Show Posts
|
Pages: [1] 2 3 4 5 6 7
|
5
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v9.8 (Windows/Linux)
|
on: August 26, 2017, 03:10:53 AM
|
Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?
remove the overclock setting in the claymore bat file. using AB to adjust no Oc settings,just basic solo mining command did you tried the aug-11
|
|
|
6
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v9.8 (Windows/Linux)
|
on: August 26, 2017, 01:35:57 AM
|
Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?
remove the overclock setting in the claymore bat file. using AB to adjust
|
|
|
7
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: 1080Ti Specific - Best mining option
|
on: August 24, 2017, 02:26:15 AM
|
MSI Z270A-Pro G3950 CPU 2x4GB RAM 6xEVGA 1080Ti OC Edition 1xEVGA SuperNova 1200 P2 6x V.007 Risers
Cards synced in Afterburner and set to 65% power, + 150 Core, +600 Memory
Win 10, latest BIOS from MSI, latest driver from nVidia, NiceHash Legacy 1.8.1.1
Been running rock solid since turning it up a couple of weeks ago. Pulls right around 1,100W at the wall @ 247V.
my ftw3 can only boost +130 stable Don't worry, it's a silicone lottery for everyone. We have 1080 Ti GPUS that will do +225 and others that can only manage +125 The silicone lottery for me isn't my EVGA's doing +150 Core at 65% power, but my Zotac Articstorm doing +250 @ 70% power. It averages about 780 Sol/s.   I think it would probably do over 800 Sol's if I give it more power. did you using the water cooler?
|
|
|
9
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: 1080Ti Specific - Best mining option
|
on: August 23, 2017, 03:30:36 PM
|
MSI Z270A-Pro G3950 CPU 2x4GB RAM 6xEVGA 1080Ti OC Edition 1xEVGA SuperNova 1200 P2 6x V.007 Risers
Cards synced in Afterburner and set to 65% power, + 150 Core, +600 Memory
Win 10, latest BIOS from MSI, latest driver from nVidia, NiceHash Legacy 1.8.1.1
Been running rock solid since turning it up a couple of weeks ago. Pulls right around 1,100W at the wall @ 247V.
my ftw3 can only boost +130 stable
|
|
|
10
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: 1080Ti Specific - Best mining option
|
on: August 23, 2017, 03:28:45 PM
|
Hardware: MSI Z270A-Pro 4 GB Ram 2TB HDD G4400 CPU 1x 750W B+ PSU 1x 850 W B+ EVGA PSU 3x MSI Gaming X 1x Zotac Amp Extreme Core 1x Asus ROG Strix 5x Powered Risers Software: -Clean, activated Win10 -All updates from Win update -Latest drivers form MSI website (chipset) -Latest Nvidia drivers -Latest ccminer from Tpruvot - MSI Afterburner (to limit cards powerdraw) The algo I was trying was bitcore and skein. I've limited TDP to 75% in MA, so I've assumed that it'll have enough power. Do someone have Zotac and can share how much these beast draw at 75% tdp? My config for psu's. Weaker PSU got two cards (MSI), their risers, mobo, cpu and hdd. It's working fine (that config was working before). Now I want another psu (850W) to power 3 cards and their risers. And it's kind working. But not for mining  PSU 1250W with 5 evga ftw3 1080ti 70% tdp WORKING FINE
|
|
|
12
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: AMD Releases Driver for DAG Issue !!!
|
on: August 21, 2017, 01:13:06 AM
|
The official AMD blockchain driver for windows 7 x64 does not work (miners crash). The leaked driver from robinh00d works but nothing can undervolt my RX570's, only OverdriveNTool works for a few seconds before reverting.
The solution that worked best is to use the leaked driver and the wattman from the official driver:
1. Install the official amd driver with amd settings 2. Without reboot install the leaked driver via device manager by going the "i have a disk" route (for all cards - one by one) 3. If you have a modified bios, run atikmdag-patcher and reboot 4. Use wattman to apply your mem clock and volt settings 5. Open miner, everything will be ok except undervolt, now with miner running make a small change to wattman and reapply (for each card one by one)
The voltages appear to be sticking for as long as the miner is running , except for the main card that reverts occasionally.
everything is works now. except the power with eth+SC almost sucks 140W.
|
|
|
14
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: AMD Releases Driver for DAG Issue !!!
|
on: August 20, 2017, 12:41:23 AM
|
As far as i know this driver does not work on Win 7.
It does work on Win 10 for RX580's. Just dont patch the driver with pixel patcher on 580's. I used AB 4.4.0 Beta 16, works for OC settings. It however does not seem to undervolt card. Also do not set your OC settings in the Claymore Batch file. does not work. The Driver changed the ADL API so would need an update for Claymore to fix this. I used Global Wattman that comes with driver. Manually setting Voltage to 990mV and apply, it applies it but sometimes just reverts back to higher voltage later. Just set it back to Auto and apply then my voltage goes to 990mV again. (i do this while claymore is running) Not even AMD software is properly controlling the Voltage..... tisk tisk AMD! When you apply the pixel patcher and OC from the claymore batch file you get your mem clock jumping between 2150 and 1000MHz the whole time. EVen GPU-z is reading GPU load incorrectly at 16% and mem controller 100% when it should be idle. HWinfo64 seems to read the GPU load correctly.
Managed to get my card stable at 30.5MH/s (MSI RX580 Armor 8GB) 990mV, 1250 GPU core, 2150 Mem clocks. Drawing under 100W running at 59-61C Temps. Happy will settle for that. If running other AMD cards in the machine, and settings dont apply to others it could be because the are running headless. Might need to plug in a dummy plug into cards to make it think it has monitor connected. i know this works. Have found this with Nvidia mixed with AMD machines. All Nvidia no problem.
AMD wont update driver again, so Claymore will hopefully soon update to fix OC and undervolt issues directly from the Miner batch file.
thanks
|
|
|
15
|
Alternate cryptocurrencies / Mining (Altcoins) / Re: AMD Releases Driver for DAG Issue !!!
|
on: August 19, 2017, 03:05:40 PM
|
Hi, I have been running my rig with 4x powercolor rx 580 8gb, 2x rx 570 4gb and 1 sapphire rx 580 nitro + 8gb
after updating to this blockchain driver one of powercolor rx 580 card started to heat up very much. +5 degrees than others. I tried to run only with this card. same heat. reverted back to previous driver but heat still goes up to 75+ degrees. 4 cards are identical and only one of them causing this issue.
What do you guys think might cause the problem?
one of my rx580 hung . even i tried to install the old driver.
|
|
|
|