As a batch 1 BJ customer that received my order (but no MPP) and am awaiting two BJ upgrade kits, what should I do to hope for the highest chance of getting something back? I know the amounts owed to me would be not enough to make the list.
|
|
|
S2 received yesterday after ordering it on Friday evening. The boards inside were all jiggled loose during shipment and the case itself was a little bent but everything works fine. I wonder if Bitmain could consider shipping the boards secured together seperate from the case itself so there is less chance of damage from the boards clashing around in the case.
Everything works though after plugging them back in.
|
|
|
I have 1 S1 coupon to donate. First PM gets it.
|
|
|
Just emailed Gallo's firm with my information and was wondering if he has been good to work with so far? The retainer of 40% plus fees seems like there really won't be anything left for us in the end.
|
|
|
I think I figured out why my BJ stopped hashing all of a sudden. Anyone know how I should go about replacing it? Secondly, if not, does anyone know how to jumpstart the 1000XP psu? I'm interested in at least using it to power some antminers but putting a paper clip in the typical holes on the 24 pin socket (where the green/black wire goes) doesn't work.
|
|
|
This is the error I'm getting with my Babyjet now after hashing away since February. [P]ool management [S]ettings [D]isplay options [Q]uit HFA 0: 55C/.80V 52C/.82V 50C/.82V 51C/.81V ZOMBIE/ 0.000h/s | A:0 R:0 HW:0 WU:0.0/m --------------------------------------------------------------------------------
[2014-05-13 20:16:46] Probing for an alive pool [2014-05-13 20:16:48] Pool 0 difficulty changed to 4 [2014-05-13 20:16:48] Pool 0 difficulty changed to 256 [2014-05-13 20:16:48] Network diff set to 8.85G [2014-05-13 20:16:48] Stratum from pool 0 requested work restart [2014-05-13 20:16:48] Rejected untracked stratum share from pool 0 [2014-05-13 20:16:48] Pool 1 difficulty changed to 2 [2014-05-13 20:16:50] HFA 0 HFHash usb write err:(-7) LIBUSB_ERROR_TIMEOUT [2014-05-13 20:16:50] HFA 0 HFGetHeader usb read err:(-4) LIBUSB_ERROR_NO_DEVIC E [2014-05-13 20:16:54] API running in IP access mode on port 4028 (14) [2014-05-13 20:18:14] HFA 0 attempted reset got err:(-5) LIBUSB_ERROR_NOT_FOUND [2014-05-13 20:18:14] HFA 0: hfa_send_frame: USB Send error, ret -5 amount 0 vs. tx_length 64 [2014-05-13 20:18:14] HFA0: send_packet: OP_USB_INIT USB Send error, ret -4 amount 0 vs. length 8 [2014-05-13 20:18:14] HFA 0: Failed to reset after write failure, disabling [2014-05-13 20:18:14] HFA 0 failure, disabling! [2014-05-13 20:18:14] HFA 0: hfa_send_frame: USB Send error, ret -4 amount 0 vs. tx_length 8
For flashing the firmware in Ubuntu, do I have to install any drivers to flash the package? I get the can't find command error when executing "sudo ./field_firmware_update.py" in the extracted folder
|
|
|
My babyjet keeps getting USB errors all of the sudden with rasp pi.
I tried to use a Ubuntu installation and run this command with the firmware:
sudo ./field_firmware_update.py
but it doesn't work. What's the process to manually update the firmware? Thanks.
|
|
|
I know this is off topic but i hope that hashfast reads this forum, i would just like to thank them for completely destroying what i had. so far i lost my business due to me investing into them and using my savings, lost my house due to losing my business and now having to stay at a friends house in order to pick up my life and start over. I have tried contacting them via phone and e-mail, but keep getting the same bs. this cant go on! their ruining lives!
How many Sierras did you buy to put you in that much debt and lose your business? Sorry for your loss too. I'm waiting for a few upgrade kits atm and lost a good amount as well.
|
|
|
Did anyone find the self updating rPI image not work for them? I plugged in the HDMI cable and the image boots up archlinux but then shuts down on its own despite having the BJ plugged in. No mention of any flashing of the firmware at all.
|
|
|
You're right. Thanks for the quick response. Everything looks normal again on the site too.
|
|
|
Just checking, is maintenance still on?
Under my account details, balance, unconfirmed and future are blank. My workers are registering properly though.
|
|
|
I wonder when bitmain will release their gen miners? This seems like a good for way to clear out their gen 1s.
|
|
|
Just wanted to see how complete B1 shipping is. Anyone else waiting for a B1 Babyjet?
|
|
|
Anyone still waiting for their order? I had 2 separate babyjet orders but only have received one so far. Of course no replies to emails or phone calls yet regarding status of the order.
|
|
|
Any information on how to set it up? Have one on the way but I can't get home for another week and will have to get my wife to get it up and hashing.
|
|
|
Are we able to get refunds on our upgrade kits?
|
|
|
Will you disclose if they give you a half-working Terraminer? j/k. Thanks for making the trip.
|
|
|
I think back then the non-custom hardware had much more GPU related discussions which are now obsolete. There doesn't seem to be a reason to split off ASICs into "custom hardware" anymore.
|
|
|
Are those computer cases there possibly baby jets in the making?
I had the same thought. But it looks like those are just computer cases. actually that makes sense. I'm sure they would show off the BJ cases like the Sierra case if they were available. Cmon show some pics of them already!
|
|
|
|