255.255.0
Connect your computer to the router under auto IP config, the. Run anIP scanner software while your AntMiner is connected to your router by the Ethernet. The IP scanner will find your antminer precongigured IP address without have to reset the miner or send it back for the replacement or repair!
If your miners showing average of higher than 169gh and there is no xxxxx on the ASIC chip status but BTCGUILD status shows you 160's or so of hashing number, that could be simply just what was transmitted from your miner over to the network and there is always a slighter number difference. You may also see it higher number than what the antminer's status page shows.
If you see some "x" on the status page, double check your PSU setup and wiring!
Then turn the unit back on and check the status. You may have to reboot a few times to have all 'o' but soon or later it should turn all'o'. Once in a while, it may shows ' 'but as long as it's random and not so frequent, you don't have to worry about too much!
|
|
|
|
Hey, if enough of you are interesting and would t mind funding the myth buster trip, I will see what schedule is available! So far Lotsof people called Bitmain a scam but I was able to verify! With current market, total of 1.1 BItcoin should cover the cost on the last minutes flight! Any donors? 0.01 BTC donation x 100 member won't be too much to ask, if you are debating imago to invest in the next generation ASIC Specially it's so hard to decide who would more than like to produce. Knc and black arrow are known to deliver from the last releases! |
|
|
|
I will! But it could be a brick sale!  Sushi and I will be doing the next batch when BITMAIN confirms they have enough products waiting to be shipped.
Good news. Sushi has my email but pls do let me know when. Thanks! |
|
|
|
|
I will let you know once the domestic ship group buy for the U1 in the land of freedom (USA)
Also for Canada and Japan so you guys in those countries may not have to worry about the custom! It could cost a bit more though as quantity shipment can't avoid the customs due... & not to mention the double shipping. Original shipping fee and the domestic shipping but I see benefits for the buyers as they will receive it sooner and may able to use the local fiat!
Stay tuned!
|
|
|
|
Yes! This do really works. however, the S1 is designed to run optimum at 180gh range and over clocking may void your warranty as you have to modify the config file of the unit. CAUTION!!! Without the proper cooling and the power supply, it could hurt your lovely Ant! Thanks for Goxed to making the list! It does really work! |
|
|
|
Not yet but if you could shoot me an email at joshmon@e-mail.ph. I will keep you inform as soon as I know a group buy, auctions I, last minutes cancellations and other I stock ASIC sales elsewhere! Sushi, any word when the next batch of these will be coming round the mountain? thx!
|
|
|
|
Thanks for participating in the groou buy and sorry about the postal code screw up on my part! Great to hear its hashing away at 200gH more bung for the money! It's a beautiful thing... China to Connecticut in 2 days, set up in 45 minutes (had to find my wire strippers, took a bit) and overclocked in about 10 seconds. Happily hashing away at 200Ghz. Huzzah! Thanks again sushi for taking this over.
|
|
|
|
Would you kind enough to post a close up of your PSU to be able to see the brand? Also close look on your wire connections! Also if the wires are getting hotter or not. Also the hard reboot the power cycle and take some sample status on the ant miners in a few hours time frame. Such as 39 minutes between or an hour between? Thank you! my 2 have arrived and are hashing. only concern is they are only hashing around 140 - 145 gh/s according to the web configuration, but only shows 120+ on btcguild. some of the asic's are showing an X in the asic status. temp's are showing below 50. who do i need to get with for support/returns/replacement/etc?
Hi can you show us your stats ?? I have got between 1-4 x . This is connected with power supply. You should check wires, try reboot machine. let us know. I already reboot, and lowered my x from 4 to 1 on blade nr.1. i did reboot and am getting a bit better, but still 10% less than 180gh/s. and as you can see the 2nd one is worse than the 1st with almost a full row of X's. 1st -  2nd -  btcguild stats -  |
|
|
|
Please try the hard power cycle with at least 39 seconds of break between! And the. Check the ASIC status page and see if there are any "x" instead of 8 "0"s The perfect machines may see x time tori shut that should be just random locations. If problem persist, please email me the picture of your power supply and how you wire the power cables and a few screenshots of the status pages from a few hours between as the samples. The could t on a BTCGuild differs time time but in a kong term average should equal out. If the btcguild speed seems too low, try other pools and see! The control panel shows the real hashing rate as btcguild shows what they received from your ant is the network, so if there are traffic issues, it could count a bit lower. Also I have seen the gh rate higher than my test machines reported... Joshmon@e-mail.phmy 2 have arrived and are hashing. only concern is they are only hashing around 140 - 145 gh/s according to the web configuration, but only shows 120+ on btcguild. some of the asic's are showing an X in the asic status. temp's are showing below 50. who do i need to get with for support/returns/replacement/etc?
|
|
|
|
I do! With a grapefruit chaser I am waiting for one more unit as well  . Ok who want a shoot of vodka ?  |
|
|
|
Glad to see you got the hands on these units!!  Thank you for supporting the group by, if you could shoot me a email to joshmon@e-mail.ph, I will keep you on the list for any future group buy, auctions and any last minute cancellation or extra units! Sushi stuck in warehouse in Ca - status says "Awaiting release from Clearance/Government Agency."
|
|
|
|
I'm sorry to hear that! The sorting facility guys must had a bad day I am waiting for 2 units , but
first unit is out for delivery today
second :The scheduled connection was missed / Expired-unable to resolve exception .
OMG... the same times, one get on the truck, the second one no ... ??
|
|
|
|
|
Just finished sending all of you the tracking number. I'm sorry for the delay.
SUSHI
|
|
|
|
|
Thank you for waiting!
Tracking Numbers are IN!!! Just got them. I will be PM or e-mailing you the tracking number in the next hour or so. I'm leaving you guys a feedback.
Talk to you later!
|
|
|
|
|
Thank you guys for participating in the auction.
I double checked the list and my copy & paste didn't screw up the data!
Also, please disregard the numbers shown in "Amount Before Discount" Bitmain will advise you what your discount is.
The List I used are to keep the place and the total number of units available for the record keeping purpose only!
SUSHI
|
|
|
|
Thank you Elastic Band! I'm verifying the list now, but this is what I have so far.... | Username | Quantity | | Bidding Price | | Units left | | Amount | Payment address | Amount Before Discount | | HorseRider | 1 | | 6.00 | | 119 | | 6 | | 3 | | geoloudon | 2 | | 4.75 | | 117 | | 9.5 | | 6 | | Airwhale | 1 | | 4.75 | | 116 | | 4.75 | | 3 | | smartbrain | 1 | | 4.50 | | 115 | | 4.5 | | 3 | | nairb131 | 3 | | 4.50 | | 112 | | 13.5 | | 9 | | keefe | 2 | | 4.50 | | 110 | | 9 | | 6 | | pmagid | 1 | | 4.50 | | 109 | | 4.5 | | 3 | | Goxed | 2 | | 4.50 | | 107 | | 9 | | 6 | | resningpocdi | 12 | | 4.50 | | 95 | | 54 | | 36 | | torusJKL | 3 | | 4.50 | | 92 | | 13.5 | | 9 | | greaterninja | 3 | | 4.50 | | 89 | | 13.5 | | 9 | | AndiDC | 2 | | 4.50 | | 87 | | 9 | | 6 | | arorts | 10 | | 4.50 | | 77 | | 45 | | 30 | | bones | 2 | | 4.50 | | 75 | | 9 | | 6 | | canford | 1 | | 4.50 | | 74 | | 4.5 | | 3 | | fizboz | 1 | | 4.50 | | 73 | | 4.5 | | 3 | | conv3rsion | 3 | | 4.50 | | 70 | | 13.5 | | 9 | | Ridicuss | 1 | | 4.50 | | 69 | | 4.5 | | 3 | | yuancraft | 1 | | 4.50 | | 68 | | 4.5 | | 3 | | spiccioli | 2 | | 4.50 | | 66 | | 9 | | 6 | | gravito | 3 | | 4.50 | | 63 | | 13.5 | | 9 | | semaster | 3 | | 4.50 | | 60 | | 13.5 | | 9 | | xwr213 | 1 | | 4.50 | | 59 | | 4.5 | | 3 | | dentldir | 1 | | 4.25 | | 58 | | 4.25 | | 3 | | erem | 5 | | 4.25 | | 53 | | 21.25 | | 15 | | djjacket | 1 | | 4.25 | | 52 | | 4.25 | | 3 | | slastar | 10 | | 4.25 | | 42 | | 42.5 | | 30 | | ouwe | 15 | | 4.25 | | 27 | | 63.75 | | 45 | | xstr8guy | 1 | | 4.25 | | 26 | | 4.25 | | 3 | | bitwhizz | 9 | | 4.25 | | 17 | | 38.25 | | 27 | | lubah | 1 | | 4.25 | | 16 | | 4.25 | | 3 | | r7970 | 1 | | 4.25 | | 15 | | 4.25 | | 3 | | miter_myles | 1 | | 4.25 | | 14 | | 4.25 | | 3 | | resort | 1 | | 4.25 | | 13 | | 4.25 | | 3 | | joemde | 13 | | 4.25 | | 0 | | 55.25 | | 39 |
|
|
|
|
|
List from #518 seems to be it... It will go to Bitmain for the final process.
|
|
|
|
YEP, I see it now!! The other post only showed it was within 3 minutes, but I do see "4" seconds OVER!! WTF, the last bid was @ Today at 12:54:45 PM by xwr213
Auction ended at 01:14:45
Elastic's bid was at Today at 01:14:59 PM
|
|
|
|
|
no more playing bids please!
|
|
|
|
|
let me update the list... un moment por favor...
|
|
|
|
|
Show Posts
