Artemis3
Legendary
Offline
Activity: 2030
Merit: 1563
CLEAN non GPL infringing code made in Rust lang
|
|
December 19, 2018, 05:47:41 PM Last edit: December 21, 2018, 08:04:13 PM by Artemis3 Merited by frodocooper (3) |
|
Can you give us install steps for the "alternative image flashable via Antminer web interface"? That would be greatly appreciated.
If you own an S9: In the Antminer web UI... - System -> Upgrade -> Flash new firmware image.
You won't get a backup of the factory firmware if you use this method... To use the other method you don't need any "linux skills", you only need python installed, as the instructions clearly indicate here: https://docs.braiins-os.org/#phase-2-permanently-migrating-from-factory-firmware-to-braiins-osIIRC you will get a new mac address so your devices will probably need to be reconfigured for network again, and you might need to scan your network to find them again. No, the Bitmain tool won't work anymore, you need another network scanner (or check your router dhcp server). So consider doing this on site if you are not confident.
|
█████████████████████████ ██████████████████████████ ██████████████████████████ ███████████████████████████ | BRAIINS OS+| | AUTOTUNING MINING FIRMWARE| | Increase hashrate on your Bitcoin ASICs, improve efficiency as much as 25%, and get 0% pool fees on Braiins Pool | |
|
|
|
studio_mining
Jr. Member
Offline
Activity: 33
Merit: 10
|
|
December 21, 2018, 02:55:49 PM Last edit: December 21, 2018, 09:05:08 PM by studio_mining |
|
Is there way to retain the current MAC address of the units when upgrading directly without SD card step?
UPDATE: The MAC address stays the same; but DHCP server of my router assigns the machine a new IP. The hostname is the same 'antMiner'; anyone come up with a solution where it will connect to the network and bind to the same IP? (Other than assigning static IPs via the router)
|
|
|
|
score1more
Newbie
Offline
Activity: 60
Merit: 0
|
|
December 22, 2018, 02:07:41 AM Last edit: December 22, 2018, 02:48:12 AM by frodocooper |
|
[...]
Thank you for releasing this software. The installation was well-documented and easy to follow. I'm getting the same hash rate with 1 amp less of input power. And thanks Bitmain... for using an unfair advantage.
|
|
|
|
rahuldel
Newbie
Offline
Activity: 17
Merit: 0
|
|
December 25, 2018, 04:25:19 PM |
|
The miner status is not visible........although the miner is working fine.
What can be done to resolve the following ?
Miner Status API connection status: Not connected
|
|
|
|
sarcheer
Copper Member
Full Member
Offline
Activity: 330
Merit: 103
|
|
December 25, 2018, 06:12:05 PM |
|
The miner status is not visible........although the miner is working fine.
What can be done to resolve the following ?
Miner Status API connection status: Not connected
Is the miner hashing pool side?
|
Miners: Avalon 1041, Whatsminer M10, Antminer T15 x 2, DragonMint T1 x 3, Innosilicon T2T, R4 x 2
|
|
|
rahuldel
Newbie
Offline
Activity: 17
Merit: 0
|
|
December 25, 2018, 06:18:15 PM Last edit: December 25, 2018, 10:34:56 PM by frodocooper |
|
Yes the miner is working fine pool side. I am using a SDCard and did a fresh firmware and have tried two different cards but the same results, the old firmware works fine. Only thing is it is not showing the miner screen and it is saying Miner Status API connection status: Not connected
|
|
|
|
score1more
Newbie
Offline
Activity: 60
Merit: 0
|
|
December 26, 2018, 04:08:24 PM |
|
I've found that the API crashes if you leave the miner status page up in your browser. I've stopped leaving the page open and only check it periodically. Seems to help.
If you go to Services > Miner and click save/apply. It'll restart the miner and the API used by the monitor page.
|
|
|
|
balla69
Newbie
Offline
Activity: 75
Merit: 0
|
|
December 26, 2018, 06:35:37 PM |
|
hello, i installed braiins os by web on s9 13.5 all good, but when i go to cgminer, i have error /usr/lib/lua/luci/dispatcher.lua:460: Failed to execute cbi dispatcher target for entry '/admin/services/cgminer'. The called action terminated with an exception: /usr/lib/lua/luci/model/cbi/cgminer.lua:297: default configuration not available, create /etc/cgminer.conf stack traceback: [C]: in function 'assert' /usr/lib/lua/luci/dispatcher.lua:460: in function 'dispatch' /usr/lib/lua/luci/dispatcher.lua:141: in function </usr/lib/lua/luci/dispatcher.lua:140> How can i fix? Thanks
|
|
|
|
Artemis3
Legendary
Offline
Activity: 2030
Merit: 1563
CLEAN non GPL infringing code made in Rust lang
|
|
December 27, 2018, 12:56:53 AM |
|
/usr/lib/lua/luci/model/cbi/cgminer.lua:297: default configuration not available, create /etc/cgminer.conf How can i fix? I have experienced that one before... Try removing the package firmware from the web ui or from ssh with the command opkg remove firmware.
|
█████████████████████████ ██████████████████████████ ██████████████████████████ ███████████████████████████ | BRAIINS OS+| | AUTOTUNING MINING FIRMWARE| | Increase hashrate on your Bitcoin ASICs, improve efficiency as much as 25%, and get 0% pool fees on Braiins Pool | |
|
|
|
balla69
Newbie
Offline
Activity: 75
Merit: 0
|
|
December 27, 2018, 12:01:54 PM Last edit: December 27, 2018, 11:44:15 PM by frodocooper |
|
Thanks, now it's started, but i don't like.... only 13 Th/s with 1200w How can i install the bitmain firmware?
|
|
|
|
sergw
Member
Offline
Activity: 159
Merit: 12
|
|
December 27, 2018, 01:40:02 PM Last edit: December 27, 2018, 11:44:30 PM by frodocooper |
|
Thanks, now it's started, but i don't like.... only 13 Th/s with 1200w How can i install the bitmain firmware?
try to increase voltage on all boards. fe for freq 650 (14Th) it should be 8.8 volt.
|
|
|
|
balla69
Newbie
Offline
Activity: 75
Merit: 0
|
|
December 27, 2018, 02:44:44 PM |
|
Yes, but i wish to optimize the efficiency, with bitmain firmware i mine 9,3 Th/s with 706W eff. 0,76. The difficult is come back to bitmain firmware... I don't have a backup.... how can i fix this? I've another s9 for make the backup, but there's the instruction only for create a backup without install ?
|
|
|
|
sergw
Member
Offline
Activity: 159
Merit: 12
|
|
December 27, 2018, 03:16:18 PM |
|
Yes, but i wish to optimize the efficiency, with bitmain firmware i mine 9,3 Th/s with 706W eff. 0,76. The difficult is come back to bitmain firmware... I don't have a backup.... how can i fix this? I've another s9 for make the backup, but there's the instruction only for create a backup without install ?
if you dont have backup - then you need to use SD card to boot asic and flash bitmain fw.
|
|
|
|
balla69
Newbie
Offline
Activity: 75
Merit: 0
|
|
December 27, 2018, 04:16:42 PM Last edit: December 27, 2018, 11:45:21 PM by frodocooper |
|
I've prepare a ssd with brains firmware, Can i put the firmware bitmain in the ssd, change the switch for start from ssd, start and flash the bitmain firmware? Or I must be install the firmware braiins in another s9 from sd card, after restore the save firmware and after restore also into the first s9?
|
|
|
|
sergw
Member
Offline
Activity: 159
Merit: 12
|
|
December 27, 2018, 08:11:42 PM Last edit: December 27, 2018, 11:46:07 PM by frodocooper |
|
Can i put the firmware bitmain in the ssd, change the switch for start from ssd, start and flash the bitmain firmware?
yep
|
|
|
|
Bitcguru77
Jr. Member
Offline
Activity: 48
Merit: 14
|
|
December 28, 2018, 11:26:30 AM Last edit: December 28, 2018, 11:44:57 PM by frodocooper |
|
Hi all.
I tried Wolfram in my S9 earlier (and loved it), but I've now been offline for a while due to low bitcoin price.
Yesterday however I jumped back in after putting Cobalt (love it even more) on both my own and my friends SD-card.
Long story short:
My S9 - 13.5 THs February 2018 batch - Firmware: November 2017 autofrequency + November 2018 LPM - Running Cobalt from SD-card - Works like a charm
My friends S9 - 13.5 THs older batch (not sure how old, but newer than C5 control board) - Firmware: November 2017 autofrequency + November 2018 LPM - Running Cobalt from SD-card - No temp-readings and fans running full speed. Otherwise works like a charm.
So any solution to this yet?
BR. Steff
|
|
|
|
balla69
Newbie
Offline
Activity: 75
Merit: 0
|
|
December 28, 2018, 04:06:39 PM Last edit: December 28, 2018, 11:46:11 PM by frodocooper |
|
I've create an sd card with Etcher and i put the original bios (Antminer-S9-all-201812051512-autofreq-user-Update2UBI-NF.tar.gz) into the sd card, switch jumper for start from sd and run the s9. I've download the ssh version and type this command from terminal. Where's the error? free@srv-1 ~/Scaricati/braiins-os_am1-s9_ssh_2018-11-27-0-c34516b0 $ python3 restore2factory.py Antminer-S9-all-201812051512-autofreq-user-Update2UBI-NF.tar.gz 172.16.0.134 Traceback (most recent call last): File "restore2factory.py", line 25, in <module> import upgrade.platform as platform File "/home/free/Scaricati/braiins-os_am1-s9_ssh_2018-11-27-0-c34516b0/upgrade/platform.py", line 29, in <module> from .transfer import Progress File "/home/free/Scaricati/braiins-os_am1-s9_ssh_2018-11-27-0-c34516b0/upgrade/transfer.py", line 25, in <module> from progress.bar import Bar ImportError: No module named 'progress'
|
|
|
|
sarcheer
Copper Member
Full Member
Offline
Activity: 330
Merit: 103
|
|
December 28, 2018, 07:41:20 PM Last edit: December 28, 2018, 11:46:47 PM by frodocooper |
|
I've create an sd card with Etcher and i put the original bios (Antminer-S9-all-201812051512-autofreq-user-Update2UBI-NF.tar.gz) into the sd card, switch jumper for start from sd and run the s9. I've download the ssh version and type this command from terminal. Where's the error?
[...]
Did you run (linux): cd braiins-os_am1-s9_ssh_VERSION virtualenv --python=/usr/bin/python3 .env source .env/bin/activate pip install -r ./requirements.txt
That is what fixed that error for me and was the recommendation from Braiins support. Seems you need to be using virtualenv and install everything in requirements.txt so that you have a proper python3 environment.
|
Miners: Avalon 1041, Whatsminer M10, Antminer T15 x 2, DragonMint T1 x 3, Innosilicon T2T, R4 x 2
|
|
|
Velles2003
Newbie
Offline
Activity: 8
Merit: 6
|
|
December 28, 2018, 09:12:16 PM |
|
this seems odd to me, running on default settings and lpm off: voltage and frequency seem off:8.9V and 650MHZ (when should be 630MHZ), temperatures are high and also, the hash rate on overclock doesn't get reported pool-side to be like the S9 reports it https://imgur.com/a/pxkRpgg
|
|
|
|
Shad0wSmurf
Jr. Member
Offline
Activity: 59
Merit: 10
|
|
December 29, 2018, 01:20:53 AM Last edit: December 29, 2018, 09:54:01 AM by frodocooper |
|
this seems odd to me, running on default settings and lpm off: voltage and frequency seem off:8.9V and 650MHZ (when should be 630MHZ), temperatures are high and also, the hash rate on overclock doesn't get reported pool-side to be like the S9 reports it https://imgur.com/a/pxkRpggI'd drop those volts, my lord. I can run 800mhz at 8.8v with BARELY any he errors. For those low frequencies I'd drop the volts to 8.4 or 8.5 and then, your heat will drop. Turn lpm on. And you will see the advantages. You're going to burn up your hashboards with that high volts and low frequencies.
|
|
|
|
|