leowonderful
Legendary
 Offline
Activity: 1624
Merit: 1129
Bitcoin FTW!
|
 |
March 03, 2017, 12:20:44 AM |
|
Dunno if this has already been answered or not, but recently after I unplugged and re plugged in my PSU to the SP20E I can't connect to it anymore; I try to connect to it but Chrome and other browsers just report that the connection is being refused. The bottom LED seems to light up and go away, then there isn't anything lit up except for the Ethernet port. I've unsuccessfully tried to reflash the miner with my MicroSD; I might've waited less time than required or something of the sort.. not sure if there's any indicator of a completed reflashing of these miners based on LED colors or anything. Before I go try to mess with the miner again, should I give the boot sd a shot? I've been using the recovery files but I figured the booting might be the issue.
Did see something about putting the microsd in with the recovery files and then pulling it out right after the miner reads the files on the sd on the fake sptech site.. haven't tried that out yet, though.
|
|
|
|
|
|
|
|
|
|
|
|
The Bitcoin software, network, and concept is called "Bitcoin" with a capitalized "B". Bitcoin currency units are called "bitcoins" with a lowercase "b" -- this is often abbreviated BTC.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
xkoboldx
Newbie
Offline
Activity: 2
Merit: 0
|
|
March 18, 2017, 11:23:07 AM |
|
Please, i need the sd recovery image....
Can anybody help me?
|
|
|
|
|
|
Nam3
|
|
March 18, 2017, 12:17:22 PM |
|
Please, i need the sd recovery image....
Can anybody help me?
What version are you looking for? |
|
|
|
|
xkoboldx
Newbie
Offline
Activity: 2
Merit: 0
|
|
March 18, 2017, 12:27:08 PM |
|
Please, i need the sd recovery image....
Can anybody help me?
What version are you looking for? newest is better, but any version works for me, please I have an SP20 |
|
|
|
|
|
LASERminer
|
|
March 18, 2017, 12:33:31 PM |
|
newest is better, but any version works for me, please
I have an SP20
Here you go: last standard version 2.6.14 Recovery image to re-flash miner, SD Boot image to run miner of SD Card. |
|
|
|
|
timpalmieri
Newbie
Offline
Activity: 1
Merit: 0
|
|
December 24, 2017, 01:25:10 AM |
|
Hey forum,
Please help me out, super frustrated. I have my sp20e hooked up and when I type in my pool's URL and username and everything it says that there is an error with the CGMiner??? What even is that? It says CGMiner Version N/A, CGMiner Status Not running... Also, what is MinerGate? Thoroughly confused. Please help.
|
|
|
|
|
edgar
Legendary
Offline
Activity: 1848
Merit: 1001
|
|
January 15, 2018, 10:09:16 AM |
|
sounds like a possibly dead controller card.
have u taken it apart to check all connections are snug?
|
|
|
|
|
crushed
Member
Offline
Activity: 103
Merit: 11
|
|
January 15, 2018, 03:09:31 PM |
|
Hey forum,
Please help me out, super frustrated. I have my sp20e hooked up and when I type in my pool's URL and username and everything it says that there is an error with the CGMiner??? What even is that? It says CGMiner Version N/A, CGMiner Status Not running... Also, what is MinerGate? Thoroughly confused. Please help.
If checking cables/connections doesn't work out, you might also want to try reflashing the ROM image that someone linked above in the event there was some corruption. If neither of those things work, your controller board could be dead. |
|
|
|
|
ymdurand
Newbie
Offline
Activity: 1
Merit: 0
|
|
April 15, 2018, 08:51:52 PM |
|
Good afternoon, I have an SP20E and it gives me an error .. it does not connect to the pool
stats
LOOP[0] OFF TO:0 (test serial failed)
0: disabled (REMOVED/DISABLED)
1: disabled (REMOVED/DISABLED)
LOOP[1] ON TO:0 (w:0)
2: DC2DC/1/:[vlt1:0 vlt2:688(DCl:794 Tl:794 Ul:749) 0W 0A 0c] ASIC:[ 85c (125c) 950hz(BL: 950) 0 (E:193) F:0 L:0]
3: DC2DC/1/:[vlt1:0 vlt2:688(DCl:794 Tl:794 Ul:749) 0W 0A 0c] ASIC:[ 85c (125c) 950hz(BL: 950) 0 (E:192) F:0 L:0]
LOOP[2] ON TO:0 (w:0)
4: DC2DC/1/:[vlt1:0 vlt2:688(DCl:794 Tl:794 Ul:749) 0W 0A 0c] ASIC:[ 85c (125c) 890hz(BL: 890) 0 (E:193) F:0 L:0]
5: DC2DC/1/:[vlt1:0 vlt2:688(DCl:794 Tl:794 Ul:749) 0W 0A 0c] ASIC:[ 85c (125c) 830hz(BL: 830) 0 (E:193) F:0 L:0]
LOOP[3] ON TO:0 (w:0)
6: DC2DC/1/:[vlt1:0 vlt2:688(DCl:794 Tl:794 Ul:749) 0W 0A 0c] ASIC:[ 85c (125c) 890hz(BL: 890) 0 (E:193) F:0 L:0]
7: DC2DC/1/:[vlt1:0 vlt2:688(DCl:794 Tl:794 Ul:749) 0W 0A 0c] ASIC:[ 85c (125c) 840hz(BL: 840) 0 (E:189) F:0 L:0]
i try everything possible, change cable, factory reset, i disable loop 0 .. and not work please help me
|
|
|
|
|
|
