haha just realized I joined you guys a couple minutes ago   Have to get the miner workin on Linux.  Might take me a few min.

ahhh, ok thanks

All my shares are getting rejected at any pool i use, why

The coin came out 4 days ago 

Why do i keep getting rejected shares when i try to mine this coin

is this not scrypt?

I actually like this idea too.  That is a very good idea. I'd be on board for that for sure

I'm holding all mine.  I think most who are serious about the coin are holding.  It took all day yesterday to get an order of mine for 2 million filled. Lots and lots of little trades it seemed like, I think from the multipools guys.

btw, about the lowering of the block reward thing I mentioned last week, hope I didn't cause any controversy on the coin.  Whatever you guys think is best.  The gravity thing to help against multipools sounds like a cool idea.

And for the rest of us who have been here and reading.  I think it's safe to say the Dev's have proved themselves that they care for this coin long term, turning down on option for large short term gain in favor of long term goals and success.  That should make everyone feel comfortable.  

One thing that I have noticed with this coin compared to many that I have seen in the past, is nearly everyone here involved in our digibyte community appears to have a level head on their shoulders and are professional and wise.  That says something.  A lot of something.

Most cpu coins can be mined with gpu's now.  unless there is something new I'm not aware of.

I wonder what gpu temps will be in a 4u case like that

so what is the verdict on these miners?  any good?  worth it?

Try;

--lookup-gap 2 -I 13 --thread-concurrency 11200 -g 2 -w 256 --gpu-engine 1050 --gpu-memclock 1500 --temp-cutoff 90 --temp-overheat 85 --gpu-fan 90

go in the cgminer folder and delete the scrypt-tahiti.bin files first and whenever you change thread concurrency.  

I remove the vector tag as it slows me down "-v 1".  

Undervolt in the VBE7 with 1100 to 1110 and remove "powertune -20" from the cgminer bat file and just leave it at default which is 0.  Also make sure overdrive is turned off in catalyst control center.

Open a terminal window and type;

setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1

I get 740's+ with this setting and my cards run in the 60's in open air rigs.  1080/1500 will get you 765+ but you'll usually have to volt higher. Other sweet spots are 1020/1500, 1030/1500, and some people report success with thread concurrency 10240, or sometimes using --shaders 2048 instead of thread concurrency.  If you push the memory above 1600-1675 your system will start to crash and you'll have to overvolt the memory which you don't want to do.

Scrypt settings are voodoo.  One number in either direction can cause hashrate to drop significantly.  The trick is finding the magic numbers.

Using a pc case though will cause the cards to run pretty hot.

Yes very good.  VBE7 and cryptobadger's guide is the way to go for sure.  The regular software programs always aren't reliable for correct and consistent voltage adjustments.  For my Sapphire 280x OC's I used VBE7 and set both #5 and #6 options to 1100 for voltage, which ends up showing as 1.019 in the operating system.  The power saving is pretty good, but the heat and temp difference for the cards is significant.  If you let it run for a day without and then change it the next, you'll see.    Mine are rock solid stable using 1100.  But you can always bump a bit higher if you feel like, or if you need to, say 1110.  The exact numbers don't matter as in "1137", etc, as long as it's close.  To maximize hashrate you can just change the clock settings while you're in there too.  Usually 1050 clock and 1500 memory I've found best for mine.  But some people use 1030/1500. 1080/1500 gets slighter higher hashes but usually requires more voltage.  Also memory voltage use 1500.

Also don't forget to flick the bios switch on the cards before flashing. 

Glad to help, and welcome to DigiByte  

I have a bunch undervolted.  Are you using VBE7 or software? 

Is this for real?  I thought you were joking, but there is a whole write up.   

I would put the arctic fans at max yes considering the low rpm

This is indeed very awesome. 

hilarious

The pool advertising is ridiculous

Screwdriver
or HDD jumper
or $2 switches on amazon from china