I have a rig of RX470's that do ~27. When I heard about these RX570's doing 29+, I went ahead and got one (or eight) and put one into my rig after some tweaking... 470 4G can do 29+ too ...
|
|
|
i would like to read data from json format somebody can explain this value: (unknow)
{"result": ["9.3 - ETH", "21", "182724;51;0", "30502;30457;30297;30481;30479;30505", "0;0;0", "off;off;off;off;off;off", "53;71;57;67;61;72;55;70;59;71;61;70", "eth-eu1.nanopool.org:9999", "0;0;0;0"]} 9.3 version 21 ? unknow Running since 21mn 182724 hashrate, share, reject 30502 hashrate for gpus 0;0;0 unknow Shares for DCR, SC, PASC, ... off;oof unknow Hashrate for DCR, SC, PASC, ... 53,71 temp/fan % eth-eu miningpool 0;0;0;0 unknow
|
|
|
Hi, I really appreciate the feedback. Could you please elaborate what I should do with the link? Are these some BIOS parameters that I should edit with a HEX editor or something? copy whatever original strap you want to mod.. like 1500, 1625, or 1750 from your bios and paste it into the link over the strap thats in the link. the output will be the modded strap and should have higher mhs. I did not make the tool Can't we just get strap from a 470 Armor OC an copy to 570 Armor OC ? And what about flashing 570 with a 470 bios ? Thanks
|
|
|
We now know we can flash 4xx with 5xx bios. But can we flash 5xx with 4xx bios ? ( to stay with "old" drivers and don't have driver bios signature problem )
Anyone ?
|
|
|
We now know we can flash 4xx with 5xx bios. But can we flash 5xx with 4xx bios ? ( to stay with "old" drivers and don't have driver bios signature problem )
|
|
|
Hi Claymore, RX580 8G is not working good in stock just giving 22-23 Mh. Is it because your miner does not support this card yet?
Like all others RX @stock
|
|
|
which rx470 and rx480 driver version I have to use with modded bios ?
16.11.5 Are you sure about this? According to the first post it should be 15.12? Or is this for non modded cards It's impossible that RX are in 2015 drivers I think. And yes, 16.11.5 don't have bios signature check, so they work with modded bios.
|
|
|
Hi, i'm testing this. Is there any api or service we can use to control rigs and switch mining on the fly ? Thanks
|
|
|
hello,
please how can i use claymore on coinmine.pl ?
By reading the readme.txt or the first post ?
|
|
|
Does anyone know what causes the "GPU #0 returns incorrect data" warning ?
In my case, was memory OC too high.
|
|
|
Make sure to lower the mem voltage (actually is mem controller voltage) to as low as you want your core voltage.. so like put them both at 900mv or whichever value you want
How works voltage on RX ? Testing differents values with 4*470. 980mV core and 980mV mem. Give ~850w at wall 950mV core and 980mV mem. No change, give ~850w at wall 950mV core and 950mV mem. Give ~790w at wall ! I can't believe put -30mV on mem give -60w at wall !
|
|
|
My seasonic 750w gold kept up for the last week dual mining gpu-z showing 110w for each card. Now they are undervolted. You mean this is not good for longterm? Mind you i have 4 cards not 6. Well ive been mining for a week with old settings dual mining gpu-z showing 110w for each card no problem. How will you explain this? They are even undervolted now.
gpuz power in not the same as wall power ! i've : 4*470 on ETH only, ~1075/1900 980mv , 750w at wall 4*470 on ETH+DCR, ~1150/2000 980mv, 850w at wall ( dcri 25 with v9.0, was 35 with v8.1 )
|
|
|
Did no Change to my ETH speed but doubled my DCR speed without affecting Power consumption. At least for what GPU-Z used to show in 8.1 and now.
I am getting 29.8 eth and 717 DCR per card with Sapphire Rx470 4GB Nitro with Samsung Ram. Bios is modded from 1750 to 2k straps.
Ram is overclocked to 2100mhz with 930mV. Core is 1150mhz with 900mV. Power consumption is around 92.5w in GPU-Z. I don't have a kill a watt so i don't know what the system or a single card really pulls from the wall. There are not many fluctiations in GPU-Z Load or ETH speeds. Only some from gpu and no voltage or default walues seem to fixed. It is so rare. I am using 17.2. drivers. Wonder if i can downvolt even more but wont try because my numbers seem good. Have 4 of these cards in the rig. Running it with a Seasonic 750w Gold psu.
750w is short for 4 470 on dual !
|
|
|
Tested on 4 470 4G Armor OC v8.1 dcri 35 = 111-112 ETH + 1950DCR, ~850w v9.0 dcri 35 = 94ETH + 3250DCR, ~850w v9.0 dcri 30 = 101ETH + 3025DCR, ~850w v9.0 dcri 25 = 106ETH + 2650DCR, ~850w v9.0 dcri 20 = 106ETH + 2025DCR, ~800w v9.0 dcri 15 = 103ETH + 1560DCR, ~750w
|
|
|
Does anyone have an experience with 1 fan variants of cards for mining? (XFX, PowerColor). Do they run a lot hotter than others because of the 1 fan, or is it okay? Also the MSI Armor RX470's, how's their cooling? I've heard that they run hot because they only have 2 heat pipes, but I don't have one to confirm. I have an RX480 Armor with 3 heat pipes and it runs fine.
470 Armor OC 4G have 2 heatpipes 480 Armor OC 4G have 3 heatpipes
|
|
|
Hi,
Running windows 10 Biostar TB85 Having 5 x Nitro+ RX 480 8Gb
But one card is running only 4.222 Mh/s, can someone please help and teach me to fix the problem? Please advice.
Best Regards
You need to connect screen or hdmi to vga converter on this card.
|
|
|
Error 404 on GUI Windows Wallet files !
|
|
|
wtm calculates nethash from difficulty. Its always an estimate (even for a wallet), but I have to admit the difference is big here. Personally I think this algo needs a better retarget logic. The base block_time should be 5 mins, while we are mostly hovering between 3-4
Edit: Delisting pasl for now, tomorrow will switch it to calculate difficulty from nethash given by wallet (reverse logic, but it seems to work for pasc)
Thanks for your works
|
|
|
There is a 4* ratio between wallet and whattomine
|
|
|
|