KopiemTu 3.0 - ethash & equihash - NVIDIA USB linux distro

[jk_14]

ZCASH new version, ~80 sols/s on 1070

Code:

cd /root; mine stop; monitor stop
rm -rf /opt/miners/silentarmy
rm -f /root/silentarmy.tgz

wget http://mbl.cash/silentarmy.tgz
tar -xPf silentarmy.tgz

screen -dmS miner /opt/miners/silentarmy/silentarmy --use 0,1,2,3 --instances=1 -c stratum+tcp://us1-zcash.flypool.org:3333 -u t1gxfd218jLgVayKwRz3sHPiNfb322Yvp7j

screen -r

I don't see any impact if power limit is set to lowest:
nvidia-smi -pl 75

[etang6000]

ZCASH new version, ~80 sols/s on 1070

Code:

cd /root; mine stop; monitor stop
rm -rf /opt/miners/silentarmy
rm -f /root/silentarmy.tgz

wget http://mbl.cash/silentarmy.tgz
tar -xPf silentarmy.tgz

screen -dmS miner /opt/miners/silentarmy/silentarmy --use 0,1,2,3 --instances=1 -c stratum+tcp://us1-zcash.flypool.org:3333 -u t1gxfd218jLgVayKwRz3sHPiNfb322Yvp7j

screen -r

I don't see any impact if power limit is set to lowest:
nvidia-smi -pl 75

Can you get the nicehash miner to work on Linux ?

[hoze]

ZCASH new version, ~80 sols/s on 1070

Code:

cd /root; mine stop; monitor stop
rm -rf /opt/miners/silentarmy
rm -f /root/silentarmy.tgz

wget http://mbl.cash/silentarmy.tgz
tar -xPf silentarmy.tgz

screen -dmS miner /opt/miners/silentarmy/silentarmy --use 0,1,2,3 --instances=1 -c stratum+tcp://us1-zcash.flypool.org:3333 -u t1gxfd218jLgVayKwRz3sHPiNfb322Yvp7j

screen -r

I don't see any impact if power limit is set to lowest:
nvidia-smi -pl 75

Zcash ~54sols/s on 1060 6gb

Total 100.3 sol/s [dev0 51.4, dev1 49.1] 17 shares
Total 100.3 sol/s [dev0 52.7, dev1 48.3] 17 shares
Total 100.3 sol/s [dev0 52.8, dev1 47.3] 17 shares
Total 101.2 sol/s [dev0 54.3, dev1 47.6] 17 shares
Total 101.9 sol/s [dev0 55.5, dev1 49.8] 17 shares
Total 102.1 sol/s [dev0 52.6, dev1 49.6] 19 shares
Total 102.2 sol/s [dev0 52.9, dev1 49.2] 19 shares
Total 102.7 sol/s [dev0 54.2, dev1 49.0] 19 shares

Not bad, but we need more for NVIDIA!

[jk_14]

Zcash ~54sols/s on 1060 6gb

Total 100.3 sol/s [dev0 51.4, dev1 49.1] 17 shares
Total 100.3 sol/s [dev0 52.7, dev1 48.3] 17 shares
Total 100.3 sol/s [dev0 52.8, dev1 47.3] 17 shares
Total 101.2 sol/s [dev0 54.3, dev1 47.6] 17 shares
Total 101.9 sol/s [dev0 55.5, dev1 49.8] 17 shares
Total 102.1 sol/s [dev0 52.6, dev1 49.6] 19 shares
Total 102.2 sol/s [dev0 52.9, dev1 49.2] 19 shares
Total 102.7 sol/s [dev0 54.2, dev1 49.0] 19 shares

Not bad, but we need more for NVIDIA!

ZCASH with monitoring support:

(stop your zcash mining on screen manually first, if running)

Code:

cd /root; mine stop; monitor stop
rm -rf /opt/miners/silentarmy
rm -f /root/silentarmy.tgz

wget http://mbl.cash/silentarmy.tgz
tar -xPf silentarmy.tgz

mine switch

mine start
monitor start

[induktor]

Hi!
I try to make that work on kopiemtu 2 mod 4, and no go, i got the ensure_future crap, i already have the newest version of python but the program still doesn't see it any ideas?

I will switch to kopiemtu 3 but when i have ethereum working (still have some OpenCL errors when i compile).

how do you set pl to 75 ? the minimum of my GTX 1070 is 90

[_javi_]

hi, would you plz include Optiminer or guide us on a how-to-do so? thanks!

https://github.com/Optiminer/OptiminerZcash

I wonder why Optiminer is not even mentioned on btctalk forums.. 

[hoze]

Zcash ~54sols/s on 1060 6gb

Total 100.3 sol/s [dev0 51.4, dev1 49.1] 17 shares
Total 100.3 sol/s [dev0 52.7, dev1 48.3] 17 shares
Total 100.3 sol/s [dev0 52.8, dev1 47.3] 17 shares
Total 101.2 sol/s [dev0 54.3, dev1 47.6] 17 shares
Total 101.9 sol/s [dev0 55.5, dev1 49.8] 17 shares
Total 102.1 sol/s [dev0 52.6, dev1 49.6] 19 shares
Total 102.2 sol/s [dev0 52.9, dev1 49.2] 19 shares
Total 102.7 sol/s [dev0 54.2, dev1 49.0] 19 shares

Not bad, but we need more for NVIDIA!

ZCASH with monitoring support:

(stop your zcash mining on screen manually first, if running)

Code:

cd /root; mine stop; monitor stop
rm -rf /opt/miners/silentarmy
rm -f /root/silentarmy.tgz

wget http://mbl.cash/silentarmy.tgz
tar -xPf silentarmy.tgz

mine switch

mine start
monitor start

Is there a gui in kopiemtu 3? If yes, how to run?

[jk_14]

Is there a gui in kopiemtu 3? If yes, how to run?

Yes, there is, you can start it by single command below,
GUI is not started by default, while is not necessary for mining,
and you may even not notice that, if you have headless rig

Code:

service lightdm start

or

Code:

systemctl enable lightdm.service
service lightdm start

the first will start GUI one time, the second sequence will start and activate it permanently

All that information is in very first lines of /root/README.txt

Code:

root@kopiemtu:~# cat README.txt

One-time graphical interface (as root):
service lightdm start

Permanent graphical interface (as root):
systemctl enable lightdm.service


------------
Quick setup:
------------

cd /etc/kopiemtu; ls -l
nano lbry.conf
...
mine switch|start|stop|status
monitor start|stop|status

tail -f /var/log/syslog
http://your_rig_IP/


=================================
Master setup, on SINGLE RIG ONLY!
=================================

nano /root/.master.conf
mv /root/.master.conf /root/master.conf
init 6

ssh-keygen -q -P "" -f /root/.ssh/id_rsa
scp /root/.ssh/id_rsa.pub localhost:/root/.ssh/authorized_keys
scp /root/.ssh/id_rsa.pub w12:/root/.ssh/authorized_keys
scp /root/.ssh/id_rsa.pub w21:/root/.ssh/authorized_keys
scp /root/.ssh/id_rsa.pub w22:/root/.ssh/authorized_keys
...
<until your last rig>


Verify your configuration:

mm uptime
mm "nvidia-smi | grep %"
mmnv

mmis
mmos

mmit
mmip
mmih

mmot
mmip

mm ssh

=================================
KopiemTu 3.0 is distributed under six-beers license. If you want to use it - you must send me six beers.
For simplicity - send 0.01 btc to my smartphone: 1JofTuhjgxuQAEtqyCdj7JNwzrZ1f7EXcg
(no doubt I will utilise it for six beers :)

Vertcoin: Vh9VgXbQN9DdcUJzt5mrxZYWHKpoNgemmJ
MobileCash: MBeBwseXEwVmPg8cvQrEFSCXVnL5q3n3LP

root@kopiemtu:~#

[jk_14]

Hi!
I try to make that work on kopiemtu 2 mod 4, and no go, i got the ensure_future crap, i already have the newest version of python but the program still doesn't see it any ideas?

I will switch to kopiemtu 3 but when i have ethereum working (still have some OpenCL errors when i compile).

how do you set pl to 75 ? the minimum of my GTX 1070 is 90

if I good remember, that is due to vBIOS version,
On old vBIOS I had minimum 85W.

on very recent I have:
root@kopiemtu:~# nvidia-smi -pl 70
Provided power limit 70.00 W is not a valid power limit which should be between 75.00 W and 225.00 W for GPU 0000:01:00.0
Terminating early due to previous errors.

and default is not 170, but 195W

Nov 14 18:45:49 kopiemtu mine[1630]: Power limit for GPU 0000:01:00.0 was set to 75.00 W from 195.00 W.
Nov 14 18:45:49 kopiemtu mine[1630]: Power limit for GPU 0000:02:00.0 was set to 75.00 W from 195.00 W.


P.S. you can use this for Ethereum:
https://bitcointalk.org/index.php?topic=520998.msg16801839#msg16801839

[jk_14]

Can you get the nicehash miner to work on Linux ?

there were errors during compilation...

[hoze]

Is there a gui in kopiemtu 3? If yes, how to run?

Yes, there is, you can start it by single command below,
GUI is not started by default, while is not necessary for mining,
and you may even not notice that, if you have headless rig

Code:

service lightdm start

or

Code:

systemctl enable lightdm.service
service lightdm start

the first will start GUI one time, the second sequence will start and activate it permanently

All that information is in very first lines of /root/README.txt

Code:

root@kopiemtu:~# cat README.txt

One-time graphical interface (as root):
service lightdm start

Permanent graphical interface (as root):
systemctl enable lightdm.service


------------
Quick setup:
------------

cd /etc/kopiemtu; ls -l
nano lbry.conf
...
mine switch|start|stop|status
monitor start|stop|status

tail -f /var/log/syslog
http://your_rig_IP/


=================================
Master setup, on SINGLE RIG ONLY!
=================================

nano /root/.master.conf
mv /root/.master.conf /root/master.conf
init 6

ssh-keygen -q -P "" -f /root/.ssh/id_rsa
scp /root/.ssh/id_rsa.pub localhost:/root/.ssh/authorized_keys
scp /root/.ssh/id_rsa.pub w12:/root/.ssh/authorized_keys
scp /root/.ssh/id_rsa.pub w21:/root/.ssh/authorized_keys
scp /root/.ssh/id_rsa.pub w22:/root/.ssh/authorized_keys
...
<until your last rig>


Verify your configuration:

mm uptime
mm "nvidia-smi | grep %"
mmnv

mmis
mmos

mmit
mmip
mmih

mmot
mmip

mm ssh

=================================
KopiemTu 3.0 is distributed under six-beers license. If you want to use it - you must send me six beers.
For simplicity - send 0.01 btc to my smartphone: 1JofTuhjgxuQAEtqyCdj7JNwzrZ1f7EXcg
(no doubt I will utilise it for six beers :)

Vertcoin: Vh9VgXbQN9DdcUJzt5mrxZYWHKpoNgemmJ
MobileCash: MBeBwseXEwVmPg8cvQrEFSCXVnL5q3n3LP

root@kopiemtu:~#

Thanks.
I didn't read the readme file 

[induktor]

Hi!
I try to make that work on kopiemtu 2 mod 4, and no go, i got the ensure_future crap, i already have the newest version of python but the program still doesn't see it any ideas?

I will switch to kopiemtu 3 but when i have ethereum working (still have some OpenCL errors when i compile).

how do you set pl to 75 ? the minimum of my GTX 1070 is 90

if I good remember, that is due to vBIOS version,
On old vBIOS I had minimum 85W.

on very recent I have:
root@kopiemtu:~# nvidia-smi -pl 70
Provided power limit 70.00 W is not a valid power limit which should be between 75.00 W and 225.00 W for GPU 0000:01:00.0
Terminating early due to previous errors.

and default is not 170, but 195W

Nov 14 18:45:49 kopiemtu mine[1630]: Power limit for GPU 0000:01:00.0 was set to 75.00 W from 195.00 W.
Nov 14 18:45:49 kopiemtu mine[1630]: Power limit for GPU 0000:02:00.0 was set to 75.00 W from 195.00 W.


P.S. you can use this for Ethereum:
https://bitcointalk.org/index.php?topic=520998.msg16801839#msg16801839

That means I need to flash the cards???  that's cary when they don't have bios switch like the AMD had.

[induktor]

Update!, thanks to _javi_ here i was able to compile and run krnlx flavor of nheqminer

he says that we can get 92 sol/s per GTX 1070, i'm only gettin 71 Sol/s but not bad!!!!

most of the compiling issues has to do with the GCC version (4.9.4 or newer required)
and some touches in CMakeCache and CMakeLists but it works very well.

but i read that there are guys with RX480 getting 120 sol/s geez!, that makes our powerful-misused GTX 1070 not recommended for zcash for now right?
what do you think?

how much are you getting with you version at 90W (or lower TDP? (non-OC of course))

[jk_14]

That means I need to flash the cards???  that's cary when they don't have bios switch like the AMD had.

my 1070 babies have that switch, too

[jk_14]

Update!, thanks to _javi_ here i was able to compile and run krnlx flavor of nheqminer

he says that we can get 92 sol/s per GTX 1070, i'm only gettin 71 Sol/s but not bad!!!!

most of the compiling issues has to do with the GCC version (4.9.4 or newer required)
and some touches in CMakeCache and CMakeLists but it works very well.

but i read that there are guys with RX480 getting 120 sol/s geez!, that makes our powerful-misused GTX 1070 not recommended for zcash for now right?
what do you think?

how much are you getting with you version at 90W (or lower TDP? (non-OC of course))

I have average 76 sol/s @75W
(I picked factory OC'ed 1070 for linux - as I did with 750Ti before)

[induktor]

That means I need to flash the cards???  that's cary when they don't have bios switch like the AMD had.

my 1070 babies have that switch, too

Which 1070's have switch?? if the pins are present in the Gigabyte G1 series i will solder them the switch hehe.

[jk_14]

That means I need to flash the cards???  that's cary when they don't have bios switch like the AMD had.

my 1070 babies have that switch, too

Which 1070's have switch?? if the pins are present in the Gigabyte G1 series i will solder them the switch hehe.

http://www.guru3d.com/articles-pages/palit-geforce-gtx-1060-super-jetstream-review,4.html

that's 1060, the same is for 1070

[jk_14]

hi, would you plz include Optiminer or guide us on a how-to-do so? thanks!

https://github.com/Optiminer/OptiminerZcash

I wonder why Optiminer is not even mentioned on btctalk forums.. 

from README.md...

"Supports:
- Linux 64bit only.
- AMD GCN cards only.

Expected speed (stock card):
- R9 Nano: 185S/s
- R9 290: 140S/s
- RX 470: 130S/s

Windows support may be added in a future version.

No NVIDIA support planned at the moment."

[induktor]

That means I need to flash the cards???  that's cary when they don't have bios switch like the AMD had.

my 1070 babies have that switch, too

Which 1070's have switch?? if the pins are present in the Gigabyte G1 series i will solder them the switch hehe.

http://www.guru3d.com/articles-pages/palit-geforce-gtx-1060-super-jetstream-review,4.html

that's 1060, the same is for 1070

wow! nice!, i have never heard of that card before, it doesn't exists here in my region.
soooo... if that card has bios switch then the feature should be present on others, i will investigate the PCB of the gigabyte g1  thanks!

back in the AMD Litecoin era, i screw so much with the AMD bioses, i bricked my cards easily 200 times hehe trying to find the sweet spot, which i did, but i cannot do the same with nvidia cards unless i have a bios switch

[jk_14]

wow! nice!, i have never heard of that card before, it doesn't exists here in my region.
soooo... if that card has bios switch then the feature should be present on others, i will investigate the PCB of the gigabyte g1  thanks!

back in the AMD Litecoin era, i screw so much with the AMD bioses, i bricked my cards easily 200 times hehe trying to find the sweet spot, which i did, but i cannot do the same with nvidia cards unless i have a bios switch

it might be the same card:
Gainward GeForce GTX 1070 Phoenix Golden Sample

I'm waiting for results of your bios research