ternzer
Newbie
Offline
Activity: 3
Merit: 0
|
|
February 16, 2018, 02:03:08 PM |
|
I found the problem. I did some searching around the internet and saw a few people had a similar problem but no solutions. So i started reading the miner system logs from the bottom up. I found a line before the CGminer exit lines with port not open... So...I use awesome miner to monitor the miners. I changed the port to 4028 for the API access. When i did the hard reset this port did NOT revert back to 22.
After switching it back i restarted CGminer in the interface and it fired back up!.
|
|
|
|
Shazam!!!
Full Member
Offline
Activity: 350
Merit: 158
#takeminingback
|
|
February 18, 2018, 05:41:25 PM |
|
I'm up and running. I had one, little hiccup, with the cgminer gui. It did not want to accept a pool change, and would not start. Did a reset, and it took care of it. Also, where I'm at, it's about 20 degrees Fahrenheit. I had to put them in the garage temporarily, and it took some time for them to heat up completely. So far, everything is working as it should. I'm seeing speeds at/near 13th/s.
|
Click these links to learn some truth about Big Corporate mining pools stealing your money and centralizing BTCitcoin!!! Help support the BTCitcoin community!!! Mine your BTCitcoin at a non-Corporate pool!!! BTC: 1ShazamjsPnpWDNnk3n2tAiKGMdXaSjay
|
|
|
Raymond_B
Member
Offline
Activity: 504
Merit: 71
Just Getting Started...
|
|
February 19, 2018, 01:21:23 AM |
|
I'm up and running. I had one, little hiccup, with the cgminer gui. It did not want to accept a pool change, and would not start. Did a reset, and it took care of it. Also, where I'm at, it's about 20 degrees Fahrenheit. I had to put them in the garage temporarily, and it took some time for them to heat up completely. So far, everything is working as it should. I'm seeing speeds at/near 13th/s.
In that cold air what temps are you seeing?
|
|
|
|
Shazam!!!
Full Member
Offline
Activity: 350
Merit: 158
#takeminingback
|
|
February 19, 2018, 01:36:34 AM |
|
In that cold air what temps are you seeing?
Right now, at 32(23 real) outside and 55 in the garage, I'm getting inbetween 77 to 84, depending on the wind gusts really. The ole garage isn't quite air tight, and I literally have nothing behind my house but open fields, for 2 miles. I've been monitoring them for about 15hrs, and they've been very consistent since they warmed up. Still getting 11.9 -12.8 th/s.
|
Click these links to learn some truth about Big Corporate mining pools stealing your money and centralizing BTCitcoin!!! Help support the BTCitcoin community!!! Mine your BTCitcoin at a non-Corporate pool!!! BTC: 1ShazamjsPnpWDNnk3n2tAiKGMdXaSjay
|
|
|
Raymond_B
Member
Offline
Activity: 504
Merit: 71
Just Getting Started...
|
|
February 19, 2018, 01:48:46 AM |
|
In that cold air what temps are you seeing?
Right now, at 32(23 real) outside and 55 in the garage, I'm getting inbetween 77 to 84, depending on the wind gusts really. The ole garage isn't quite air tight, and I literally have nothing behind my house but open fields, for 2 miles. I've been monitoring them for about 15hrs, and they've been very consistent since they warmed up. Still getting 11.9 -12.8 th/s. Good info thanks! These things like to run at high 70s to mid 80s regardless of the ambient temp it seems. I was getting almost the exact temps as you with 60 ish deg intake air. Today it was in the mid 60s and my garage heated up to mid 70s so they are running anywhere from 81-85.
|
|
|
|
Shazam!!!
Full Member
Offline
Activity: 350
Merit: 158
#takeminingback
|
|
February 19, 2018, 01:57:26 AM |
|
Good info thanks! These things like to run at high 70s to mid 80s regardless of the ambient temp it seems. I was getting almost the exact temps as you with 60 ish deg intake air. Today it was in the mid 60s and my garage heated up to mid 70s so they are running anywhere from 81-85.
No problem. I can say, earlier this afternoon, my temps were staying above 80, and I was seeing consistent speeds from 12.5 - 13th/s. Theses seem to do their best work, when they can heat up some Hot Chocolate! Hahaha!
|
Click these links to learn some truth about Big Corporate mining pools stealing your money and centralizing BTCitcoin!!! Help support the BTCitcoin community!!! Mine your BTCitcoin at a non-Corporate pool!!! BTC: 1ShazamjsPnpWDNnk3n2tAiKGMdXaSjay
|
|
|
Olds1967
Newbie
Offline
Activity: 18
Merit: 0
|
|
February 19, 2018, 02:51:27 AM |
|
One thing I noticed unlike my S9's or Avalon power supplies the M3's power supply is cool to the touch. While the M3 case is very warm and the S9/Avalon are cool to the touch.
|
|
|
|
pandiman
Newbie
Offline
Activity: 2
Merit: 0
|
|
February 19, 2018, 08:51:47 PM |
|
Hello! Please tell me, one of the miners works for 6 minutes and will reboot. I have voltage regulators, no voltage surges. What could be wrong?
|
|
|
|
crypto_curious
|
|
February 19, 2018, 08:59:44 PM |
|
Hello! Please tell me, one of the miners works for 6 minutes and will reboot. I have voltage regulators, no voltage surges. What could be wrong?
Disconnect one hashing board from power supply and check if miner is working fine with only two.
|
|
|
|
Shazam!!!
Full Member
Offline
Activity: 350
Merit: 158
#takeminingback
|
|
February 19, 2018, 09:41:01 PM |
|
Hello! Please tell me, one of the miners works for 6 minutes and will reboot. I have voltage regulators, no voltage surges. What could be wrong?
What are you running for your voltage? 120 or 240? Also, in cgminer, check the system log for the reboot error.
|
Click these links to learn some truth about Big Corporate mining pools stealing your money and centralizing BTCitcoin!!! Help support the BTCitcoin community!!! Mine your BTCitcoin at a non-Corporate pool!!! BTC: 1ShazamjsPnpWDNnk3n2tAiKGMdXaSjay
|
|
|
pandiman
Newbie
Offline
Activity: 2
Merit: 0
|
|
February 20, 2018, 04:48:44 AM |
|
Hello! Please tell me, one of the miners works for 6 minutes and will reboot. I have voltage regulators, no voltage surges. What could be wrong?
What are you running for your voltage? 120 or 240? Also, in cgminer, check the system log for the reboot error. 220 V I use a thyristor voltage regulator E010 Miner thread isn't present Restart cgminer 1 Sat Feb 17 14:30:06 +04 2018 cgminer-monitor E011 Slot-1 Zero HS 180 seconds Zero HS Warning 1 Wed Feb 14 13:28:48 2018 system-monitor
|
|
|
|
Zaboon
Newbie
Offline
Activity: 2
Merit: 0
|
|
February 20, 2018, 09:57:16 AM |
|
Hello,
I would like to know if there is an importance filling the pool 2 and pool 3? Cause I filed them but there are not active, only the first one !
Thank you !
|
|
|
|
HagssFIN
Legendary
Offline
Activity: 2464
Merit: 1710
Electrical engineer. Mining since 2014.
|
|
February 20, 2018, 10:09:36 AM |
|
Hello,
I would like to know if there is an importance filling the pool 2 and pool 3? Cause I filed them but there are not active, only the first one !
Thank you !
Those are your fallback pools. So in case your primary pool, pool 1 has an issue, your miner will connect to the pool 2. If also the pool 2 has an issue, the miner will then connect to the pool 3.
|
|
|
|
abc_whats
Newbie
Offline
Activity: 1
Merit: 0
|
|
February 23, 2018, 10:27:25 AM |
|
how can i change frequency for overclocking?
when edit the file /etc/config/powers ,change the frequency from default to 480 "list 'power_limit' '3:000107:10:480:480:480:0:11500:600:1:1:10300:612:6:1'",then it works!
The GHSav is changed running to 8.7G.
but change the frequency from default to 648\660,it doesn't works.
The GHSav frequency is always running between 11.5 to 11.9.
|
|
|
|
GbrilliantQ
Full Member
Offline
Activity: 189
Merit: 100
ƃqɹᴉllᴉɐuʇb
|
|
February 25, 2018, 07:28:07 PM |
|
I still can't believe I missed Feb ship out because of an error on their part. I ordered Dec 14th and I'll have to wait till March 25th for my order, even though folks who buy today will get theirs the same week as me. Crazy. They won't do a single thing about it either.
|
|
|
|
mo750
Newbie
Offline
Activity: 4
Merit: 0
|
|
March 01, 2018, 01:49:00 PM Last edit: March 01, 2018, 03:08:48 PM by mo750 |
|
They so badly promisong i ordered in 28 septamber for feb and they didnt send me tracking id yet.they should send me before march but no M3 delivered yet.is there any body delivered his m3 for feb batch?
|
|
|
|
Vene
Member
Offline
Activity: 133
Merit: 11
|
|
March 01, 2018, 03:34:07 PM |
|
They so badly promisong i ordered in 28 septamber for feb and they didnt send me tracking id yet.they should send me before march but no M3 delivered yet.is there any body delivered his m3 for feb batch?
Yes, got 2 units Feb batch. Both running great.
|
|
|
|
Raymond_B
Member
Offline
Activity: 504
Merit: 71
Just Getting Started...
|
|
March 01, 2018, 04:57:57 PM |
|
They so badly promisong i ordered in 28 septamber for feb and they didnt send me tracking id yet.they should send me before march but no M3 delivered yet.is there any body delivered his m3 for feb batch?
Had 2 delivered as well no problems and they actually shipped on the 1st day of their expected ship date range.
|
|
|
|
Olds1967
Newbie
Offline
Activity: 18
Merit: 0
|
|
March 01, 2018, 06:33:04 PM |
|
They so badly promisong i ordered in 28 septamber for feb and they didnt send me tracking id yet.they should send me before march but no M3 delivered yet.is there any body delivered his m3 for feb batch?
Had 2 delivered as well no problems and they actually shipped on the 1st day of their expected ship date range. Same here. DHL was painless. From time they left Hong Kong to my door step was just a couple of days.
|
|
|
|
|
|