joaocha
|
|
September 05, 2017, 03:50:49 PM |
|
I noticed something else: Eminer power consumption hashrate +0.3% 30.04MH vs 29.92MH(Claymore 10.0) hynix 8G memory RX580 http://imgur.com/a/O15hj Claymore power consumption: http://imgur.com/a/2gFB4A few watts up. Its either due to higher intensity or kernel needs polishing Where do i get Gpustat for amd? i want to check on simplemining os
|
|
|
|
Edacra
|
|
September 05, 2017, 03:56:03 PM |
|
Well it works fine for me, results even more than some other miner.
|
|
|
|
laik2
|
|
September 05, 2017, 04:35:28 PM |
|
I noticed something else: Eminer power consumption hashrate +0.3% 30.04MH vs 29.92MH(Claymore 10.0) hynix 8G memory RX580 http://imgur.com/a/O15hj Claymore power consumption: http://imgur.com/a/2gFB4A few watts up. Its either due to higher intensity or kernel needs polishing Thanks for your feedback. like intensity, I can advise 28 for RX580, can you set the intensity on parameters? Hashrate drops with about 3% after setting intensity to 28. From 30.04 to 29.5 roughly, power consumption doesn't change much...about 1W roughly.
|
|
|
|
laik2
|
|
September 05, 2017, 04:45:16 PM |
|
I noticed something else: Eminer power consumption hashrate +0.3% 30.04MH vs 29.92MH(Claymore 10.0) hynix 8G memory RX580 http://imgur.com/a/O15hj Claymore power consumption: http://imgur.com/a/2gFB4A few watts up. Its either due to higher intensity or kernel needs polishing Where do i get Gpustat for amd? i want to check on simplemining os You can't, I wrote that.
|
|
|
|
dacutey1023
Newbie
Offline
Activity: 32
Merit: 0
|
|
September 05, 2017, 05:18:26 PM |
|
Do you have a list of commands that we can use ? update: Disregard I found it.
|
|
|
|
smparo
Newbie
Offline
Activity: 27
Merit: 0
|
|
September 05, 2017, 07:00:26 PM |
|
Maybe a bug: sometimes the software reverses video cards, I noticed this because I did some updates today and when I restart the system the fan speed settings are applied to the wrong cards... I solved applying to all the cards the same fan speed for now.
This is the output of the command "eminer -L" when the cards are reversed (note "Device ID for mining" and "PCI bus id")
+--------------------------------------------------+ | OPENCL DEVICES | +--------------------------------------------------+
=================== PLATFORMS ====================
Platform ID 0 Platform Name AMD Accelerated Parallel Processing Platform Vendor Advanced Micro Devices, Inc. Platform Version OpenCL 2.0 AMD-APP (2442.10) Platform Extensions cl_khr_icd cl_khr_d3d10_sharing cl_khr_d3d11_sharing cl_khr_dx9_media_sharing cl_amd_event_callback cl_amd_offline_devices Platform Profile FULL_PROFILE
=== DEVICE #0 === Device ID for mining 0 Device Name Ellesmere Vendor Advanced Micro Devices, Inc. Version OpenCL 2.0 AMD-APP (2442.10) Driver version 2442.10 Address bits 64 Max clock freq 1150 Global mem size 8589934592 Max constant buffer size 4244635648 Max mem alloc size 4244635648 Max compute units 36 Max work group size 256 Max work item sizes [256 256 256] PCI bus id 2
=== DEVICE #1 === Device ID for mining 1 Device Name Ellesmere Vendor Advanced Micro Devices, Inc. Version OpenCL 2.0 AMD-APP (2442.10) Driver version 2442.10 Address bits 64 Max clock freq 1150 Global mem size 8589934592 Max constant buffer size 4244635648 Max mem alloc size 4244635648 Max compute units 36 Max work group size 256 Max work item sizes [256 256 256] PCI bus id 1
====================================================
|
|
|
|
laik2
|
|
September 06, 2017, 04:32:59 AM |
|
A small remark. I am currently mining etc, not eth. Noticed that devfee switches to Eth and generates new DAG each time it switches to devfee, please consider using etc devfee also.
|
|
|
|
E-Miner (OP)
Newbie
Offline
Activity: 58
Merit: 0
|
|
September 06, 2017, 08:41:44 AM |
|
Maybe a bug: sometimes the software reverses video cards, I noticed this because I did some updates today and when I restart the system the fan speed settings are applied to the wrong cards... I solved applying to all the cards the same fan speed for now.
This is the output of the command "eminer -L" when the cards are reversed (note "Device ID for mining" and "PCI bus id")
+--------------------------------------------------+ | OPENCL DEVICES | +--------------------------------------------------+
=================== PLATFORMS ====================
Platform ID 0 Platform Name AMD Accelerated Parallel Processing Platform Vendor Advanced Micro Devices, Inc. Platform Version OpenCL 2.0 AMD-APP (2442.10) Platform Extensions cl_khr_icd cl_khr_d3d10_sharing cl_khr_d3d11_sharing cl_khr_dx9_media_sharing cl_amd_event_callback cl_amd_offline_devices Platform Profile FULL_PROFILE
=== DEVICE #0 === Device ID for mining 0 Device Name Ellesmere Vendor Advanced Micro Devices, Inc. Version OpenCL 2.0 AMD-APP (2442.10) Driver version 2442.10 Address bits 64 Max clock freq 1150 Global mem size 8589934592 Max constant buffer size 4244635648 Max mem alloc size 4244635648 Max compute units 36 Max work group size 256 Max work item sizes [256 256 256] PCI bus id 2
=== DEVICE #1 === Device ID for mining 1 Device Name Ellesmere Vendor Advanced Micro Devices, Inc. Version OpenCL 2.0 AMD-APP (2442.10) Driver version 2442.10 Address bits 64 Max clock freq 1150 Global mem size 8589934592 Max constant buffer size 4244635648 Max mem alloc size 4244635648 Max compute units 36 Max work group size 256 Max work item sizes [256 256 256] PCI bus id 1
====================================================
Thanks, thats just for OpenCL, the miner doesnt change any order, I will try map the correct order via PCI Bus ids.
|
|
|
|
E-Miner (OP)
Newbie
Offline
Activity: 58
Merit: 0
|
|
September 06, 2017, 08:51:16 AM |
|
A small remark. I am currently mining etc, not eth. Noticed that devfee switches to Eth and generates new DAG each time it switches to devfee, please consider using etc devfee also.
Thanks, I will change this next release.
|
|
|
|
Mattthev
|
|
September 06, 2017, 09:07:49 AM |
|
A small remark. I am currently mining etc, not eth. Noticed that devfee switches to Eth and generates new DAG each time it switches to devfee, please consider using etc devfee also.
Thanks, I will change this next release. Same with musicoin would be good.
|
|
|
|
smparo
Newbie
Offline
Activity: 27
Merit: 0
|
|
September 06, 2017, 11:36:15 AM |
|
do you have manual or readme ho to use it??
There is no manual, only the comand "eminer -h" for help If you use ethermine you can use this command (for me intensity 30 is the best value and I have the fan set at 75%) eminer.exe -S eu1.ethermine.org:4444 -U your_address -P x -intensity 30,30 -fan-percent 75,75
|
|
|
|
bitcoyim
Member
Offline
Activity: 65
Merit: 10
|
|
September 06, 2017, 03:01:50 PM |
|
when i put eminer -h at my .bat, its auto close
just open command promt (cmd) Go to your eminer folder, for example: cd C:\user\test\desktop\eminer eminer.exe -h -> type this
|
|
|
|
Mattthev
|
|
September 06, 2017, 05:25:19 PM |
|
when i put eminer -h at my .bat, its auto close
At the end of the batch file put pause, it won't close.
|
|
|
|
christianCoder
Newbie
Offline
Activity: 13
Merit: 0
|
|
September 06, 2017, 06:24:44 PM |
|
Do I have to enter my wallet password in the eminer config file for this to work?
|
|
|
|
E-Miner (OP)
Newbie
Offline
Activity: 58
Merit: 0
|
|
September 06, 2017, 06:41:24 PM |
|
Do I have to enter my wallet password in the eminer config file for this to work?
Of course no, you should enter stratum password.
|
|
|
|
christianCoder
Newbie
Offline
Activity: 13
Merit: 0
|
|
September 06, 2017, 06:48:12 PM |
|
Of course no, you should enter stratum password.
Ok, so I'm currently using Claymore's with ethermine.org My Claymore config file doesn't have a stratum password. So will eminer work without one? If not, how do I create a stratum account and get a password?
|
|
|
|
E-Miner (OP)
Newbie
Offline
Activity: 58
Merit: 0
|
|
September 06, 2017, 07:26:39 PM |
|
Of course no, you should enter stratum password.
Ok, so I'm currently using Claymore's with ethermine.org My Claymore config file doesn't have a stratum password. So will eminer work without one? If not, how do I create a stratum account and get a password? You can use x as a password for ethermine.org.
|
|
|
|
christianCoder
Newbie
Offline
Activity: 13
Merit: 0
|
|
September 06, 2017, 07:37:19 PM Last edit: September 06, 2017, 10:55:25 PM by christianCoder |
|
Of course no, you should enter stratum password.
Ok, so I'm currently using Claymore's with ethermine.org My Claymore config file doesn't have a stratum password. So will eminer work without one? If not, how do I create a stratum account and get a password? You can use x as a password for ethermine.org. Thanks for clarifying! This seems very legit! With the devfee on, we're currently getting 3Mh/s more with Eminer than with Claymore.For anyone else using Claymore on linux, the bare minimum equivalent for Eminer is: ./eminer -S us1.ethermine.org:4444 -U wallet_address -P x This can be placed in a shell script to execute on system boot. Here is the output from the Eminer help file: christianCoder$ ./eminer -h
Usage of ./eminer: -B int Run benchmark (default -1) -F string Farm mode with the work server at URL, use comma for multiple rpc server (default "http://127.0.0.1:8545") -L List GPU devices -M string Run mine on selected devices, use comma for multiple devices (default "all") -N string Name of your worker -P string Password for stratum server -S <host>:<port> Stratum mode, use comma for multiple stratum server (example: <host>:<port>) -U string Username for stratum server -V int Log level (default 3) -cpu int Set the maximum number of CPUs to use -fan-percent string Set fan speed percent on selected devices, use comma for multiple devices (amd devices only) -fixed-diff Fixed diff for works, round solutions -http string HTTP server for monitoring (read-only) for disable set "no" (default ":8550") -intensity string GPU work size intensity, use comma for multiple devices (default: 32) -kernel string Select kernel for GPU devices, currently 3 kernels available, use comma for multiple devices -no-devfee Disable devfee, this can be impact some performance reduces -no-output-color Disable colorized output log format -stathat string Set your stathat email address here to have some basic metrics from stathat.com -v Version
|
|
|
|
E-Miner (OP)
Newbie
Offline
Activity: 58
Merit: 0
|
|
September 07, 2017, 07:55:47 AM |
|
for me, when i use eminer with amd ma gash rate drop to 28++ i i use claymore my hashrate 32++
Please give me name of your OS and the AMD device.
|
|
|
|
bitcoyim
Member
Offline
Activity: 65
Merit: 10
|
|
September 07, 2017, 08:27:40 AM Last edit: September 07, 2017, 08:50:10 AM by bitcoyim |
|
rx 580 saphire+ win 10 64 bit
I have same config with 32mh++ on eminer. Can you give me a teamviewer? I can check your config
|
|
|
|
|