Pangolinminer & Whatsminer FAQs

[ternzer]

I found the problem. I did some searching around the internet and saw a few people had a similar problem but no solutions. So i started reading the miner system logs from the bottom up. I found a line before the CGminer exit lines with port not open...
So...I use awesome miner to monitor the miners. I changed the port to 4028 for the API access. When i did the hard reset this port did NOT revert back to 22.

After switching it back i restarted CGminer in the interface and it fired back up!.

[Shazam!!!]

I'm up and running. I had one, little hiccup, with the cgminer gui. It did not want to accept a pool change, and would not start.
 Did a reset, and it took care of it. Also, where I'm at, it's about 20 degrees Fahrenheit. I had to put them in the garage temporarily,
and it took some time for them to heat up completely. So far, everything is working as it should. I'm seeing speeds at/near 13th/s.

[Raymond_B]

I'm up and running. I had one, little hiccup, with the cgminer gui. It did not want to accept a pool change, and would not start.
 Did a reset, and it took care of it. Also, where I'm at, it's about 20 degrees Fahrenheit. I had to put them in the garage temporarily,
and it took some time for them to heat up completely. So far, everything is working as it should. I'm seeing speeds at/near 13th/s.

In that cold air what temps are you seeing?

[Shazam!!!]

In that cold air what temps are you seeing?

Right now, at 32(23 real) outside and 55 in the garage, I'm getting inbetween 77 to 84, depending on the wind gusts really. The ole
garage isn't quite air tight, and I literally have nothing behind my house but open fields, for 2 miles. I've been monitoring them for
about 15hrs, and they've been very consistent since they warmed up. Still getting 11.9 -12.8 th/s.

[Raymond_B]

In that cold air what temps are you seeing?

Right now, at 32(23 real) outside and 55 in the garage, I'm getting inbetween 77 to 84, depending on the wind gusts really. The ole
garage isn't quite air tight, and I literally have nothing behind my house but open fields, for 2 miles. I've been monitoring them for
about 15hrs, and they've been very consistent since they warmed up. Still getting 11.9 -12.8 th/s.

Good info thanks! These things like to run at high 70s to mid 80s regardless of the ambient temp it seems. I was getting almost the exact temps as you with 60 ish deg intake air. Today it was in the mid 60s and my garage heated up to mid 70s so they are running anywhere from 81-85.

[Shazam!!!]

Good info thanks! These things like to run at high 70s to mid 80s regardless of the ambient temp it seems. I was getting almost the exact temps as you with 60 ish deg intake air. Today it was in the mid 60s and my garage heated up to mid 70s so they are running anywhere from 81-85.

No problem. I can say, earlier this afternoon, my temps were staying above 80, and I was seeing consistent speeds from
12.5 - 13th/s. Theses seem to do their best work, when they can heat up some Hot Chocolate! Hahaha!

[Olds1967]

One thing I noticed unlike my S9's or Avalon power supplies the M3's power supply is cool to the touch.  While the M3 case is very warm and the S9/Avalon are cool to the touch. 

[pandiman]

Hello! Please tell me, one of the miners works for 6 minutes and will reboot. I have voltage regulators, no voltage surges. What could be wrong?

[crypto_curious]

Hello! Please tell me, one of the miners works for 6 minutes and will reboot. I have voltage regulators, no voltage surges. What could be wrong?

Disconnect one hashing board from power supply and check if miner is working fine with only two.

[Shazam!!!]

Hello! Please tell me, one of the miners works for 6 minutes and will reboot. I have voltage regulators, no voltage surges. What could be wrong?

What are you running for your voltage? 120 or 240? Also, in cgminer, check the system log for the reboot error.

[pandiman]

Hello! Please tell me, one of the miners works for 6 minutes and will reboot. I have voltage regulators, no voltage surges. What could be wrong?

What are you running for your voltage? 120 or 240? Also, in cgminer, check the system log for the reboot error.

220 V I use a thyristor voltage regulator

E010   
Miner thread isn't present   
Restart cgminer   
1   
Sat Feb 17 14:30:06 +04 2018   
cgminer-monitor
E011   
Slot-1 Zero HS 180 seconds   
Zero HS Warning   
1   
Wed Feb 14 13:28:48 2018   
system-monitor

[Zaboon]

Hello,

I would like to know if there is an importance filling the pool 2 and pool 3? Cause I filed them but there are not active, only the first one !

Thank you !

[HagssFIN]

Hello,

I would like to know if there is an importance filling the pool 2 and pool 3? Cause I filed them but there are not active, only the first one !

Thank you !

Those are your fallback pools.
So in case your primary pool, pool 1 has an issue, your miner will connect to the pool 2.
If also the pool 2 has an issue, the miner will then connect to the pool 3.

[abc_whats]

how can i change frequency for overclocking?

when edit the file /etc/config/powers ,change the frequency from default to 480 "list 'power_limit' '3:000107:10:480:480:480:0:11500:600:1:1:10300:612:6:1'",then it works!

The GHSav is changed running to 8.7G.

but change the frequency  from default to 648\660，it doesn't works.

The GHSav frequency is always running between 11.5 to 11.9.

[GbrilliantQ]

I still can't believe I missed Feb ship out because of an error on their part.  I ordered Dec 14th and I'll have to wait till March 25th for my order, even though folks who buy today will get theirs the same week as me.   Crazy.  They won't do a single thing about it either.

[mo750]

They so badly promisong i ordered in 28 septamber for feb  and they didnt send me tracking id yet.they should send me before march but no M3 delivered yet.is there any body delivered his m3 for feb batch?

[Vene]

They so badly promisong i ordered in 28 septamber for feb  and they didnt send me tracking id yet.they should send me before march but no M3 delivered yet.is there any body delivered his m3 for feb batch?

Yes, got 2 units Feb batch. Both running great.

[Raymond_B]

They so badly promisong i ordered in 28 septamber for feb  and they didnt send me tracking id yet.they should send me before march but no M3 delivered yet.is there any body delivered his m3 for feb batch?

Had 2 delivered as well no problems and they actually shipped on the 1st day of their expected ship date range.

[Olds1967]

They so badly promisong i ordered in 28 septamber for feb  and they didnt send me tracking id yet.they should send me before march but no M3 delivered yet.is there any body delivered his m3 for feb batch?

Had 2 delivered as well no problems and they actually shipped on the 1st day of their expected ship date range.

Same here.  DHL was painless.  From time they left Hong Kong to my door step was just a couple of days.

[mo750]

If you recieve your m3 So why they dont deliverd my m3 yet?
http://uupload.ir/files/918f_img_20180301_225330.png