I have a U3 miner. I get a consistent 73gh/s out of it. I use a barrel connector wired to a molex 4 pin into a standard atx psu. Biggest difference is heavier wire to the plug. I am running cgminer 4.6.1 using the following line:  cgminer.exe --bmsc-options 115200:0.5 -o stratum+tcp://yourpool -u workername -p password --bmsc-freq 0B82 --bmsc-voltage 0800   I can actually get it to run higher than this and stable but the gh/watt ratio is bad so i don't.




if it matters. It is hooked to a Windows 7 64bit system via a usb 2.0 port. Oh, I did throw away the garbage usb cable I got with it and opted for a better quality one I had on hand too.

In response to be asked about a donation addy. I do not want donations. This was posted simply because i too had trouble and found something that works. If it works for you just enjoy your hash.

I have one of these and it works very well after some figuring out. First is the power source. That brick it came with just don't have big enough wires to supply it properly so I created a 4 pin molex to barrel connector lead for it and use a atx psu for it. Secondly is the command line for launching it.

cgminer.exe --bmsc-options 115200:0.5 -o url -u username -p password --bmsc-freq 0B82 --bmsc-voltage 0800

Here is a screen of my unit in action. You can judge for yourself.



I have 2 more coming (U3) that will be here middle of next week as well. Hope this helps.

Recently created and tested p2pool site.

Workers connect via port 9322 your addy is worker and any pw will work.

This started as a school project for me but decided to give it the ultimate test.

I welcome input for improvements. I am currently working on the fonts to make them more visible in certain areas.

Ok, so no this wallet I have is apparently not on the same blockchain. Downloaded it again today from the main site and still wrong chain. Not sure how this can be fixed but it does effect whether i will chance wasting more hash time at one of your pools. Sorry for that but I can't afford hits like this.

How do I verify what chain I am on if I have no block records to base off of? I am a little new to this part of things other than just loading the wallet and going.

I am running the new 2.2.0.o version of tekcoin wallet and yes it is fully synched. Atleast it says it is and shows 10 active connections. This was first time I ever mined tek so there is nothing in my wallet record wise other than the original addy.
I am re-installing it now and it is redownloading the blockchain. When it gets done I will try my wallet.dat to see if maybe it was just a glitch on my end.

I mined for awhile on tekcoin at your site. Kinda funny that it shows I was paid for all the blocks I found yet i never received a single coin. Yes, I checked my addy to make sure it was correct, "BrVwzEWjrjGdWsk9vB52ECiCAQbRzcPCkt". Not a single transaction ever came thru. Hopefully someone can look at this and explain to me what happened please.

A new p2pool node has been opened on the US Westcoast.

trc.getyourhashon.net at port 9322

your wallet addy is your worker name and any pw works

Has been test run with 3th on it and did well

Need to know what kind of device you are using.

I bought one of these from minersource and it gave me extreme grief getting it going. It is still falling short of rated hash but atleast i got it doing something half decent. Using the cgminer supplied by bitmain. Converted the driver to winusb. Modded power to a atx psu for more umph. Using this comand line in a bat file:

cgminer.exe --bmsc-options 115200:1 -o stratum+tcp://freicoin.us:4334 -u username -p password --bmsc-freq 0C82 --bmsc-voltage 0800