|
Using for years without issue two PSU setup connection marked at Your drawings as "not correct". My opinion is opposite, of course:
- I know for sure that there is no power connection between motherboard and riser. Therefore I can freely use different PSUs for motherboard and GPUs.
- I don't know for sure is there power connection in GPU between it's PCI-e slot and PCI-e power connectors. So I don't mix PSUs to power riser and power connectors on single GPU.
|
|
|
|
$2499.99
100Gh/s mining speed
Delivery June 2018
Too round numbers. No go. |
|
|
|
Since RX460 cards become more popular, I will add ASM mode for these cards in next update along with some other improvements, it will be available in 2-4 days.
RX560? |
|
|
|
No, You've been extremely unlucky with consecutive non-deliveries. Anyhow, purchase from Aliexpress is more secure than from any online market, because if You don't receive items You get Your money back and fake seller gets nothing. And don't forget to use link in my signature to register and get at least 6% cashback from Aliexpress. Profit.  EDIT: Hint: use HongKong Air mail for shipping if available - it reaches EU in 7-10 days.  |
|
|
|
problem here..
I have rig with 2x RX 470 and I got one RX 460.. problem is that I only get about 2000 mh/s with RX 460, while RX 470 (moded BIOS, OC) giving me normal hashrate (28 mh/s)...
where did I go wrong?
RX 470 are connected with risers, RX 460 is plugged directly to MOBO...
Connect monitor to GPU with low hashrate. |
|
|
|
Hello everyone. I have a problem with one of my rigs. I get the ""WATCHDOG: GPU 0 hangs in OpenCL call, exit" problem after about 20-60 min running the claymore miner. It started tough with that my miner was loosing internet connection after running a while. When i fixed that by installing new network adapter drivers, the connection was stable but the GPU´s started to give 0.00 mh´s after a while, until getting the error message. I did overclock the rig in the beggining, but i have reseted the MSI afterburner settings to default and i also did a bios mod, but i flashed the cards back to the original bios. I also dont think that the bios mod was the problem, because i have 3 more rigs with rx 470 with the same mod, and they all work great. Specs: Intel Celeron G1840 Processor Asrock H81 Pro BTC motherboard 6x AMD Radeon RX 470 4GB 4GB DDR3 Memory 60GB SDD Harddisk 1000W Gold power supply Windows 10 operating system
I have already tried to:- Run the miner with the gser and eser commands and have also tried both dual and solo mining(both have same problems). - fresh install of both operating system and Gpu drivers (first gpu drivers with DDU and after that operating system). - Checked every riser, but they all work on a diffrent system so thats not the problem. - Setting virtual memory to atleast 16000 - Tried old claymore miners, from 6.3 and up, same problem. I dont really know what to do at this point, would really appreciate help if someone knows what might be causing this.  I believe with 60GB drive You don't have 20 GB virtual memory, right? |
|
|
|
Hello, I was mining DGB on my pc and everything was fine, but I decided to install Crimson 15.12 driver and now the miner doesn't send any share to pool. http://imgur.com/a/K86jYScreenshot http://imgur.com/a/K86jYI noticed that WU is 0.000/m all time, It was on 0.05 before. I'm using an AMD Radeon R7 Series How I can fix it? roll back driver |
|
|
|
https://youtu.be/aAdW0wdUmosMy Fury rig on Claymore 12.5 with 15.12 drivers + (ASM activated) 846W for 6 cards. Let's round to 790W to remove CPU/Mobo/RAM Now remove PSU efficiency (8% for my platinium) 732W / 6 = 122W per card for 400-430 H/s cclock/mclock/powlim? |
|
|
|
I was mining DGB on my pc using sgminer 5.6.1 and everything was fine, but I decided to install Crimson 15.12 driver and now the miner doesn't send any share to pool. http://imgur.com/a/K86jYScreenshot http://imgur.com/a/K86jYI noticed that WU is 0.000/m all time, It was on 0.05 before. I'm using an AMD Radeon R7 Series How I can fix it? I assume You can roll back driver in Device Manager/properties of gpus... |
|
|
|
Trying to find the solution to GPU1 not working. Can anyone help?
Notice GPU1 on the top right (Hardware Monitor)
I see You've been so lazy to connect display at card hashing with 4 MH/s as I told You. Let's try the finger exercise, hope it is not too much for You again: 1. Stop the miner 2. Open device manager 3. Disable GPU that was hashing with 4 MH/s 4. Enable GPU 5. Start the miner Claymore, please make this be done automagically by the miner. Thx. |
|
|
|
I tried it but, the core clock was not low. Any Other Solutions/Experiences?
Your GPU is not in "not started" mode, but it's in common known "4MH/s" nirvana. If You are near by, power off, connect monitor or HDMI dummy plug into "stoned" GPU and than power on. |
|
|
|
Hello every one,
I have an odd behavior from dual mining
W10 pro
claymore 9.3
4xRX470 with 1500 straps
if I mine ETh only, everything is normal, after memory overclock, I'm 29Mh/s.
The probleme is, if I dual mine (DCR or SIA), my ETH hashrate is going super low. The only way to not loose too much hashrate is to choose DCRI 1 or 2 but in this case, it's almoste useless to dualmine.
And my memory overclock boosted the hashrate well in single mining but not in dual mining. +100 Mhz on memory? same result in dual mod, +10% in single mode.
I can see the monitoring showing that the GPU is almost always below 1 000 Mhz, even at super low dcri, at 10 dcri, it stays around 850 Mhz in dual ETH SIA.
In ETH only mode, it is higher than 1100Mhz. My GPU are even hotter in single mining than dual!!!
It was the same thing at stock clock/bios. When I was just testing, I lost 30% of my ETH hashrate when I tried dualmining on DCR (using the super basics configs that was as exemples in the readme.txt, I even didn't change the wallet adressses...)
I do use the GPU_FORCE_64BIT_PTR 0 and others.
Does someone have an idea?
thx folks
-powlim is the switch for Your dualmining success. Of course You should have some power supply reserve to increase power limit at values of 20, 30 or more. Try first with values like 5 and see if it improves the speed. Increase in steps of 5, but when You reach 20 and need more, first check do You have to change max power limit value in Your GPU BIOS. |
|
|
|
Hi everyone, I'm planning to order the first equipment for my test-rig. What do you guys think of this setup:  The costs of the risers, SSD, Motherboard, CPU, DDR and Power Switch are $149.94. I'm not sure about my PSU yet, I'd probably need a 1000W PSU for a 6GPU rig. The GPU's are incoming, but the price is not set jet. Probably around USD 200/GPU. Please let me know if I forgot anything, any feedback is highly appreciated! Best regards, Maartentjewut You can start instant saving from 7 up to 10% if You register for AliExpress cashback program in my signature. |
|
|
|
What ideas do you guys have for hosting solutions?
Also wasn't there a forum member that was hosting for multiple other forum members? Feel welcome to PM me if you want to keep anything private. I'm looking for a hosting solution
sidehack is offering hosting solution with acceptable power price and VPN access. He's from time to time overwhelmed with other design/production priorities, but keeps hosting pace in general. |
|
|
|
Never, remember never to update the driver and go to sleep! I updated, went to bed, and one video card burned: D
Sorry for the loss, but this is better situation than burning in front of Your wide open eyes... |
|
|
|
Will the last one cost 100.000$? Asking for a friend... |
|
|
|
This is link for controller (Orange PI) image. Links for device FIRMWARE noted in user manual are not working. |
|
|
|
This scamming scheme becomes boring... Newbie account asking questions about links.  |
|
|
|
|
I believe You have by mistake one leading zero more than real price.
|
|
|
|
|
Show Posts
