Might be a dumb question but here goes. I have about 100 erupters, want only 50 to show in a window. All are connected to the same computer (Win 7 x64). Using cgminer 3.6.6. Reason for this is I use these to mine smaller SHA256 alts. This way I can mine two coins at once. Banks of many erupters seem to keep up with fast coins quite well, if set up correctly. Thought it could be done by specifying com port range in config but winusb driver does not seem to assign com ports to erupters.
|
|
|
Bought some more. Helipotte; 1.75; BEx50+hub 16AP5qJH6urahX5KxvMTySFM6oGhjSkXWe Transaction ID: 19d0f0543eb7cdb93d742a57252ea180e1649759d3009b562484e55d95d69e26 Thanks! Canary, could you send different colors? Last order was 30 black and 20 red. If you have them.
|
|
|
The strange hashrate difference is happening again. Been monitoring it for about an hour. I have low rejects and HW errors but pool is reporting hashrate to be about 15%-20% lower than actual. I first saw this happening about a week ago. Will this loss of hashrate affect round payout? Could the pool operators perhaps shine some light on this?
|
|
|
So does anyone have instructions on how to wire an ATX connector to the above PSU in pics?
I have not seen the PSU but I suspect you could just connect all of the red wires to V+, all of the black wires to V-. The rest of the wires could be removed from the 24 pin connector or ignored. I think they all float on the hub side except for the green wire that turns on the ATX power supply. This wire is even mute with a dedicated 5V PSU. I think I would rather wire in a switch on the 5V PSU.
|
|
|
Just updated prices on blades.
Also, there are no more USBs available from the manufacturer. Whatever remains on hand at resellers is it folks. Once they're gone, they won't be restocked or made again.
I still have plenty on hand with good color selection and offcourse 50 units include the 49 port USB hub.
Are the blades still in production? Or are they stopping production on all BE100 based miners. Maybe gearing up for V2? if they made a new stick they need a different chip. even 1gh-1.5gh stick with power at 2.5 to 3 watts would work. V2 = smaller process node, same design. Maybe then, higher clocks and/or x2 chips per stick would achieve 1-1.5Gh.
|
|
|
Just updated prices on blades.
Also, there are no more USBs available from the manufacturer. Whatever remains on hand at resellers is it folks. Once they're gone, they won't be restocked or made again.
I still have plenty on hand with good color selection and offcourse 50 units include the 49 port USB hub.
Are the blades still in production? Or are they stopping production on all BE100 based miners. Maybe gearing up for V2?
|
|
|
philipma1957 has found this PSU: http://www.mcmelectronics.com/product/58-12860 use code afc909 get a 15% discount to under 14 bucks plus shipping! It should be tested Wed/Thur to know for sure, but from the specs, it looks to be a great PSU to power one of these hubs (for the $). these are a fail I blew up a pair of them at about 30 sticks what blew? the PSU, the wire or the plug? Its says its to have 36amps on the 5v side so should have powered more than 30? Most likely the output diode on the 5V rail. Could of been the switching mosfet(s). I have seen some PSU's come in my shop that claim very large outputs but I open them only to find parts capable of maybe half. Under normal conditions where max load it demanded maybe .5% of the time this is OK. Put a constant 80-90% load on it... poof!
|
|
|
Looks like a 4 pin phoenix connector. Not absolutely sure. Can check one of my blades later. I'll post a link when I'm sure.
|
|
|
I hope these hubs have an internal DC-DC converter and don't use the 5V rail exclusively. This is unlikely due to cost constraints.
|
|
|
Have 4 Ztex clones. Hashing right now @3500Mh. Reasonable offers accepted.
|
|
|
Purchased.
Helipotte; 1.75; 50+hub; 16AP5qJH6urahX5KxvMTySFM6oGhjSkXWe
Transaction ID: 9b438e5ea25598497d6c29b3c283dc789bfa11624e23a4bb282c591cdd44f04e
Thanks!
|
|
|
I'm getting good speed estimates today. I haven't left the pool however. Within 1% of my locally reported hashrate with increasing estimated round payout. Wish this round would end though.
|
|
|
Something strange has happened to me, mining with this pool. Have ~105gh, been mining for about 4 days. Pool reports ~102gh, all is normal. Leave pool to mine alt for about 10-15 min, reported rate drops to about 70gh. This is normal to. Come back to pool with full 105gh, mine for about 45 min. VERY low rejects (.22%), pool reports 87gh. This is after mining for 45 minutes. Question is, where did 18gh go? 45 minutes should be enough time for full hashrate to be reported. Reported rate is NOT going up. Is this a bug? This has happened on more than one occasion. Seems strange. BTW Love this pool. Wish more people would mine here! Edit: 1 hour of mining, it just corrected! 102Gh reported.
|
|
|
Not able to post anything on bitmit now. Please fix the system.
Please try again, works fine now. Expected server maintenance about 1-2h in ca 8 hoursStill can't post anything. Trying to communicate with a seller. Please fix. are you trying to send pm? That's working for sure, then it's on your end. Trying to send message through message board. Click send, nothing happens. Refesh, message not posted. Was sending messages last night from same computer (no changes). Been trying all day.
|
|
|
Not able to post anything on bitmit now. Please fix the system.
Please try again, works fine now. Expected server maintenance about 1-2h in ca 8 hoursStill can't post anything. Trying to communicate with a seller. Please fix.
|
|
|
Got my blades and USB's today. Love the "Peanuts" Canary uses! Now I have hundreds of little foam miners! Great job getting this stuff here fast BTW.
|
|
|
Helipotte 2, 4.10, 16AP5qJH6urahX5KxvMTySFM6oGhjSkXWe
Helipotte 5, 0.35, 16AP5qJH6urahX5KxvMTySFM6oGhjSkXWe
Thanks!
|
|
|
Why do the new blades have 16 spots for surface mount electrolytics that are unpopulated? Could they run faster or have better stability with them (cleaner power)? Was this a design decision made for cost reduction? If you added these could you overclock to old blade speeds (12Gh+)? Just curious really.
|
|
|
Helipotte; 2; 8; 16AP5qJH6urahX5KxvMTySFM6oGhjSkXWe ID e7d70f8404063f7ead9c9aa474d9c39c4cd212be13d4e894b3b6037e17e25217 Label sent.
|
|
|
Ok, lets try this coin for a change. I am tired of mining Bitcoin and Litecoin. 33000 mhash on its way What is that? 100 block erupters?
|
|
|
|