toomeke
Newbie
 Offline
Activity: 49
Merit: 0
|
 |
July 28, 2017, 08:58:05 AM |
|
What are the hash rates for the GTX 1060 for SIG/skunkhash?
Looking to start up some miners on this but need to know so I can estimate the rewards.
Currently runs at 18mh/s @ 70 TDP 64C 6GB Version, 3GB runs @ 16mh/s. 18? damm thats good Im squeezing 13.5mh from my 1060's, what OC settings and intensity? share the love bruv! |
|
|
|
|
|
|
|
|
|
"I'm sure that in 20 years there will either be very large transaction volume or no volume." -- Satoshi
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
ishem
Member
Offline
Activity: 112
Merit: 10
|
|
July 28, 2017, 08:59:36 AM |
|
I'm mining on suprnova, not getting the estimate as on whattomine. I think the reasons could be the fluctuating difficulty - I see it go up to 19000 and then drop to 10000 all the time, so number you see at whattomine is probably a very rough estimate. There are also other problems - for some reason my miner misfires from time to time, job not found, share doesn't validate and so on - not sure why this happens, maybe problems with bandwidth or else. All of this contributes to lower profit. Hopefully they'll work to minimize these problems. I think neither pool is perfect at the moment,
|
|
|
|
|
brizio71
Sr. Member
Offline
Activity: 456
Merit: 250
Blockchain Just Entered The Real World
|
|
July 28, 2017, 09:00:31 AM |
|
Which is the best miner for RX GPU ?
|
|
|
|
nizzuu
Full Member
Offline
Activity: 187
Merit: 100
Cryptocurrency enthusiast
|
|
July 28, 2017, 09:10:48 AM |
|
please help sgminer cant run at rx 560
Step 1: verify your device is present for miner sgminer -n
pauseStep 2: run the miner, set -g number to your device number(s). If you have Intel HD graphics and it's enabled, try --gpu-platform 0 as well.
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_MAX_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_MAX_SINGLE_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
sgminer.exe -k skunkhash -o stratum+tcp://yiimp.ccminer.org:8433 -u qwerty -p c=SIGT -I 16 -w 128 -g 0 --gpu-platform 1
This works fine for RX460 4Gb which is technically almost the same as RX560. |
|
|
|
|
|
Propagandalf
|
|
July 28, 2017, 09:14:28 AM |
|
Question -
I have been thinking of stepping up to 'community leader' position in this coin. Basically being the face of the project for the world. So that people know there is a real person behind it.
Of course, this also includes me using my contacts to help with all aspects of the project, and of course I myself helping, like I did with cryptopia getting listed there.
I would like to do this for everyone here, if that's alright with everyone.
Any questions feel free to ask, nothing to hide here.
I work full-time crypto, so I would have the time along with the contacts, to help further things along for SIGT. I very much enjoy helping solid projects, getting new people involved, and just giving and helping in general. So this would be quite fun for me.
Just wanted to post here and let everyone know what I was thinking, and make sure everyone would be fine with that before just giving myself the title.
I work closely with SIGT current devs, and have others that are working on SIGT things as well.
Let me know if you're all okay with this, and if not, why?
If anyone has any legitimate concerns, we can definitely talk about it, but I can say for certain that I'll do everything I can to help things get where they should go.
Thanks!
I'm good with that!  |
|
|
|
|
|
|
|
Slava_K
|
|
July 28, 2017, 09:24:33 AM |
|
No, I bought ccminer sp_mode v3 and use. I dont download this strange software anyway. Only compiled by miself ore bought from trustet developers. |
|
|
|
|
car1999
|
|
July 28, 2017, 09:29:16 AM |
|
I'm mining on suprnova, not getting the estimate as on whattomine. I think the reasons could be the fluctuating difficulty - I see it go up to 19000 and then drop to 10000 all the time, so number you see at whattomine is probably a very rough estimate. There are also other problems - for some reason my miner misfires from time to time, job not found, share doesn't validate and so on - not sure why this happens, maybe problems with bandwidth or else. All of this contributes to lower profit. Hopefully they'll work to minimize these problems. I think neither pool is perfect at the moment,
thanks, I'll try to mine on yiimp.ccminer.org 24 hours and check the result. |
|
|
|
|
BloodViolet
Newbie
Offline
Activity: 3
Merit: 0
|
|
July 28, 2017, 09:42:24 AM |
|
Looks promising. Just bought a few and looking forward to the future of this project.
Is mining still worth it for small miners?
|
|
|
|
|
toomeke
Newbie
Offline
Activity: 49
Merit: 0
|
|
July 28, 2017, 09:43:04 AM |
|
Wouldnt touch non legit revisions |
|
|
|
|
Bierbam
Newbie
Offline
Activity: 36
Merit: 0
|
|
July 28, 2017, 09:45:49 AM |
|
Can only say that it works, Don't know if it's altered in any way as I don't have the original source nor binary that could be told by the others^^ Miner says 11.02(73W) and 11.42Mhs(74W), for each GTX1050Ti, pool is also climbing up to 21Mhs, but I had rejects dropping it to ~16Mhs, would need some hours for an average. And then the same test with 50W ^^ And then a good wipe |
|
|
|
|
ishem
Member
Offline
Activity: 112
Merit: 10
|
|
July 28, 2017, 09:49:50 AM |
|
No, I bought ccminer sp_mode v3 and use. I dont download this strange software anyway. Only compiled by miself ore bought from trustet developers. Is your filesize exactly the same as this executable? Easy to check. |
|
|
|
|
|
xyburcoin
|
|
July 28, 2017, 09:56:16 AM |
|
This is actually quite a good miner... kudos to you! |
Life is ours, we live it our way.
|
|
|
ralt
Member
Offline
Activity: 132
Merit: 10
|
|
July 28, 2017, 10:07:07 AM |
|
Hi!
15.60 MH/s with a GTX 1070 is OK?
Thanks a lot!!
I think 1070 should give you 20~25 MH/s It is 25 MH/s now with the new miner posted here. Thanks a lot! |
|
|
|
babuubabuu
Newbie
Offline
Activity: 15
Merit: 0
|
|
July 28, 2017, 10:11:49 AM |
|
Unfortunately not working here : *** ccminer alexis-1.0 palgin skunkmod for nVidia GPUs from alexis78@github *** *** Built with the nVidia CUDA Toolkit 8.0 (Not recommended prefer 7.5) *** Based on tpruvot@github ccminer *** Originally based on Christian Buchner and Christian H. project *** Include some of the work of djm34, sp, tsiv and klausT. *** Skunk algo modded by palgin Illegal instruction I experience this too. Any solution? As I posted earlier: Workaround for Ubuntu bins and their errors: 1) sudo apt install nvidia-cuda-toolkit 2) sudo apt install libcurl4-openssl-dev 3) sudo apt install libssl-dev 4) if it keeps thowing errors about CUDA libs, run "sudo ldconfig /your/cuda/libs/path" , 32-bit versions 5) Reboot if you want Try installing CUDA 8 toolkit, error shows that instructions used during kernel launch are unsupported in your version of CUDA. Please, check and reply, I've specially installed Ubuntu on several hosts and tested, after manipulations I've mentioned earlier everything worked fine. ccminer-ccminer.o: In function `miner_thread(void*)':
ccminer.cpp:(.text+0x7b75): undefined reference to `scanhash_timetravel10'
ccminer-util.o: In function `print_hash_tests':
util.cpp:(.text+0x7a29): undefined reference to `timetravel10_hash'
ccminer-bench.o: In function `algo_free_all':
bench.cpp:(.text+0x215): undefined reference to `free_timetravel10'
collect2: error: ld returned 1 exit status
Makefile:1130: recipe for target 'ccminer' failed
make[2]: *** [ccminer] Error 1
make[2]: Leaving directory '/home/babuubabuu/ccminer-skunk-1'
Makefile:2115: recipe for target 'all-recursive' failed
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory '/home/babuubabuu/ccminer-skunk-1'
Makefile:633: recipe for target 'all' failed
make: *** [all] Error 2
I did install cuda toolkit & Openssl & libcurl4 My system can run tpruvot version fine but can't run build.sh from palginpav version. This is the error code before build.sh terminate itself. |
|
|
|
|
|
palgin
|
|
July 28, 2017, 10:20:58 AM |
|
Unfortunately not working here : *** ccminer alexis-1.0 palgin skunkmod for nVidia GPUs from alexis78@github *** *** Built with the nVidia CUDA Toolkit 8.0 (Not recommended prefer 7.5) *** Based on tpruvot@github ccminer *** Originally based on Christian Buchner and Christian H. project *** Include some of the work of djm34, sp, tsiv and klausT. *** Skunk algo modded by palgin Illegal instruction I experience this too. Any solution? As I posted earlier: Workaround for Ubuntu bins and their errors: 1) sudo apt install nvidia-cuda-toolkit 2) sudo apt install libcurl4-openssl-dev 3) sudo apt install libssl-dev 4) if it keeps thowing errors about CUDA libs, run "sudo ldconfig /your/cuda/libs/path" , 32-bit versions 5) Reboot if you want Try installing CUDA 8 toolkit, error shows that instructions used during kernel launch are unsupported in your version of CUDA. Please, check and reply, I've specially installed Ubuntu on several hosts and tested, after manipulations I've mentioned earlier everything worked fine. ccminer-ccminer.o: In function `miner_thread(void*)':
ccminer.cpp:(.text+0x7b75): undefined reference to `scanhash_timetravel10'
ccminer-util.o: In function `print_hash_tests':
util.cpp:(.text+0x7a29): undefined reference to `timetravel10_hash'
ccminer-bench.o: In function `algo_free_all':
bench.cpp:(.text+0x215): undefined reference to `free_timetravel10'
collect2: error: ld returned 1 exit status
Makefile:1130: recipe for target 'ccminer' failed
make[2]: *** [ccminer] Error 1
make[2]: Leaving directory '/home/babuubabuu/ccminer-skunk-1'
Makefile:2115: recipe for target 'all-recursive' failed
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory '/home/babuubabuu/ccminer-skunk-1'
Makefile:633: recipe for target 'all' failed
make: *** [all] Error 2
I did install cuda toolkit & Openssl & libcurl4 My system can run tpruvot version fine but can't run build.sh from palginpav version. This is the error code before build.sh terminate itself. Simple, source isn't included, you won't be able to build it, only use bins released. UPD: https://github.com/palginpav/ccminer/releases/download/v1.1/ccminer-1.1-skunk.zip , with reworked algos, speedup for 10xx cards, haven't tested on 9xx |
BTC tips welcome: 16DHzyuqenEoHRA3w3YVGcYSDSHks7mor4
|
|
|
nizzuu
Full Member
Offline
Activity: 187
Merit: 100
Cryptocurrency enthusiast
|
|
July 28, 2017, 10:36:56 AM |
|
UPD: ccminer-1.1-skunk.zip, with reworked algos, speedup for 10xx cards, haven't tested on 9xx
Wow wow, 50Mh/s on 1080ti with -i 24.5 And 8750kH/s on 1050s with -i 23.5. Thanks, bro, you're cool. |
|
|
|
|
|
MarcusDe
|
|
July 28, 2017, 10:47:39 AM |
|
This is actually quite a good miner... kudos to you! Thanks for leaked sp3 mate :-) |
|
|
|
shikhov
Newbie
Offline
Activity: 34
Merit: 0
|
|
July 28, 2017, 10:49:58 AM |
|
Unfortunately not working here : *** ccminer alexis-1.0 palgin skunkmod for nVidia GPUs from alexis78@github *** *** Built with the nVidia CUDA Toolkit 8.0 (Not recommended prefer 7.5) *** Based on tpruvot@github ccminer *** Originally based on Christian Buchner and Christian H. project *** Include some of the work of djm34, sp, tsiv and klausT. *** Skunk algo modded by palgin Illegal instruction I experience this too. Any solution? As I posted earlier: Workaround for Ubuntu bins and their errors: 1) sudo apt install nvidia-cuda-toolkit 2) sudo apt install libcurl4-openssl-dev 3) sudo apt install libssl-dev 4) if it keeps thowing errors about CUDA libs, run "sudo ldconfig /your/cuda/libs/path" , 32-bit versions 5) Reboot if you want Try installing CUDA 8 toolkit, error shows that instructions used during kernel launch are unsupported in your version of CUDA. Please, check and reply, I've specially installed Ubuntu on several hosts and tested, after manipulations I've mentioned earlier everything worked fine. ccminer-ccminer.o: In function `miner_thread(void*)':
ccminer.cpp:(.text+0x7b75): undefined reference to `scanhash_timetravel10'
ccminer-util.o: In function `print_hash_tests':
util.cpp:(.text+0x7a29): undefined reference to `timetravel10_hash'
ccminer-bench.o: In function `algo_free_all':
bench.cpp:(.text+0x215): undefined reference to `free_timetravel10'
collect2: error: ld returned 1 exit status
Makefile:1130: recipe for target 'ccminer' failed
make[2]: *** [ccminer] Error 1
make[2]: Leaving directory '/home/babuubabuu/ccminer-skunk-1'
Makefile:2115: recipe for target 'all-recursive' failed
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory '/home/babuubabuu/ccminer-skunk-1'
Makefile:633: recipe for target 'all' failed
make: *** [all] Error 2
I did install cuda toolkit & Openssl & libcurl4 My system can run tpruvot version fine but can't run build.sh from palginpav version. This is the error code before build.sh terminate itself. Simple, source isn't included, you won't be able to build it, only use bins released. UPD: https://github.com/palginpav/ccminer/releases/download/v1.1/ccminer-1.1-skunk.zip , with reworked algos, speedup for 10xx cards, haven't tested on 9xx 51.8 Mh 1080ti i 22 Thank you |
|
|
|
|
|
car1999
|
|
July 28, 2017, 11:00:21 AM |
|
Unfortunately not working here : *** ccminer alexis-1.0 palgin skunkmod for nVidia GPUs from alexis78@github *** *** Built with the nVidia CUDA Toolkit 8.0 (Not recommended prefer 7.5) *** Based on tpruvot@github ccminer *** Originally based on Christian Buchner and Christian H. project *** Include some of the work of djm34, sp, tsiv and klausT. *** Skunk algo modded by palgin Illegal instruction I experience this too. Any solution? As I posted earlier: Workaround for Ubuntu bins and their errors: 1) sudo apt install nvidia-cuda-toolkit 2) sudo apt install libcurl4-openssl-dev 3) sudo apt install libssl-dev 4) if it keeps thowing errors about CUDA libs, run "sudo ldconfig /your/cuda/libs/path" , 32-bit versions 5) Reboot if you want Try installing CUDA 8 toolkit, error shows that instructions used during kernel launch are unsupported in your version of CUDA. Please, check and reply, I've specially installed Ubuntu on several hosts and tested, after manipulations I've mentioned earlier everything worked fine. ccminer-ccminer.o: In function `miner_thread(void*)':
ccminer.cpp:(.text+0x7b75): undefined reference to `scanhash_timetravel10'
ccminer-util.o: In function `print_hash_tests':
util.cpp:(.text+0x7a29): undefined reference to `timetravel10_hash'
ccminer-bench.o: In function `algo_free_all':
bench.cpp:(.text+0x215): undefined reference to `free_timetravel10'
collect2: error: ld returned 1 exit status
Makefile:1130: recipe for target 'ccminer' failed
make[2]: *** [ccminer] Error 1
make[2]: Leaving directory '/home/babuubabuu/ccminer-skunk-1'
Makefile:2115: recipe for target 'all-recursive' failed
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory '/home/babuubabuu/ccminer-skunk-1'
Makefile:633: recipe for target 'all' failed
make: *** [all] Error 2
I did install cuda toolkit & Openssl & libcurl4 My system can run tpruvot version fine but can't run build.sh from palginpav version. This is the error code before build.sh terminate itself. Simple, source isn't included, you won't be able to build it, only use bins released. UPD: https://github.com/palginpav/ccminer/releases/download/v1.1/ccminer-1.1-skunk.zip , with reworked algos, speedup for 10xx cards, haven't tested on 9xx no linux version? |
|
|
|
|
|
