sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 05:50:25 PM Last edit: January 21, 2022, 06:11:21 PM by sp_ |
|
Can you suggest a kernel for full AMD rigs? It seems that autotune always select kernel 0.
v1.42 only have one active kernel for AMD About Hiveon pool rejected shares are always a problem, 1/2% average (tried xintensity 71 and 24), while they are close to zero in crazypool or 2miners for example
It used to be higher. We tried to improve it, but it keeps coming back. The hiveon pool have 0% fee, so even with 0.5% rejected you should get more shares than on the other pools you listed. The hiveon pool is using the ETHPROXY protocol and different code in the miner than the 2miners and crazypool.
|
|
|
|
dle378
Copper Member
Newbie
Offline
Activity: 77
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 05:51:20 PM |
|
Added 2x 3080 LHRs to my setup and was hoping to get a stable hash rate on the cards. Any tips or options to add as a starting point?
On windows I use 75% powerlimit and low coreclock as possible on the 3080ti. No need to lock the clock. If the card fail to unlock try with -1, -2, -3, -4 ... etc until it's stable. --lhr-unlock [-1,-1,0,0,0,0] On the Options page, the supported values for LHR-unlock is either 1 (Unlock Mode) or 0 (Normal Mode). ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FINPJawZ.jpg&t=665&c=xV56rZch4ygIig) Should I try negative values this time?
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 05:53:42 PM Last edit: January 21, 2022, 06:10:01 PM by sp_ |
|
Should I try negative values this time?
Yes negative values are supported. The LHR docs are not updated to the later version. My GTX 3070 LHR works best with -4. 60% tdp, 7900Memory/ stable at 44MHASH . I use --log in the batfile
|
|
|
|
dle378
Copper Member
Newbie
Offline
Activity: 77
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 06:03:05 PM |
|
Should I try negative values this time?
Yes negative values are supported. The LHR docs are not updated to the later version. My GTX 3070 LHR works best with -4. Thanks. Any recommendation for a xitensity value on the LHR cards as a starting point?
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 06:05:43 PM |
|
Any recommendation for a xitensity value on the LHR cards as a starting point?
If it fails to unlock at 1 reduce to -1, -2 etc. If it unlocks stable at 1 increase the number to 2, 3,4 to increase the speed. LHR cards are tricky, and takes a while to find the correct clock setting / LHR setting.
|
|
|
|
dle378
Copper Member
Newbie
Offline
Activity: 77
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 06:18:08 PM |
|
Any recommendation for a xitensity value on the LHR cards as a starting point?
If it fails to unlock at 1 reduce to -1, -2 etc. If it unlocks stable at 1 increase the number to 2, 3,4 to increase the speed. LHR cards are tricky, and takes a while to find the correct clock setting / LHR setting. I am trying that now. How long should I run each test before changing to the next value?
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 06:25:41 PM |
|
How long should I run each test before changing to the next value?
If if fails in a few seconds (20) you should try another value. If it unlocks in a few minutes, might be good enough. You get warnings in the window when the card enters LHR, mode, then the program will reset the lhr and this takes time and hurt the pool hashrate.
|
|
|
|
Dojo76
Newbie
Offline
Activity: 30
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 06:33:34 PM |
|
Can you suggest a kernel for full AMD rigs? It seems that autotune always select kernel 0.
It used to be higher. We tried to improve it, but it keeps coming back. The hiveon pool have 0% fee, so even with 0.5% rejected you should get more shares than on the other pools you listed. The hiveon pool is using the ETHPROXY protocol and different code in the miner than the 2miners and crazypool. Hiveon has a higher share per minute rate compared to other pools, it seems TBM is not able to run 100% stable at that quicker rhythm. Probably is not fully integrated with ETHPROXY protocol but rejected are possible with other miners too because of that difference, despite being very rare. Did you try to optimize the code to speed things up during mining? I suspect it goes kind of "out of sync" at times
|
|
|
|
|
Dojo76
Newbie
Offline
Activity: 30
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 07:00:57 PM |
|
Did you try to optimize the code to speed things up during mining? I suspect it goes kind of "out of sync" at times
The ethproxy protocol need the full hash sent to the pool, this is calculated with the CPU. I see that other miningsoftware have moved the cpu verification and submit code to it's own thread. This might help abit. TBMiner is not working good on low difficulty pools because of this. Understood. The higher the difficulty the best TBM can do, from my experience Hiveon is one of the pools with the lowest difficulty. You're in the right direction to 100% solve the issue but you have to rewrite the code for this pool and run a special kernel when hiveon is detected. Xintensity is 71 by default for this pool, I suppose is by design but does not look that fast from my tests, share ratio is still higher with lolminer
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 07:15:46 PM |
|
Xintensity is 71 by default for this pool, I suppose is by design but does not look that fast from my tests
Every miningpool have optimal defaults 6800xt / 6900xt seem to like --xintensity 595 But only on 2miners.com, miningpoolhub.com, nanopool, f2pool, and a few other pools. https://github.com/sp-hash/TeamBlackMiner/blob/main/FAQ.md
|
|
|
|
ekgd39
Newbie
Offline
Activity: 30
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 07:24:51 PM |
|
Did you try to optimize the code to speed things up during mining? I suspect it goes kind of "out of sync" at times
The ethproxy protocol need the full hash sent to the pool, this is calculated with the CPU. I see that other miningsoftware have moved the cpu verification and submit code to it's own thread. This might help abit. TBMiner is not working good on low difficulty pools because of this. my experience , in hive os 12x 3080 no lhr , the fastest core is 1 , 495.46 cuda 11.5 drivers give less performance than cuda 11.4 . You should do detailed tests in hive os and improve stability, some rigs keep getting errors while generating dag file. Manipulations with the kernel and pl do not give much change. I am attaching a screenshot of the 5 hour test. https://ibb.co/b1d27xF
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 07:29:28 PM |
|
If the dag fail to verify try -K 1 (--dagintensity 1). Did you try the v1.43 build yet? I have added 7 cuda kernels that could work better on lower TDP settings (power).
--kernel can now take a value from 0 to 15
But run it in autotune mode first and check the results
|
|
|
|
ekgd39
Newbie
Offline
Activity: 30
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 07:39:50 PM |
|
If the dag fail to verify try -K 1 (--dagintensity 1). Did you try the v1.43 build yet? I have added 7 cuda kernels that could work better on lower TDP settings (power).
--kernel can now take a value from 0 to 15
But run it in autotune mode first and check the results
I use dag intensity 1 , on all rigs in test , but on rigs with 12x3070 and 12x3060ti it is unstable , maby you must do it option maximum slowly for rtx 30xx series, or do option dag repair, like LoL miner . if you do this , I can test it on all my rigs , I have above 6 ghs. Then I posted result to the other user , I think it can help many people , who want use you miner .
|
|
|
|
Akyboy
Jr. Member
Offline
Activity: 90
Merit: 1
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 07:59:13 PM |
|
Hi Guys
I have 3070 cards and DAG verification is failing with Afterburner OC settings that iv been using for months. (CC -502, MC +1200 PL 46) If I reset AB to default, wait for verification to pass, and then apply my settings all will work fine.
Also, I have tried multiple ways to connect to SSL flexpool but it's not working for me.
Help would be appreciated.
Thanks
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 08:05:50 PM |
|
Did you try v1.43?
|
|
|
|
Akyboy
Jr. Member
Offline
Activity: 90
Merit: 1
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 08:10:52 PM |
|
Did you try v1.43?
I suppose the question was for me? ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) I am on the latest version, just downloaded it
|
|
|
|
sp_ (OP)
Legendary
Offline
Activity: 2926
Merit: 1087
Team Black developer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 08:12:43 PM |
|
Did you try v1.43?
I suppose the question was for me? ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) I am on the latest version, just downloaded it and --dagintensity 1 doesn't work?
|
|
|
|
Akyboy
Jr. Member
Offline
Activity: 90
Merit: 1
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
January 21, 2022, 08:20:09 PM Last edit: January 21, 2022, 10:46:42 PM by Mr. Big |
|
Did you try v1.43?
I suppose the question was for me? ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) I am on the latest version, just downloaded it and --dagintensity 1 doesn't work? Nope,.. tried again. It exits.
And if you can please help me connect to SSL / 5555 on flex pool --hostname eth-us-east.flexpool.io --port 4444
|
|
|
|
|
|