All of my Ants are operating at 300Mhz and using about 200-220W at the wall. I like only needing one CX750M for two ants!
|
|
|
There will eventually come a time when an ASIC (miner) cannot be manufactured for less than it should sell for to be profitable (for the buyer). At this time hardware makers will stop selling hardware. They might still make miners, but will probably mine with inventory themselves at a location that has cheap or free power. Eventually only people with free power will still mine for profit, and that profit will be very slim.
|
|
|
Check the temps, does one blade show 127C?. I received an S1 that did that and it turned out to be a bad temp sensor. The sensor is located right in the middle of the blade. It is an 8-pin device that has "LM75" on top. After I replaced the sensor, the fan(s) behaved normally. Hope this helps!
|
|
|
It could be heat related. What temps is that unit showing. Also, if you have a multimeter, take it with you and check the 12V input to that blade.
Usually, deactivated chips means high temps or low voltage.
|
|
|
To anyone, thanks in advance. Is there a way NOT to take Dogecoin but to accept Litecoin. Really do not want to be paid in Dogecoin.
I just enabled local payments and now I HAVE to accept Dogecoin.
|
|
|
Can I purchase the 17board kit from your website and pay you with bitcoin? Thanks! Edit: Just purchased a 17 board kit from http://minersource.net/Hope to receive it soon!
|
|
|
I am logged into my account and see nothing pertaining to providers. All of the tabs are for renters. I need to change some settings with one of my rigs but cannot access them. I logged in using my E-mail. Halp! Log out and log back in I tried this. Still only have renter tabs/info. Here are the tabs I see: my rigs/pools/bulk management/btc/ltc/doge/orders/history/2fa/password/referrals ? The top menu has a provider button for you now. There is a menu above the logo and a menu below. Found it! Thanks!
|
|
|
I am logged into my account and see nothing pertaining to providers. All of the tabs are for renters. I need to change some settings with one of my rigs but cannot access them. I logged in using my E-mail. Halp! Log out and log back in I tried this. Still only have renter tabs/info. Here are the tabs I see: my rigs/pools/bulk management/btc/ltc/doge/orders/history/2fa/password/referrals
|
|
|
I am logged into my account and see nothing pertaining to providers. All of the tabs are for renters. I need to change some settings with one of my rigs but cannot access them. I logged in using my E-mail. Halp!
|
|
|
Hi guys, what values should I use so I can safely power 2 ants with a 750W PSU? I have so many PSUs I don't want to buy more Could I do something like 160 GH for 250W? Sounds about right. I have two Ants per CX750M and run mine at 300Mhz. I also undervolt to about .90-.95V. This results in about 220W of power draw per Ant. They hash at about 153Gh. I would imagine 325Mhz would result in close to what you want, power wise. I calculate 8x325=2600Mhs x 64 =166400Mhs, so 166Gh and about 250W. I run mine at 300Mhz because it seems like the best tradeoff between power use and hashrate. The temps went down quite a bit too Vs. stock speeds.
|
|
|
Anyone else having trouble with LRP connecting to eligius? I have it set to port 12234 but have recently been getting messages indicating it can't connect.
Is LRP due for an update?
Anyone? Also port 12234 on this pool no longer works. Port 3334, constant disconnect/reconnect. Edit: LRP working now. Any idea what the issue was? Still not working. Maybe a problem with Eligius. My ants are disabled for now. Does your username have special symbols? It has an underscore. But I can try a username without one.
|
|
|
Obviously S1 will become obsolete this year. I have 27 in a custom shed built. Ambient temperature with the ac fluctuates between 70-85F. The S1's themselves run from 45-59c depending on how hot it is outside. Those numbers should be okay for the short life span these Ants are expected to have yes?
Just downclock. I run units @300Mhz and .90V. They pull about 200W at the wall connected to a Corsair CX750M (80 bronze). They hash at 151Gh. I used to overclock, but the gains just didn't seem worth all the extra power supplies/heat/instability/noise/power use. Check out what this dude is doing: https://bitcointalk.org/index.php?topic=526060.0
|
|
|
Anyone else having trouble with LRP connecting to eligius? I have it set to port 12234 but have recently been getting messages indicating it can't connect.
Is LRP due for an update?
Anyone? Also port 12234 on this pool no longer works. Port 3334, constant disconnect/reconnect. Edit: LRP working now. Any idea what the issue was? Still not working. Maybe a problem with Eligius. My ants are disabled for now.
|
|
|
Where are you located? Would you be willing to use escrow? Would you sell just two of them to one person?
Thanks!
|
|
|
Anyone else having trouble with LRP connecting to eligius? I have it set to port 12234 but have recently been getting messages indicating it can't connect.
Is LRP due for an update?
Anyone? Also port 12234 on this pool no longer works. Port 3334, constant disconnect/reconnect. Edit: LRP working now.
|
|
|
Is port 12234 no longer available? I have been using it for Leaserig.net for some time and last night I could no longer connect to it. Now port 3334
works for leaserig. Any thoughts?
|
|
|
Anyone else having trouble with LRP connecting to eligius? I have it set to port 12234 but have recently be getting messages indicating it can't connect.
Is LRP due for an update?
|
|
|
Have these been sold? I am still interested.
|
|
|
Looks good. Kinda like the numbers I put together. I lease some of my ants out which helps close the gap. Sometimes you can mine alts and sell at really good returns vs. Bitcoin. Underclocking to reduce power usage helps too.
|
|
|
I have 90+ erupters. Put them back in the boxes. Give me a fair price and they are yours.
|
|
|
|