ASICMINER Auction: 50 Block Erupter Blades CHECK OP FOR PAYMENT

[lan787]

Mine seem to max out around 11.5GH each.. i checked the voltage and they're all at ~1.20-1.23V, clock setting: High

For the people that are seeing 13GH, have you done anything different or tweaked anything in your setup?

is that 13GH on the web blade web interface? or as reported by your pool?

The interface reports 13GH/s, the pool reports 12.5GH/s. I did no tweaking at all.

[desired_username]

mine works in the 11500-13500 range (web), and pool reports 10000-12500 so far

[Pinwheel]

When I restart a blade it takes approx 15mins to reach it's full speed (around 13ghs).

You could try running a local stratum proxy and see if it makes any difference?

I'm running a local stratum proxy.

Current Setup is blade at 192.168.1.20, proxy at 192.168.1.10, then to slush. I wasn't happy with the 6 gh/s attempts this morning, so I am trying to reconfigure the blade for bitminter. I'll report back later today with the approx speed after a few hours.

try to test it on mmpool.bitparking.com from all pools which I tested this one gives pretty accurate hash rate in short time.

[dogie]

Just my luck. One of my cards is well behaved, the other is a diva. Its convinced itself that its so fucking precious that it has an efficiency of 102%.

BAD GIRL.

[Omen1855]

Mine seem to max out around 11.5GH each.. i checked the voltage and they're all at ~1.20-1.23V, clock setting: High

For the people that are seeing 13GH, have you done anything different or tweaked anything in your setup?

is that 13GH on the web blade web interface? or as reported by your pool?

I also noticed a serious difference between slush pool results and bitminter with getwork. Former goes up to 13 GH/s the latter 3 GH/s, while bitminter does report 10 GH/s. So try with a stratum proxy and different pools.

I don't want to fiddle with the overclocking just yet, I'll let a braver man lead the way there.

[Caesium]

Our units are already overclocked aren't they? They came at 1.2v, all you have to do is press "Switch Clock" to go to High.

[michelet]

Yes I think they are already overclocked.
I also have a blade from first auction and for that I had to change manually the voltage to 1.2.
These are already preset to 1.2V

[Omen1855]

Did anyone start plotting the regions yet in which Asic Miners are running? Would be nice to see where all this hashing power is travelling to.

[desired_username]

Anyone care to post how many BTCs did their HW got in the first 24h?

Mine will complete the 1st 24h in 1,5 hours. (got 3.57 so far)

[drlatino999]

Mine seem to max out around 11.5GH each.. i checked the voltage and they're all at ~1.20-1.23V, clock setting: High

For the people that are seeing 13GH, have you done anything different or tweaked anything in your setup?

is that 13GH on the web blade web interface? or as reported by your pool?

I also noticed a serious difference between slush pool results and bitminter with getwork. Former goes up to 13 GH/s the latter 3 GH/s, while bitminter does report 10 GH/s. So try with a stratum proxy and different pools.

I don't want to fiddle with the overclocking just yet, I'll let a braver man lead the way there.

I'm checking back in, bitminter 6 hours in is reporting just under 6 gh/s. I'm going to check the voltage settings when I get home, this seems too low.

Setup

Erupter (192.168.1.20)
->
Local Stratum Proxy (192.168.1.10)
->
Bitminter

[Caesium]

Anyone care to post how many BTCs did their HW got in the first 24h?

Mine will complete the 1st 24h in 1,5 hours. (got 3.57 so far)

3.57?! How? With 4 blades right?

Mine have only been running about 10 hours but that's enough to make a decent forecast.. exactly 1BTC mined so far (though I was messing about with configs for some of it and rebooting them a bit), so I should be at about 2.4BTC after 24h.

This matches what IRC says..

21:03 <+Caesium> ;; genrate 50000
21:03 <+gribble> The expected generation output, at 50000.0 Mhps, given difficulty of 10076292.8834, is 2.49549374085 BTC per day and 0.103978905869 BTC per hour.

So after fees 2.4BTC looks decent enough..

[lan787]

Anyone care to post how many BTCs did their HW got in the first 24h?

Mine will complete the 1st 24h in 1,5 hours. (got 3.57 so far)

I got 0.8BTC in first day. Few hours blade was offline as I was experimenting with the cooling. Lucky

[desired_username]

Anyone care to post how many BTCs did their HW got in the first 24h?

Mine will complete the 1st 24h in 1,5 hours. (got 3.57 so far)

3.57?! How? With 4 blades right?

Mine have only been running about 10 hours but that's enough to make a decent forecast.. exactly 1BTC mined so far (though I was messing about with configs for some of it and rebooting them a bit), so I should be at about 2.4BTC after 24h.

This matches what IRC says..

21:03 <+Caesium> ;; genrate 50000
21:03 <+gribble> The expected generation output, at 50000.0 Mhps, given difficulty of 10076292.8834, is 2.49549374085 BTC per day and 0.103978905869 BTC per hour.

So after fees 2.4BTC looks decent enough..

yes, 4 blades.

[dogie]

On stock clocks mine run at 10.7. Overclocked after an hour 12.450 on both which is a bit disappointing

Temps are pretty hot too even with 120mm on heatsink and the 2 small fans on the power board.

[candoo]

Hey folks,

iam working on a tutorial to mount the block erupter in the avalon case! At the spot where the 4th module should be.

Anyone intrested in a tutorial?  If so, you may pay me some cents to get it a little bit quicker online.!

[desired_username]

On stock clocks mine run at 10.7. Overclocked after an hour 12.450 on both which is a bit disappointing

Temps are pretty hot too even with 120mm on heatsink and the 2 small fans on the power board.

I think it's normal. I mean at this very moment I read 12.5, 12.9, 12.8, 12.9 all on high clock.

Also, it can fluctuate quite a bit.

____


the first 24h completed, it did 3.96 so 0.99 / blade.

[Caesium]

the first 24h completed, it did 3.96 so 0.99 / blade.

Which pool is this on? Seems like some really good luck?

[drlatino999]

Anyone have issues with their board resetting all the time according to the web interface? I'm lucky for it to stay on for more than 15 minutes before it drops and resets.

[friedcat]

Anyone have issues with their board resetting all the time according to the web interface? I'm lucky for it to stay on for more than 15 minutes before it drops and resets.

The boards reset when there are period of time during which not enough shares are accepted. So there must be problem either with the network setting or the board itself.

Please first try using a backup proxy/port/userpass combination that is different to the primary one. Also please check the hashrate reported by the web interface. If there are further problem, please contact me.

[drlatino999]

Anyone have issues with their board resetting all the time according to the web interface? I'm lucky for it to stay on for more than 15 minutes before it drops and resets.

The boards reset when there are period of time during which not enough shares are accepted. So there must be problem either with the network setting or the board itself.

Please first try using a backup proxy/port/userpass combination that is different to the primary one. Also please check the hashrate reported by the web interface. If there are further problem, please contact me.

Will do, I'll let it run overnight and report what it gives back.  What exactly does this part of the web interface mean?

Chip: OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO

Image here