SgtSpike
Legendary
Offline
Activity: 1400
Merit: 1005
|
|
November 06, 2012, 11:31:25 PM |
|
I guessed right, 65nm, big surprise? The disturbing thing is they are using Full Custom ASIC, at 65nm process node, at 60watts. (@60GH/s) The competitor (bASIC) is using structured ASIC I believe and is below the 100watt mark on a 90nm process node. (@54GH/s) Some leaked pictures show that it might be at around 58 to 60watts. But the caption was removed so it is hard to figure out if true or not. Either way, for a smaller process node...not as efficient as it should be. Perhaps I am missing something....? I know that 60 watts is an estimated and conservative figure.
|
|
|
|
MrTeal
Legendary
Offline
Activity: 1274
Merit: 1004
|
|
November 06, 2012, 11:53:14 PM |
|
I guessed right, 65nm, big surprise? The disturbing thing is they are using Full Custom ASIC, at 65nm process node, at 60watts. (@60GH/s) The competitor (bASIC) is using structured ASIC I believe and is below the 100watt mark on a 90nm process node. (@54GH/s) Some leaked pictures show that it might be at around 58 to 60watts. But the caption was removed so it is hard to figure out if true or not. Either way, for a smaller process node...not as efficient as it should be. Perhaps I am missing something....? When did Tom say that they were using a structured ASIC?
|
|
|
|
ElectricMucus
Legendary
Offline
Activity: 1666
Merit: 1057
Marketing manager - GO MP
|
|
November 07, 2012, 12:17:28 AM |
|
Altera Hardcopy is "65nm" too.
Of course they won't admit that they are using it.
|
|
|
|
SgtSpike
Legendary
Offline
Activity: 1400
Merit: 1005
|
|
November 07, 2012, 12:27:24 AM |
|
Altera Hardcopy is "65nm" too.
Of course they won't admit that they are using it.
You're saying they are lying about creating a full custom ASIC?
|
|
|
|
ElectricMucus
Legendary
Offline
Activity: 1666
Merit: 1057
Marketing manager - GO MP
|
|
November 07, 2012, 12:41:22 AM |
|
Altera Hardcopy is "65nm" too.
Of course they won't admit that they are using it.
You're saying they are lying about creating a full custom ASIC? Yes
|
|
|
|
2GOOD
|
|
November 07, 2012, 12:49:20 AM |
|
Altera Hardcopy is "65nm" too.
Of course they won't admit that they are using it.
I don't see 65nm on the product page: http://goo.gl/LhjH7
|
|
|
|
ElectricMucus
Legendary
Offline
Activity: 1666
Merit: 1057
Marketing manager - GO MP
|
|
November 07, 2012, 12:51:58 AM |
|
Altera Hardcopy is "65nm" too.
Of course they won't admit that they are using it.
I don't see 65nm on the product page: http://goo.gl/LhjH7Ok they probably are not using Altera Hardcopy. Perhaps Xilinx Easypath? You see there are several companies who off fpga conversion "ASICs", I don't know them all.
|
|
|
|
MrTeal
Legendary
Offline
Activity: 1274
Merit: 1004
|
|
November 07, 2012, 01:02:22 AM |
|
Altera Hardcopy is "65nm" too.
Of course they won't admit that they are using it.
I don't see 65nm on the product page: http://goo.gl/LhjH7Ok they probably are not using Altera Hardcopy. Perhaps Xilinx Easypath? You see there are several companies who off fpga conversion "ASICs", I don't know them all. Could you point us to which Hardcopy family members use a 68 pin 11mmx11mm QFN? http://www.altera.com/devices/asic/hardcopy-asics/about/hrd-index.html
|
|
|
|
kjlimo
Legendary
Offline
Activity: 2114
Merit: 1031
|
|
November 07, 2012, 01:45:06 AM |
|
So is the lower the nm, the better?
so if someone came out with 20nm, that would be faster or use electricity than a 45nm chip?
|
|
|
|
SgtSpike
Legendary
Offline
Activity: 1400
Merit: 1005
|
|
November 07, 2012, 02:16:24 AM |
|
So is the lower the nm, the better?
so if someone came out with 20nm, that would be faster or use electricity than a 45nm chip?
Probably both.
|
|
|
|
mrb
Legendary
Offline
Activity: 1512
Merit: 1027
|
|
November 07, 2012, 05:09:12 AM |
|
Altera Hardcopy is "65nm" too.
Of course they won't admit that they are using it.
I don't see 65nm on the product page: http://goo.gl/LhjH7Ok they probably are not using Altera Hardcopy. Perhaps Xilinx Easypath? You see there are several companies who off fpga conversion "ASICs", I don't know them all. You are wrong again, ElectricMucus. The few times I have made predictions(*) against "mainstream thoughts" in the Bitcoin world, I have always been right, and I will tell you: I predict SC is not based on a FPGA-to-ASIC chip. (*) Just a few examples: I correctly estimated HD 7000's MHash per Joule before release, from theoretical computations based on its known process node. I correctly predicted pirateat40 was running a Ponzi when many refused to believe. I correctly predicted 65nm for the SC lineup. And I seem to be on a path to win my SC mining efficiency bet when people where ignorant enough to bet 50 BTC against me. ^ Prepare yourself to be appended to this list in the near future. I have the track record to justify my confidence
|
|
|
|
punin (OP)
|
|
November 07, 2012, 08:22:12 AM |
|
I guessed right, 65nm, big surprise? The disturbing thing is they are using Full Custom ASIC, at 65nm process node, at 60watts. (@60GH/s) The competitor (bASIC) is using structured ASIC I believe and is below the 100watt mark on a 90nm process node. (@54GH/s) Some leaked pictures show that it might be at around 58 to 60watts. But the caption was removed so it is hard to figure out if true or not. Either way, for a smaller process node...not as efficient as it should be. Perhaps I am missing something....? The toggle-rate is so high that they are running the chips with much lower frequency that you would normally expect to run 65nm designs on to protect them from overheating. Had they gone with other package (eg. flip-chip), they could've run them at much higher clocks. What leaked pictures are you referring to? URL?
|
|
|
|
BFL-Engineer
|
|
November 07, 2012, 10:17:20 AM |
|
Regarding the chip being hardcopy or easypath or any other structured ASIC, please be advised that none of those chips come in small packages. They are all 480pin or above (BGA chips), not QFN. The reason behind it is that most industries going after hardcopy or easypth are the ones using the high IO count FPGA version of those chips (which are very expensive for a mass-produced product).
I hope this clarifies the situation.
Regards, BFL-Engineer
|
|
|
|
2GOOD
|
|
November 07, 2012, 11:04:02 PM |
|
Better later than never WE just have to wait and see.
|
|
|
|
BR0KK
|
|
November 07, 2012, 11:14:33 PM |
|
My issue came yesterday Read the article and now i'm thrilled to see an actual Product out and hashing! If that happens i might consider buying one or two singles SC; or even more! (i won't preorder ..... that is not about to change since i don't like that "tactics" of bfl. Maybe if you had called it community funding with preorder guarantee back then, i would have..... )
|
|
|
|
Bogart
Legendary
Offline
Activity: 966
Merit: 1000
|
|
November 08, 2012, 06:11:06 AM |
|
The toggle-rate is so high that they are running the chips with much lower frequency that you would normally expect to run 65nm designs on to protect them from overheating. Had they gone with other package (eg. flip-chip), they could've run them at much higher clocks.
Can the chip package be changed to a more thermally efficient design in a subsequent production run of chips without having to make a new mask, and incur a whole new set or NRE costs?
|
"All safe deposit boxes in banks or financial institutions have been sealed... and may only be opened in the presence of an agent of the I.R.S." - President F.D. Roosevelt, 1933
|
|
|
ChipGeek
|
|
November 08, 2012, 06:23:01 AM |
|
The toggle-rate is so high that they are running the chips with much lower frequency that you would normally expect to run 65nm designs on to protect them from overheating. Had they gone with other package (eg. flip-chip), they could've run them at much higher clocks.
Can the chip package be changed to a more thermally efficient design in a subsequent production run of chips without having to make a new mask, and incur a whole new set or NRE costs? This is an excellent question. Here's my educated guess for an answer: It is likely that a new mask would need to be made for the top layer at a minimum. Edit: Yes flip-chip would be a much better thermal design. We do flip-chip for our custom chips.
|
Tip jar: 1ChipGeeK7PDxaAWG4VgsTi31SfJ6peKHw
|
|
|
SLok
|
|
November 08, 2012, 08:16:28 PM Last edit: November 09, 2012, 12:16:08 AM by Maged |
|
In the article is mentioned that these chips can in theory, run up to 16Gh/s max., but will not live long if pumped up to this. What is needed to overclock these single SC's chips to maybe 10-12Gh/s a piece, so a single would do 80-96Gh/s? Just the right mining software, or is a modded firmware needed?
|
WARNING! Don't trade BTC with Bruno Kucinskas aka Gleb Gamow, Phinnaeus Gage, etc Laundering BTC from anonymous sellers, avoid! https://bitcointalk.org/index.php?topic=649176.msg7279994#msg7279994 #TELLFBI #TELLKSAG #TELLIRS WARNING! Darin M. Bicknell, a proclaimed atheist, teaching at the Jakarta CanadianMontessori School. Drop your kids there at your own risk! WARNING! Christian Otzipka - Hildesheim is a known group-buy scammer, avoid! WARNING! Frizz Supertramp, faker with dozens of accounts here! WARNING! Christian "2 coins to see SLOk's" Antkow, still playing his little microphone... WARNING! Slobodan "Stolen Valor" Bogovac, faking being a Professor WARNING!Marion Sydney Lynn, google him, errr her, errr.. and lol
|
|
|
SgtSpike
Legendary
Offline
Activity: 1400
Merit: 1005
|
|
November 08, 2012, 08:18:13 PM |
|
Well, they have the waterblock heatsink that could be used. I bet that'd get some nice overclockz going.
|
|
|
|
bitboyben
|
|
November 21, 2012, 05:05:07 AM |
|
The article definately alludes to the chips running 50% theoretical I would guess another 50% (80-90Ghash for SC) would be safe with the right cooling set up. It doesn't really excite me as much as it used to because, hey everyone else is going to do it too.
|
Why did I sell at $5! Come back to me my old bitcoin! 1GjeBGS4KrxKAeEVt8d1fTnuKgpKpMmL6S If you don't like the price of BTC come back in 8 hours.
|
|
|
|