ANTMINER S7 is available at bitmaintech.com with 4.86TH/s, 0.25J/GH

[smaxz]

On a separate note has anyone found where you can enable/disable the S7/S5+ Controller boards Data port? It would be nice to either upgrade firmware and enable more than 3 data ports...

have you tried just soldering on new male connectors and hooking up boards? if you leave one board unpowered the miner does not leave ------- if i'm not mistaken is just appears blank. so it may be safe to assume scaling the system up is just a matter of physically adding the parts themselves.

[elrippo]

I just received my S7-F1 & it will not produce an ip address to configure my miner. It seems to be hashing on the default pool settings Bitmain configures, more profit for them while customers configure or try to configure their miners.

Following the instruction for the s7 pdf & downloading the Chinese version of ipreport the software always reports "has timed out start again" in Chinese, Gooble search translation.

I am sure the unit is mining because it goes full rpm on the fan & gives green LED on the controller board face. I do notice a red LED at rear closest to the ASIC boards, also red LED lights on the front of the ASIC boards. The unit produces heat, telling me it is mining somewhere.

There is a ‘Reset’ button on the right hand side of the Ethernet port, next to the green and red LED light. BTC Power on miner and let it run for 5 minutes BTC, then press and hold the reset button for 10seconds in order to restore to the default settings and reboot. The red LED will flash once every 15 seconds automatically if the reset is operated successfully.

Bitmain      11:37 AM (12 hours ago)
##- Please type your reply above this line -## Your request (2467) has been r...

Maybe they reply after 24hrs?

Cheers!
::*)

What router are you using? Noramly these things a have a web gui where you can see the devices connected with their IP addresses. Are you using Windows or any other OS to configure your miner?

[elrippo]

Now BITMAIN is offering an Fan Bracket with srews and the 6000rpm Fan for the SF-1 
What about the warranty if you remove the backside srews....

[notlist3d]

Now BITMAIN is offering an Fan Bracket with srews and the 6000rpm Fan for the SF-1 
What about the warranty if you remove the backside srews....

I personally like that they have started offering parts via website. They have made it where you can order many parts without shipping old ones in. This means you can have a spare on hand depending on how many you have this is a nice idea really.   

Could make it where you have 0 downtime almost if you have an extra part in some cases.   So I'm all for it personally on them selling parts to miners.

[elrippo]

I just received my S7-F1 & it will not produce an ip address to configure my miner. It seems to be hashing on the default pool settings Bitmain configures, more profit for them while customers configure or try to configure their miners. - The S7s do not have a specific ip address associated to the controller board. S7 user manual says:"Start ipreporter.exe, then press the IP Reporter button on IO board and you'll hear a beep sound" (When I press tge IP Reporter button on the IO board I never get a beep, MOFO just starts mining on Bitmain pools they have defaulted into the BIOS, reset does not erase the pool config data.

Following the instruction for the s7 pdf & downloading the Chinese version of ipreport the software always reports "has timed out start again" in Chinese, Gooble search translation.

I am sure the unit is mining because it goes full rpm on the fan & gives green LED on the controller board face. I do notice a red LED at rear closest to the ASIC boards, also red LED lights on the front of the ASIC boards. The unit produces heat, telling me it is mining somewhere.

There is a ‘Reset’ button on the right hand side of the Ethernet port, next to the green and red LED light. BTC Power on miner and let it run for 5 minutes BTC, then press and hold the reset button for 10seconds in order to restore to the default settings and reboot. The red LED will flash once every 15 seconds automatically if the reset is operated successfully.

Bitmain      11:37 AM (12 hours ago)
##- Please type your reply above this line -## Your request (2467) has been r...

Maybe they reply after 24hrs?

Cheers!
::*)

What router are you using? Normally these things a have a web gui where you can see the devices connected with their IP addresses. Are you using Windows or any other OS to configure your miner?

Thanks for the fast reply. I am using the ASUS RT-N12 D1 wireless router & it is set to use DHCP. I just hooked up an S1 to my network, it is mining on a pool & I am able to pull the ip address with advanced IP Scanner software showing me the ip address of the S1.

Cut cost here & there, I miss the sma input for wireless connectivity.

Oh my, why have the hashing deities forsaken me? ::*)

That's pretty easy.
Connect your PC and MINER via LAN to the router, login to your router and check the "Client Status". That should give you the IP of your miner and that's it -> http://www.dslregional.de/wp-content/uploads/asus-rt-n12-handbuch-bedienungsanleitung.pdf

That's pretty simple networking 

[elrippo]

Now BITMAIN is offering an Fan Bracket with srews and the 6000rpm Fan for the SF-1 
What about the warranty if you remove the backside srews....

I personally like that they have started offering parts via website. They have made it where you can order many parts without shipping old ones in. This means you can have a spare on hand depending on how many you have this is a nice idea really.   

Could make it where you have 0 downtime almost if you have an extra part in some cases.   So I'm all for it personally on them selling parts to miners.

Sure, i like getting spare parts easily and that's a great service, BUT if i remove the screws on the backside of the new B16 SF-1, i will brake the warranty if i do so in 90 days, so that is not what i want from BITMAIN...
They could offer a singel fan version and also an option for them to deliver the S7 with two fans, like they did actually.

[elrippo]

I just received my S7-F1 & it will not produce an ip address to configure my miner. It seems to be hashing on the default pool settings Bitmain configures, more profit for them while customers configure or try to configure their miners. - The S7s do not have a specific ip address associated to the controller board. S7 user manual says:"Start ipreporter.exe, then press the IP Reporter button on IO board and you'll hear a beep sound" (When I press tge IP Reporter button on the IO board I never get a beep, MOFO just starts mining on Bitmain pools they have defaulted into the BIOS, reset does not erase the pool config data.

Following the instruction for the s7 pdf & downloading the Chinese version of ipreport the software always reports "has timed out start again" in Chinese, Gooble search translation.

I am sure the unit is mining because it goes full rpm on the fan & gives green LED on the controller board face. I do notice a red LED at rear closest to the ASIC boards, also red LED lights on the front of the ASIC boards. The unit produces heat, telling me it is mining somewhere.

There is a ‘Reset’ button on the right hand side of the Ethernet port, next to the green and red LED light. BTC Power on miner and let it run for 5 minutes BTC, then press and hold the reset button for 10seconds in order to restore to the default settings and reboot. The red LED will flash once every 15 seconds automatically if the reset is operated successfully.

Bitmain      11:37 AM (12 hours ago)
##- Please type your reply above this line -## Your request (2467) has been r...

Maybe they reply after 24hrs?

Cheers!
::*)

What router are you using? Normally these things a have a web gui where you can see the devices connected with their IP addresses. Are you using Windows or any other OS to configure your miner?

Thanks for the fast reply. I am using the ASUS RT-N12 D1 wireless router & it is set to use DHCP. I just hooked up an S1 to my network, it is mining on a pool & I am able to pull the ip address with advanced IP Scanner software showing me the ip address of the S1.

Cut cost here & there, I miss the sma input for wireless connectivity.

Oh my, why have the hashing deities forsaken me? ::*)

That's pretty easy.
Connect your PC and MINER via LAN to the router, login to your router and check the "Client Status". That should give you the IP of your miner and that's it -> http://www.dslregional.de/wp-content/uploads/asus-rt-n12-handbuch-bedienungsanleitung.pdf

That's pretty simple networking 

I have hooked directly to the S7, the S7 will not generate an ip I can grab. I hook my old S1s up & poof they mine & are visible via the network I have.

Login to your router, attach the S7 via a lan cable to the routers LAN side, search for client status, make a screenshot and tell us what you see 

[smaxz]

I just received my S7-F1 & it will not produce an ip address to configure my miner. It seems to be hashing on the default pool settings Bitmain configures, more profit for them while customers configure or try to configure their miners.

Following the instruction for the s7 pdf & downloading the Chinese version of ipreport the software always reports "has timed out start again" in Chinese, Gooble search translation.

I am sure the unit is mining because it goes full rpm on the fan & gives green LED on the controller board face. I do notice a red LED at rear closest to the ASIC boards, also red LED lights on the front of the ASIC boards. The unit produces heat, telling me it is mining somewhere.

There is a ‘Reset’ button on the right hand side of the Ethernet port, next to the green and red LED light. BTC Power on miner and let it run for 5 minutes BTC, then press and hold the reset button for 10seconds in order to restore to the default settings and reboot. The red LED will flash once every 15 seconds automatically if the reset is operated successfully.

Bitmain      11:37 AM (12 hours ago)
##- Please type your reply above this line -## Your request (2467) has been r...

Maybe they reply after 24hrs?

Cheers!
::*)

are you on a /16 network? just try 192.168.0.2 through 192.168.0.25 or so in your browser.. this wont work obviously if you have a slew of devices on your network but if you just have a few tablets and laptops you can find the antminer within 5min by allowing each query to port 80 to timeout in your web browser till you hit the open port.

the fan actually turns down from full speed once it begins hashing.. if you have no boards plugged in but the fan connected to the control board, the fan still runs full power.

you can confirm this theory by checking the heat coming from the case.. it should be cold air if its not yet hashing.

i do like however how the default pools are solo mining pools so if an errand customer configure is lucky it hits a block for bitmain

[citronick]

I just received my S7-F1 & it will not produce an ip address to configure my miner. It seems to be hashing on the default pool settings Bitmain configures, more profit for them while customers configure or try to configure their miners.

Following the instruction for the s7 pdf & downloading the Chinese version of ipreport the software always reports "has timed out start again" in Chinese, Gooble search translation.

I am sure the unit is mining because it goes full rpm on the fan & gives green LED on the controller board face. I do notice a red LED at rear closest to the ASIC boards, also red LED lights on the front of the ASIC boards. The unit produces heat, telling me it is mining somewhere.

There is a ‘Reset’ button on the right hand side of the Ethernet port, next to the green and red LED light. BTC Power on miner and let it run for 5 minutes BTC, then press and hold the reset button for 10seconds in order to restore to the default settings and reboot. The red LED will flash once every 15 seconds automatically if the reset is operated successfully.

Bitmain      11:37 AM (12 hours ago)
##- Please type your reply above this line -## Your request (2467) has been r...

Maybe they reply after 24hrs?

Cheers!
::*)

what PSU are you using?
will a EVGA 1300w enough for this new S7-F1 ?

[smaxz]

specs are that you need 1250watts to run it. accounting for loss its likely over the specs of a evga 1300. taking the safety margin of never using more than 80% load for extended periods its for sure too much.

[Legacy2005]

Now BITMAIN is offering an Fan Bracket with srews and the 6000rpm Fan for the SF-1 
What about the warranty if you remove the backside srews....

hmm o look a way for them to get more money from us. they realize most will need the rear fan why not sell a unit with 1 and then charge more to get a second.

[notlist3d]

Now BITMAIN is offering an Fan Bracket with srews and the 6000rpm Fan for the SF-1 
What about the warranty if you remove the backside srews....
*removed pic so not huge post it is above

I personally like that they have started offering parts via website. They have made it where you can order many parts without shipping old ones in. This means you can have a spare on hand depending on how many you have this is a nice idea really.   

Could make it where you have 0 downtime almost if you have an extra part in some cases.   So I'm all for it personally on them selling parts to miners.

Sure, i like getting spare parts easily and that's a great service, BUT if i remove the screws on the backside of the new B16 SF-1, i will brake the warranty if i do so in 90 days, so that is not what i want from BITMAIN...
They could offer a singel fan version and also an option for them to deliver the S7 with two fans, like they did actually.

Sure but if in 90 day's you can email and get a anwser pretty quick getting permission and warranty remains in tact.  Shoot them a email and say my X part seems to be broken but I have a spare, can I replace it and see the results and keep warranty in tact?

Chances are a email as easy as that will keep your warranty in  tact if you did have a replacement part that needed changed in it.  So I don't see it as a huge thing, that will have a lot of downtime.

[carlosmnk]

I just received my S7-F1 & it will not produce an ip address to configure my miner. It seems to be hashing on the default pool settings Bitmain configures, more profit for them while customers configure or try to configure their miners.

Following the instruction for the s7 pdf & downloading the Chinese version of ipreport the software always reports "has timed out start again" in Chinese, Gooble search translation.

I am sure the unit is mining because it goes full rpm on the fan & gives green LED on the controller board face. I do notice a red LED at rear closest to the ASIC boards, also red LED lights on the front of the ASIC boards. The unit produces heat, telling me it is mining somewhere.

There is a ‘Reset’ button on the right hand side of the Ethernet port, next to the green and red LED light. BTC Power on miner and let it run for 5 minutes BTC, then press and hold the reset button for 10seconds in order to restore to the default settings and reboot. The red LED will flash once every 15 seconds automatically if the reset is operated successfully.

Bitmain      11:37 AM (12 hours ago)
##- Please type your reply above this line -## Your request (2467) has been r...

Maybe they reply after 24hrs?

Cheers!
::*)

what PSU are you using?
will a EVGA 1300w enough for this new S7-F1 ?

Probably not, usually, this miners are draining 1400w (perphaps more), so, it is not enough... 

[Sierra8561]

Does anyone have any extra bitmain $100.00 off coupons they would donate me?

[mu77aL]

Does anyone have any extra bitmain $100.00 off coupons they would donate me?

Haha - I would take that aswell
Anyways could you guys give a little review of the Profibility of the Antminer s7 ?
That would be awesome to know which profits you guys generating with theese.

regards

[aarons6]

Does anyone have any extra bitmain $100.00 off coupons they would donate me?

Haha - I would take that aswell
Anyways could you guys give a little review of the Profibility of the Antminer s7 ?
That would be awesome to know which profits you guys generating with theese.

regards

profitability is 100% subject to power costs and the type of power supply you choose.  there is no way to suggest you will be profitable or not without knowing what yours is.

[alh]

Does anyone have any extra bitmain $100.00 off coupons they would donate me?

Haha - I would take that aswell
Anyways could you guys give a little review of the Profibility of the Antminer s7 ?
That would be awesome to know which profits you guys generating with theese.

regards

As always, start with something like:

https://bitcoinwisdom.com/bitcoin/difficulty

At the present BTC price and zero cost electricity, an S7 will earn about $40 for the next week. You can do the math to figure out how long it will take to pay off your S7. Don't forget cooling, and PSU cost in your calculation.

As was mentioned, it all comes down to ELECTRICITY, ELECTRICITY, ELECTRICITY!!!

[elrippo]

Does anyone have any extra bitmain $100.00 off coupons they would donate me?

Haha - I would take that aswell
Anyways could you guys give a little review of the Profibility of the Antminer s7 ?
That would be awesome to know which profits you guys generating with theese.

regards

As always, start with something like:

https://bitcoinwisdom.com/bitcoin/difficulty

At the present BTC price and zero cost electricity, an S7 will earn about $40 for the next week. You can do the math to figure out how long it will take to pay off your S7. Don't forget cooling, and PSU cost in your calculation.

As was mentioned, it all comes down to ELECTRICITY, ELECTRICITY, ELECTRICITY!!!

I personally prefer this one to play with some calculations -> https://tradeblock.com/bitcoin/mining

[SaBit]

If you know the MAC address, bind it to a static ip, then you can acces the gui?

I just received my S7-F1 & it will not produce an ip address to configure my miner. It seems to be hashing on the default pool settings Bitmain configures, more profit for them while customers configure or try to configure their miners.

Following the instruction for the s7 pdf & downloading the Chinese version of ipreport the software always reports "has timed out start again" in Chinese, Gooble search translation.

I am sure the unit is mining because it goes full rpm on the fan & gives green LED on the controller board face. I do notice a red LED at rear closest to the ASIC boards, also red LED lights on the front of the ASIC boards. The unit produces heat, telling me it is mining somewhere.

There is a ‘Reset’ button on the right hand side of the Ethernet port, next to the green and red LED light. BTC Power on miner and let it run for 5 minutes BTC, then press and hold the reset button for 10seconds in order to restore to the default settings and reboot. The red LED will flash once every 15 seconds automatically if the reset is operated



Maybe they reply after 24hrs?

Cheers!
::*)

are you on a /16 network? just try 192.168.0.2 through 192.168.0.25 or so in your browser.. this wont work obviously if you have a slew of devices on your network but if you just have a few tablets and laptops you can find the antminer within 5min by allowing each query to port 80 to timeout in your web browser till you hit the open port.

the fan actually turns down from full speed once it begins hashing.. if you have no boards plugged in but the fan connected to the control board, the fan still runs full power.

you can confirm this theory by checking the heat coming from the case.. it should be cold air if its not yet hashing.

i do like however how the default pools are solo mining pools so if an errand customer configure is lucky it hits a block for bitmain

[elrippo]

If you know the MAC address, bind it to a static ip, then you can acces the gui?

I just received my S7-F1 & it will not produce an ip address to configure my miner. It seems to be hashing on the default pool settings Bitmain configures, more profit for them while customers configure or try to configure their miners.

Following the instruction for the s7 pdf & downloading the Chinese version of ipreport the software always reports "has timed out start again" in Chinese, Gooble search translation.

I am sure the unit is mining because it goes full rpm on the fan & gives green LED on the controller board face. I do notice a red LED at rear closest to the ASIC boards, also red LED lights on the front of the ASIC boards. The unit produces heat, telling me it is mining somewhere.

There is a ‘Reset’ button on the right hand side of the Ethernet port, next to the green and red LED light. BTC Power on miner and let it run for 5 minutes BTC, then press and hold the reset button for 10seconds in order to restore to the default settings and reboot. The red LED will flash once every 15 seconds automatically if the reset is operated



Maybe they reply after 24hrs?

Cheers!
::*)

are you on a /16 network? just try 192.168.0.2 through 192.168.0.25 or so in your browser.. this wont work obviously if you have a slew of devices on your network but if you just have a few tablets and laptops you can find the antminer within 5min by allowing each query to port 80 to timeout in your web browser till you hit the open port.

the fan actually turns down from full speed once it begins hashing.. if you have no boards plugged in but the fan connected to the control board, the fan still runs full power.

you can confirm this theory by checking the heat coming from the case.. it should be cold air if its not yet hashing.

i do like however how the default pools are solo mining pools so if an errand customer configure is lucky it hits a block for bitmain

That would be a way for example