How to upgrade TPLINK TL-MR3020 firmware to technobit openwrt

[Zich]

Thank you so much, TL MR3020 router I've run yesterday, then I have problems again .. I can not enter setup, because I have to change settings become wan lan, I have tried to install and unplug lan cable and power supply but still not managed to get openwrt. .
I have tried to ping the IP Address and successful but when I tried to get in openwrt, I could not connect, whether it is the effect of changes lan wan interface to that?
Can I restore into a lan wan interface?
I asked for help to change it, because I've tried all night to this day still does not successfully connect openwrt ..

I change the lan interface in this section

http://postimg.org/image/dz53zwnb9/full/

please

Try this step:

Set your computer's IP to 192.168.1.2, subnet 255.255.255.0
Connect the TL-MR3020 to your computer via ethernet
Power on the TL-MR3020
When the WPS button starts to blink:
on BB (Breaking Barrier / trunk) move the sliding switch quickly from one side to the other.
Do this until the WPS button starts blinking faster.
The device is now in Failsafe-Mode
You may access it by using telnet 192.168.1.1
Info on resetting to OpenWrt defaults can be found at: generic.failsafe

If still fail to login, then you need to use serial console.
You will need to make serial adapter using CA42 & open your TL-MR3020 then add some pin on P1.
More info: http://wiki.openwrt.org/toh/tp-link/tl-mr3020

[pratama_herdy]

thank you, I still can not connect, this may be result that I can not use completely openwrt 

[marto74]

0.3.4* cgminer for hex BTC Miners - patch to cgminer 4.3.4 rev_c1d58161486db4ccd44a27bf43ab682017284608.patch* cgminer for hex Scrypt Miners - patch to cgminer 4.3.4 srev_c1d58161486db4ccd44a27bf43ab682017284608.patch* SCgminer is not tested om LE (i386) there might be some endianess issues!!!!!* openwrt updated to r40996* openwrt web new config tabs* Please disable from ssh all services that are not needed/etc/init.d/luci_fixtime disable/etc/init.d/luci_dhcp_migrate disable/etc/init.d/telnet disable/etc/init.d/sysntpd disable/etc/init.d/led disable/etc/init.d/log disable/etc/init.d/(s)cgminer disable – If you happen to have both LTC and BTC miners leave both enabled
* HEXs (HEX8A2) scrypt options  1200 / 980 mV

http://technobit.eu/0_3_4.rar


Todo
* Work on Minion and prepare for board launch.
* HEXS cleanup, testing bugs an so on in preparation for the board launch - Done
* HEX8A1 4 chip cleanup, testing bugs an so on in preparation for the board launch - done
* HEX8A1 cleanup, testing bugs an so on in preparation for the board launch - done
* add support for HEX8A1 - 6/8 chip Coincraft A1 board aslso known as HEX8 - done
* finish cgminer nanofury support - done
* add cgminer monitor script - done
* stay in sync with official cgminer git and build fresh openwrt images - synced
* add auto frequency adjustment support avalon-auto style - canceled
* add configuration options (voltage and clock) per board based on HEX16A serial number - canceled

HowTo Compile:
1. Download cgminer git to match with patch revision
2. cd cgminer
3. patch -p1 < /path_to_patch/9ce30b7bdf5d6756046f83e4f0d97da421963002.patch (example)
4. ./autogen.sh --enable-hexminera --enable-hexminerb --enable-hexminerc --enable-hexmineru --enable-hexminer8
5. make
6. Scrypt - ./autogen.sh --enable-hexminers

[Kenji1337]

Hello I'm new here and have a question. I am interested very much for this box. I have RipeNcc get a few of these samples and still have a choice.

 I would like to flash to openwrt. I only have the problem that I can not logging in the Web Interface or via Telnet.

It seems that it will be locked?. If the only options via serial adapter to flash?

Excuse me for my bad english

[Zich]

Hello I'm new here and have a question. I am interested very much for this box. I have RipeNcc get a few of these samples and still have a choice.

 I would like to flash to openwrt. I only have the problem that I can not logging in the Web Interface or via Telnet.

It seems that it will be locked?. If the only options via serial adapter to flash?

Excuse me for my bad english

If you can not log into web interfaces after following the step on OP, maybe your unit is bricked. Then the only way is using serial console.

[Zich]

*0.3.5 Minion release http://technobit.eu/0_3_5_Final_ok.rar

OP updated

[Scrappy Do]

 Thank you so much Zich for the link in the other thread. I am more confused now then before. If I am reading this right, I need this device and then a 48 port switch to connect the 50 boards to as well? Or do I need more than 1 tp link to do that many boards?

[loshia]

Thank you so much Zich for the link in the other thread. I am more confused now then before. If I am reading this right, I need this device and then a 48 port switch to connect the 50 boards to as well? Or do I need more than 1 tp link to do that many boards?

You need 5 tplinks and 5 10 port USB hubs
That is what I would do.
What power supplies  are  you going to use?

[sorehammer]

Will a new settings image for the mininon settings be possible soon.

[marto74]

Will a new settings image for the mininon settings be possible soon.

It is on our website/download section

[sorehammer]

marto I have downloaded the tp-link update will that put the settings into the config page for voltage and frequency and the like.

[Scrappy Do]

Thank you so much Zich for the link in the other thread. I am more confused now then before. If I am reading this right, I need this device and then a 48 port switch to connect the 50 boards to as well? Or do I need more than 1 tp link to do that many boards?

You need 5 tplinks and 5 10 port USB hubs
That is what I would do.
What power supplies  are  you going to use?

 Looking at going this direction.. https://bitcointalk.org/index.php?topic=637595.new#new

[Zich]

marto I have downloaded the tp-link update will that put the settings into the config page for voltage and frequency and the like.

You can manually input the value if it still blank. Make sure to fill in the value on all board. Otherwise cgminer wil not start

[sorehammer]

marto I have downloaded the tp-link update will that put the settings into the config page for voltage and frequency and the like.

You can manually input the value if it still blank. Make sure to fill in the value on all board. Otherwise cgminer wil not start

So are these settings 100ghs or 120ghs

[marto74]

marto I have downloaded the tp-link update will that put the settings into the config page for voltage and frequency and the like.

You can manually input the value if it still blank. Make sure to fill in the value on all board. Otherwise cgminer wil not start

So are these settings 100ghs or 120ghs

These are a little bit more than 400.
120 GHs per chip is heavy overclocked mode .
I would run them @ 100

[sorehammer]

cool so what have you got them up to safely with overclocking

[Pistachio]

Does this image work with the TL-703N or those old wiibox controllers from Gridseed?

[loshia]

Does this image work with the TL-703N or those old wiibox controllers from Gridseed?

Most probably no...

[Scrappy Do]

 Ok, so to confirm.. I can run the 5 tp-links all off the same switch. I do not need a separate switch for each 10 boards correct?

[loshia]

Ok, so to confirm.. I can run the 5 tp-links all off the same switch. I do not need a separate switch for each 10 boards correct?

Wrong you need 5 separate switches or USB hubs for each tplink. However you can use one LAN switch to connect Ethernet cables