ANTMINER S5: 1155GH(+OverClock Potential), In Stock $0.319/GH & 0.51W/GH

[marvykkio]

I reversed the blades and now it works, but the problem that remains in the blade where it goes attacked the controller remains burnt, so I should have a new blade guess right? but the thing that I do not admit is that I have to pay as well the Italian customs to get back garanzia.basta write a piece in the declaration hardware parts replaced under warranty because the product has already been paid previously

marvykkio, can you show us a picture of the burnt attachment point? Is it on the data cable, the PCIE power cable, or the power cable for the control board (that's the small 4 pin cable that's only attached to one hashboard)?

now and reassembled, and the small 4-pin connector that goes from the blade hashboard

[Tupsu]

I reversed the blades and now it works, but the problem that remains in the blade where it goes attacked the controller remains burnt, so I should have a new blade guess right? but the thing that I do not admit is that I have to pay as well the Italian customs to get back garanzia.basta write a piece in the declaration hardware parts replaced under warranty because the product has already been paid previously

I got my parts with DPD direct From China . No VAT.

artic mx-4 and not exceeding mx-2?

MX-4 is more expensive than the MX-2

now and reassembled, and the small 4-pin connector that goes from the blade hashboard

This is the controller's power cord.

[marvykkio]

now show you pictures

[jtoomim]

now and reassembled, and the small 4-pin connector that goes from the blade hashboard

My guess is that a metal object hit the controller board, causing a temporary short circuit between two exposed pins on the controller board (or on the Beaglebone Black). This would have pulled a large pulse of current through that small 4-pin cable, causing it to get scorched. Do you have a cat?

[marvykkio]

no no cat, my system and put it down in the cellar

[marvykkio]

I'm buying the thermal paste arctic mx-4, 20 grams, can be enough to change in 4x antminer s5? I want to change it in all the miners

[marvykkio]

[marvykkio]

well I think that there is nothing else to do, just send in the warranty miner, the problem and resubmitted

[marvykkio]

I was told that for s5 overclocking voids the warranty, my miner was 375m.

sorry if the question will void your warranty because putting this function?

[Tupsu]

I was told that for s5 overclocking voids the warranty, my miner was ..........

sorry if the question will void your warranty because putting this function?

Yes. However, you can erase your pictures and change posts.

[marvykkio]

now the picture is already been sent to the guarantee, I can not do anything anyway, and both seem to me bullshit

[marvykkio]

the problem is not the 25M more overclocking, and because it was defective factory, if you do not want to change it, do not buy more from bitmain, why and asurdo not change the product purchased from 1 week ago
and I only used psu good, 1 x 1 psu miner, RM1000 CORSAIR GOLD

[hanti]

why did u even try to oc it if it was broken....

[marvykkio]

I DID TO ENTER A GUY WITH BITMAIN TEAMVIEWER IN MY PC, AND HAS DONE ALL THE TESTS ALSO BRING TO DEFOUTL, BUT THERE WAS NOTHING TO DO AFTER TOLD ME THAT CAN NOT TELL ME NOTHING FOR ADSSO AND RECEIVE NEWS TO EMAIL, I ALREADY KNOW THAT I DO NOT WILL CHANGE THE MINER. GENTLEMEN DO NOT KNOW MORE SAY, WE HOPE THAT I CHANGE THE SECOND PART WHY ME WAS DEFECTIVE FACTORY, EVEN 10 DAYS ALREADY HAS MERGED A KNIFE, MANY PEOPLE COMPLAIN OF S5, CONSUMPTION, NOISE, AND DEFECTS.

[Tupsu]

I DID TO ENTER A GUY WITH BITMAIN TEAMVIEWER IN MY PC, AND HAS DONE ALL THE TESTS ALSO BRING TO DEFOUTL, BUT THERE WAS NOTHING TO DO AFTER TOLD ME THAT CAN NOT TELL ME NOTHING FOR ADSSO AND RECEIVE NEWS TO EMAIL, I ALREADY KNOW THAT I DO NOT WILL CHANGE THE MINER. GENTLEMEN DO NOT KNOW MORE SAY, WE HOPE THAT I CHANGE THE SECOND PART WHY ME WAS DEFECTIVE FACTORY, EVEN 10 DAYS ALREADY HAS MERGED A KNIFE, MANY PEOPLE COMPLAIN OF S5, CONSUMPTION, NOISE, AND DEFECTS.

Cries will not help here.
I'm happy with my 40 TH/s  Antminer S5.  The best miner at the moment.

[marvykkio]

I apologize for the caps lock

[marvykkio]

but my fear and I did not replace the blades, also because I bought with pleasure from them, and I trust, however, can not tell me that the problem and because they found the frequency to 375m, when the defoult and 350M, I do not think that this is the fault 25M more? by I noticed that when I move the connectors 6 pin pci the blade back to work, but after a while back as before and I have to go back to touch the connector, and a lack of solder connectors

[MyRig]

@marvykkio,

Your case is reviewed by Bitmain USA now.  Please wait for a few days. Bitmain_D will look into your Hashing PCB problem further.  Please check your e-mail for further instruction!

[marvykkio]

hi we are happy that you're here, you've seen in the photo and shared? this happens as I move the connectors 6 pin pci, through no fault of overclocking as I have written,

[marvykkio]

nothing to do and the problem came back, expect are felt