hsrminer - Nvidia mining software for various algos by palgin&alexkap

[Elder III]

I switched to Zpool.ca and have mined for 30 minutes without any rejected shares or disconnects. On altminer.net I would have had several rejects in that amount of time.

[1715438338]

1715438338

[1715438338]

1715438338

[NetopyrMan]

wierd thing just happent to 1 of my 1070ti rig ... miner just stopped ... no connection error, no other error, no crash, window still opened ... last line was Share accepted ...

[natan069]

I switched to Zpool.ca and have mined for 30 minutes without any rejected shares or disconnects. On altminer.net I would have had several rejects in that amount of time.

altminer seems like it got too big!
Getting less and less blocks there, stoped using for some days, don´t knw what happens

[reflexmk]

Is there a working CUDA 9 driver for p106-100 cards?

[fuda]

wierd thing just happent to 1 of my 1070ti rig ... miner just stopped ... no connection error, no other error, no crash, window still opened ... last line was Share accepted ...

Have you tried pressing Enter in command line after this happened?
I experienced same issue with ccminer.

After pressing Enter, there were couple of rejected shares and the miner proceeded.
Although it seems that the connection to pool wasn't broken (checked via currports/wireshark).

Maybe this could be solved by adding simple condition in the code...

[NetopyrMan]

wierd thing just happent to 1 of my 1070ti rig ... miner just stopped ... no connection error, no other error, no crash, window still opened ... last line was Share accepted ...

Have you tried pressing Enter in command line after this happened?
I experienced same issue with ccminer.

i tried another things that works same (like right click) but no change this happened on my 1st rig sometimes but for long time it didnt did that

[aik6]

Hi Dev, i use your mining software for about > 4 days till now

just want give litte info, hope will be useful for development process

sometimes the miner just idle, no error or anything else, i already experience this 2 times until now,
for my rig its happen when miner switch back to original coin after dev fee mining

thank you for your hard work

[NetopyrMan]

realy wierd ...
test version, no -i

sometimes miner stops ... resp. gpu dont do their job .. power consumption is on 15w per card ... but it takes only about couple of secs (under 30) and then continue with work

[spider703]

Hi Dev, i use your mining software for about > 4 days till now

just want give litte info, hope will be useful for development process

sometimes the miner just idle, no error or anything else, i already experience this 2 times until now,
for my rig its happen when miner switch back to original coin after dev fee mining

thank you for your hard work

this my bat file

:start
hsrminer -a hsr -o stratum+tcp://hsr.mine.zpool.ca:7433 -u 1J6ERS9LjhRhXkifkVfdpbP56aY7TLqEoe -p home
goto start

even if the miner suddenly stops, he restarts himself

[car1999]

I've run the neoscrypt test version 24 hours on 6x1080ti and get 10mh/s, very stable, thanks dev.

[NetopyrMan]

Only on 1080ti (test version, no -i, tdp100, core+107, mem+350)

Cuda error in func 'neoscrypt_cpu_hash_1080' at line 1509 : unspecified launch failure.

[spider703]

Only on 1080ti (test version, no -i, tdp100, core+107, mem+350)

Cuda error in func 'neoscrypt_cpu_hash_1080' at line 1509 : unspecified launch failure.

overclock, try to TDP +90 core +100 mem +250

[NetopyrMan]

Only on 1080ti (test version, no -i, tdp100, core+107, mem+350)

Cuda error in func 'neoscrypt_cpu_hash_1080' at line 1509 : unspecified launch failure.

overclock, try to TDP +90 core +100 mem +250

wierd, now tdp100, core +125, mem +400 and no crash ... 2015kH

[stivensons]

Only on 1080ti (test version, no -i, tdp100, core+107, mem+350)

Cuda error in func 'neoscrypt_cpu_hash_1080' at line 1509 : unspecified launch failure.

overclock, try to TDP +90 core +100 mem +250

wierd, now tdp100, core +125, mem +400 and no crash ... 2015kH

what card manufacturer?

[NetopyrMan]

evga ftw3 version

[melpheos]

In a quick test with test neoscrypt version with -i 17.8 on a 1070 i go from 1037mh/s to 1095mh/s so the 1% dev fee i well deserved
I'll put it on my two 6*1070ti and check the results but that's a net 4.5% increase in hashrate  

edit: on my two rigs i go from 8025 to 8325 so if you remove the dev fee i'm at 8240 so that's a 2.6% net increase. Not as good as with my 1070 but still a very nice improvement over ccminer 818

[NetopyrMan]

In a quick test with test neoscrypt version with -i 17.8 on a 1070 i go from 1037mh/s to 1095mh/s so the 1% dev fee i well deserved
I'll put it on my two 6*1070ti and check the results but that's a net 4.5% increase in hashrate  

edit: on my two rigs i go from 8025 to 8325 so if you remove the dev fee i'm at 8240 so that's a 2.6% net increase. Not as good as with my 1070 but still a very nice improvement over ccminer 818

i have on my 1070s about 1140+-MH (95tdp, +107core, +350mem) and if there is -i option, then 4 ... how can you have there 17.8 :-D everything over 5 was crash to my gpus (1080ti inc.)

[NetopyrMan]

i have a question about -i setting

i have two gtx 1060 6g with ccminer i run about 1275 khs very stable, with hsrminer about 1350 khs but crash a lot so do i need to change -i or other parameter?

i really love the speed improvement but not sable enough for me right now

ccminer 818
hsrminer test version

thanks for any help

try -i 3 or 4

edit: btw 1350MH on neoscrypt on 1060? you are wizard :-D if you have tdp +120 then it should be possible ....

[LuckLurker]

I have three 1080tis with 34gb page file & 8gb ram but the miner keeps closing after 10 minutes or so. It does however works flawlessly on my 1070 gaming rig. Any solutuins? I really wanna mine neoscrypt using this miner as its way faster than the others out there.

Hi, with what error message or exception does it close? What about OC? What version do you use, main or test?

No overclock, latest test version and I get "cuda error in func 'neoscrypt_cpu_hash_1080' at launch timed out and was terminated"

[melpheos]

In a quick test with test neoscrypt version with -i 17.8 on a 1070 i go from 1037mh/s to 1095mh/s so the 1% dev fee i well deserved
I'll put it on my two 6*1070ti and check the results but that's a net 4.5% increase in hashrate  

edit: on my two rigs i go from 8025 to 8325 so if you remove the dev fee i'm at 8240 so that's a 2.6% net increase. Not as good as with my 1070 but still a very nice improvement over ccminer 818

i have on my 1070s about 1140+-MH (95tdp, +107core, +350mem) and if there is -i option, then 4 ... how can you have there 17.8 :-D everything over 5 was crash to my gpus (1080ti inc.)

Well it did crash :p but after some time and in strange way.
In one case, the card continued to use power but there was no update on screen
In another case, there was no update on screen but card stopped hashing
In the last case, i got continuous "cannot connect to pool, try again in 10 seconds" despite pool working OK on the other rig.

Regarding intensity, i have my virtual memory setup to 80Go. Without that much, the miner will crash straigh away.

I tested also without intensity settings and there was still crashes so i'm not sure if the intensity settings is relevant here....